Ethernet Network Protocol Menu Parameters | Avocent Cyclades-PR2000

Cyclades-PR2000

STEP ONE

The first step is to determine the parameters needed to configure the Ethernet interface (ETH0). The parameters in the Network Protocol Menu (IP) are shown in Figure 4.10. Fill in the blanks for your application in the right-most column. These parameters will be entered into the router later, after all parameters have been chosen. Each parameter in this menu is explained in more detail in chapter 5 of the Installation Manual.

Menu CONFIG=>INTERFACE=>ETHERNET=>NETWORK PROTOCOL=>IP

Parameter	Example		Your Application
Active or Inactive	Active enables IP communication (IPX and
	Transparent Bridge are not used in this
	example).
Interface Unnumbered	Numbered
Primary IP Address	100.130.130.1
Subnet Mask	255.255.255.0
Secondary IP Address	0.0.0.0 for none.
IP MTU	Use the preset value, 1500.	This determines
	whether or not a given IP datagram is
	fragmented.
NAT	Global, because NAT is not being used in this
	example.
ICMP Port	Inactive
Incoming Rule List	None, filters are not included in this example.
Outgoing Rule List Name	None, filters are not included in this example.
Proxy ARP	Inactive
IP Bridge	Inactive

FIGURE 4.10 ETHERNET NETWORK PROTOCOL MENU PARAMETERS

Chapter 4 - Step-by-Step Instructions

28

Image 28

Avocent Cyclades-PR2000 installation manual Ethernet Network Protocol Menu Parameters

Contents

Cyclades-PR2000 FCC Warning Statement Cyclades-PR2000 Installation ManualCanadian DOC Notice Table of Contents Static Routing Dynamic Routing 112 127 HOW to USE this Manual Installation Assumptions Text Conventions CONFIG=INTERFACE=L Convention DescriptionIcons Icon Meaning Why CONFIGURATION=ALL Cyclades Technical Support and Contact Information Cyclades Corporation USA To Wall Outlet Gender Changer DB-25 DB-9 Male What is in the BOXInterface RJ-45 Male RJ-45 to DB-25 DB-25 Male RS-232 Modem With DB-25 Interface Using CyROS Menus Login Prompt and Main Menu Lmi-typeANSI, Group of four, None Ansi CONFIGURATION=TO Flash Special Keys Cyros Management Utility CyROS Management Utility Cyclades-PR2000 STEP-BY-STEP Instructions for Common Applications RS-232 Modem Network IP PC192.168.0.0Host PR2000 Host 192.168.0.30 255.255.255.0 Step ONE Parameter Example Your ApplicationIP MTU NAT Step TWO Step Three Swan Network Protocol IP Menu Parameters Step Four Mlppp Step Five Step SIX Step Eight Step SevenStep Nine Instructions for creating a backup of the configuration file Instructions for listing the configuration Example 2 a LAN-to-LAN Example Using Frame Relay Network IP MaskETH0 PR2000 200.240.230.1 10 Ethernet Network Protocol Menu Parameters 11 Swan Physical Menu Parameters 12 Swan Network Protocol IP Menu Parameters LMI Snap IPCIR 14 DLC Configuration Menu Parameters Dlci 15 Static Route Menu Parameters Instructions for creating a backup of the configuration file Example 3 Link Backup 17 Traffic Control Parameters Swan 18 Addition of the Primary Main Link This parameter has no effect for link backup. For load 20 Multilink Circuit Attributes 21 Static Backup Route Parameters Instructions for creating a backup of the configuration file IP Network Protocol Configuration of the Ethernet InterfaceParameter Description Config =RULES LIST=IP=CONFIGURE RULES=ADD RULE=ALLOW Incoming IP Accounting IP Bridge 200.240.240.9 200.240.240.3 200.240.240.2 200.240.240.1PR2000 Link PR3000 200.240.240.8 200.240.240.4 Other Parameters Swan and Async Interfaces Clock Source is always External Step TWO Protocol Be used for authentication Network Protocols Network Protocol IP Protocol Detailed Incoming IP Accounting Transparent Bridge Protocol DATA-LINK Protocols Encapsulation PPP The Point-to-Point Protocol PPP Menu Char Hdlc PppcharFrame Relay CONFIG=INTERFACE=SWAN =TRAFFIC Control =GENERAL =BANDWIDTH T391 Interval between the LMI Status Enquiry messages N391 Dlci 200.1.1.1 São Paulo Rio de Janeiro Network Salvador Recife Network For static address mapping Switch / DCE Router / DTE Menu CONFIG=INTERFACE=LINK=ENCAPSULATION =X.25 Menu With PAD Packet Assembler/Disassembler Routing Protocols Routing StrategiesStatic Routing Dynamic Routing Static Routes 142.10.0.0 Mask192.168.100.0 10.0.0.0 Unnumbered Interfaces Add Static Route Menu Config =STATIC Routes =IP =ADD Route RIP Configuration Ospf Ospf Configuration on the Interface 10Mbps, 65 for T1, 1785 for 56kbps, etc Ospf Global Configurations =PASSWORD CONFIG=STATIC ROUTES=IP=ADD ROUTE=OSPF Advertises this=ROUTING Protocol =OSPF =ADVERTISE this NON-OSPF Interface Applies when Area Range N Status is Active Only when Virtual Link Status is Active =IP=OSPF=AREA=AUTHENTICATION Type BGP-4 Configuration Example System with PR2000 in AS 100 Being Configured 255.255.255.0 200.50.50.0 PR3000 200.200.200.2 Tele Brutus CONFIG=IP=BGP4=GLOBAL CONFIG=IP=BGP4=BGP NETWORK=ADD CONFIG=IP=BGP4=NEIGHBOR=ADD Route Reflector Client Step Three Up Ro 100.10.0.0/16 Route PR3000 RredParameter Description Routes Seq Rule Message From Tele Popeye Route Map Parameter Description DiscardedDiscarded RoutesRoutes Seq RuleMessage From Tele Popeye Rule CONFIG=IP=BGP4=ROUTE MAP=ADD CONFIG=IP=BGP4=AGGREGATE ADDRESSES=ADD CYROS, the Operating System Creation of user accounts and passwordsCreation of the host table Slip Detailed information can be accessed via Snmp IP Accounting NAT Network Address Translation Global Address Range Ftp Network Server MaskNetworks 192.168.0.0 Server 192.168.0.31 Translated Types of Address Translation Menu Option Description Interface. Five minutes is a reasonable time Step Four Configuration of IP Filters Rules and Filters Rules List Rule List Exterior Router Perimeter Network Slot 192.168.0.0 Bastion Host 10.0.0.0 Extension to Network Let Mail out Exterior RouterLet Telnet Connections Out Filters and Rules 100 Output for Exterior Router Example Filters and Rules 102 Interior Router Stop Forged Packets Don’t Allow Access to NewsStop Telnets From the Outside Except Bastion Host Output for Interior Router Example Link 33.33.33.1 25% or less Traffic Rule ListsClient B Filters and Rules 106 Output Showing Parameters for Traffic Rule Example Filters and Rules 108 Port 25 Smtp Mail Server Web ServerMail Server Web Client 10 Output Showing Parameters for Traffic Rule Example Internal Network IPX Internetwork Packet ExchangeNumber Mac Address 00 60 2E 00 11 Configuring Other Interfaces Configuring the Ethernet InterfaceEnabling IPX Routing Frame RelayParameter Value for the Example SAP Service Advertisement Protocol Table Routing Table for the Example Virtual Private Network Configuration Virtual Private Network Configuration 116 Link IP10..255.255.0 Router IP AddressRSG3 Remote IP Network 9.1 Security Gateway Router Link IP172.16.0.0 Link Virtual Private Network Configuration 118 Virtual Private Network Configuration 119 Appendix a Troubleshooting Boot Code stepTest CPU What to Do if the Router Does Not Work or Stops Working Event CPU LED Morse code Testing the Ethernet Interface Host host00 Testing the WAN Interfaces Figure A.3 General Statistics Table Appendix a Troubleshooting 124 Cyclades PR2000 LEDs Appendix B Hardware Specifications WAN Interfaces External InterfacesLAN Interface Asynchronous Interface Console Interface Cables Straight-Through Cable Female Retention Screw Male DB-25 Female Signal Pin PGnd DB-25 M.34 AdaptorTxClkDTE B TxClkDTE a ASY/Modem Cable Cross Cable Cross Cable Signal Pin Pin Signal PGnd TxD RxD20 DTR DB-25 Loopback Connector Figure B.10 Loopback Connector DB-25 Male Procedure Appendix C Configuration Without a ConsoleRequirements RIP Snmp Cyclades Philippines