Bosch Appliances D6100, D6600 manual C.1 Zonex and Comex Translation, Point to Zonex Translation

Conettix D6600/D6100 Computer Interface Manual Appendix C: Modem IIIa2 Messages

C.1 Zonex and Comex Translation

These numbered items correspond to the number in the last column in Table 92 starting on page 61.

1.The D7112/D9112 verifies the user identification and point data formats and sends them to the automation system. If the control panel requests a translation, the D6600/D6100 converts point data to Zonex format and user IDs to Comex format. If there is no request for translation, points and IDs are sent to the automation PC and print on the connected printer with no conversion. Table 94 shows the translation of User IDs and Table 93 shows the translation of point data.

Table 93: Point to Zonex Translation

Point	ZONEX
001-008	100-800
009-024	101-116
025-040	201-216
041-056	301-316
057-072	401-416
073-088	501-516
089-104	601-616
105-120	701-716
121-136	801-816
137-152	117-132
153-168	217-232
169-184	317-332
185-200	417-432
201-216	517-532
217-232	617-632
233-247	717-731

Table 94: User ID to Comex Translation

ID	COMEX
0	0
1-5	001-005
0-13	601-608
14-21	701-708
22-29	801-808
30-37	B01-B08
38-45	C01-C08
46-53	D01-D08
54-61	E01-E08
62-69	F01-F08
70-249	000

2.A D7112 using the Modem II format can transmit these messages.

3.Not used.

4.When the D7112 is transmitting a test report in Modem II format, the area number is sent to the automation system if the output format is in SIA communications mode.

Example 1: Log Threshold Since Last Call

<header>[#aaaaOriaJL]

5.When transmitted by a D7112, the identification number, if any, also prints. Refer to Forced Point in the D9112B Program Entry Guide

(P/N: 74-06145-000-D).

6.Not entering a phone number turns off these messages for the event class. All messages in this class exist in a unique event class.

7.For these events, the area denotes the location of the keypad used to initiate the event (see Sensor Reset).

8.BFSK Format: For the D9112, unless otherwise specified, the zone digit “z” uses the “BFSK Zone Code” as a base for a given point. This code is programmed in the control panel by point. The zone digit “i” indicates the most significant digit of the user ID.

9.For the D7112, unless otherwise specified, Table 95 is the basis for the zone digit “z” and ID translation; however, actual IDs only go up to 25.

Table 95: Reported Zone/ID to Actual Point/ID

Reported Zone/ID

	1	2	3	4	5	6	7	8
Actual	1	2	3	4	5	6	7	8
Point/ID
	9	10	11	12	13	14	15	16

17	18	19	20	21	22	23	24
25	26	27	28	29	30	31	32
33	34	35	36	37	38	39	40
41	42	43	44	45	46	47	48

10.This message reports from a D7112 RF point. The internal or external printer prints the label “RF POINT=” instead of “POINT=” in the second line (Example 2).

Example 2: Label RF Point

dd/dd tt:tt ql ACC aaaa FIRE ALARM

+++ ACC aaaa AREA=a RF POINT=ppp

Bosch Security Systems, Inc. 1/07 4998122703-01 137