Bosch Appliances D6100 Modem IIIa2 Messages continued, Bosch Security Systems, Inc. 1/07, Comex

Conettix D6600/D6100 Computer Interface Manual Appendix C: Modem IIIa2 Messages

Table 92: Modem IIIa2 Messages (continued)

	Event	Device/Mode	Display				Explanation	Refer to Section
								C.1 Zonex and
								Comex
								Translation on
								page 137.
655.	SDI Restoral	Printer:	dd/dd tt:tt Lxx ACC aaa RESTORAL			ZN D	Zonex restoral	2.
		D6500 Mode:	h1rrlssssssaaaasRsssDt				message: indicates a
		SIA Mode:	<header>[#aaaaNURD]				trouble condition on
							the wiring from the
							POPEX Module to the
							POPITs was cleared.
							Wiring connecting the
							control panel and
							keypads restored. Point
							bus, supervised
							keypad, printer, or
							other serial device was
							restored.
656.	SDI Restoral	Printer:	dd/dd tt:tt Lxx ACC aaaa		SDI RESTORAL		The supervised
			+++ ACC aaaa		SDI=ddd		keypad, printer, or
		D6500 Mode:	h1rrlssssssaaaasRsssDt				other serial device
		SIA Mode:	<header>[#aaaaNpidddER]				listed in the second
							line of the report was
							restored.
657.	SDI Restoral	Printer:	dd/dd tt:tt Lxx ACC aaaa		SDI RESTORAL		The supervised
	(Point		+++ ACC aaaa	POINT=ppp SDI=ddd			keypad, printer, or
	reported)	D6500 Mode:	h1rrlssssssaaaasRspppt				other serial device
		SIA Mode:	<header>[#aaaaNpidddERppp]				listed in the second
							line of the report was
							restored.
658.	Sensor Reset	Printer:	dd/dd tt:tt Lxx ACC aaaa		SENSOR RESET		The sensor specified in	1,
			+++ ACC aaaa	AREA=a ID=iii RELAY#=rrr			the second line of the	7,
		D6500 Mode:	h1rrlssssssaaaasNsD27t				report (labeled
		SIA Mode:	<header>[#aaaaNria/idiiiXIrrr]				“RELAY”) located in	8.
							the specified AREA
							was reset by a user
							with the ID shown.
659.	Sensor Reset	Printer:	dd/dd tt:tt Lxx ACC aaaa		SENSOR RESET		The sensor specified in	1,
	(ID not		+++ ACC aaaa	AREA=a RELAY#=rrr			the second line of the	7,
	reported)	D6500 Mode:	h1rrlssssssaaaasNsD27t				report (labeled
		SIA Mode:	<header>[#aaaaNriaXIrrr]				“RELAY”) located in	8 ,
							the specified AREA
							was reset by a user	D7112
							with the ID shown.
660.	Sensor Reset	Printer:	dd/dd tt:tt Lxx ACC aaaa		SENSOR RESET		The sensor specified in	1,
	(ID/relay not		+++ ACC aaaa			AREA=a	the second line of the	7,
	reported)	D6500 Mode:	h1rrlssssssaaaasNsD27t				report (labeled
		SIA Mode:	<header>[#aaaaNriaXI]				“RELAY”) located in	8 ,
							the specified AREA
							was reset by a user	D7112
							with the ID shown.
661.	Sensor Reset	Printer:	dd/dd tt:tt Lxx ACC aaaa		SENSOR RESET
	(relay > 254,		+++ACC aaaa	AREA=aa ID=iii RELAY#=rrrr
	user < 255)	D6500 Mode:	h1rrlssssssaaaasNsD27t
		SIA Mode:	<header>[#aaaaNriaa/idiiiXIrrrr]
662.	Sensor Reset	Printer:	dd/dd tt:tt Lxx ACC aaaa		SENSOR RESET
	(relay > 254,		+++ACC aaaa	AREA=a ID=iiii RELAY#=rrrr
	user >254)	D6500 Mode:	h1rrlssssssaaaasNsD27t
		SIA Mode:	<header>[#aaaaNria/idiiiiXIrrrr]
663.	Sensor Reset	Printer:	dd/dd tt:tt Lxx ACC aaaa		SENSOR RESET
	(relay < 255,		+++ACC aaaa	AREA=aa ID=iii RELAY#=rrr
			h1rrlssssssaaaasNsD27t
	user < 255)	D6500 Mode:
	(OMNI)	SIA Mode:	<header>[#aaaaNria/idiiiXIrrr]

Bosch Security Systems, Inc. 1/07 4998122703-01 117