Bosch Appliances D9412G, D7412G Programming a Primary and Backup Destination, Enhanced Routing

D9412G/D7412G Program Entry Guide 2.0 9000MAIN

EN 16

2.3.3Programming a Primary and Backup Destination

Each route number has an R# Primary Device and an R# Backup Device. In typical applications where two phone numbers are programmed, the R# Primary Device destination is the phone number the route group attempts to dial first. If the R# Primary Device destination fails to connect to the central station receiver after two dialing attempts, the R# Backup Device destination is dialed. In addition, the control panel can be programmed so the R# Primary Device and/or the R# Backup Device can be an SDI device, such as a D9133TTL- E Network Interface Module. The control panel can also be programmed to make only one attempt for the R# Primary Device before attempting to send events using the R# Backup Device.

2.3.4Enhanced Routing

In previous versions, only Phone numbers 1 through 4 could be programmed for the Primary and Backup Destinations. The D9412G/D7412G allow events to be transmitted to up to four additional SDI Paths.

The D9133TTL-E Network Interface Module (with Ethernet) connects directly to the SDI Bus and occupies SDI Address 88. For additional information regarding the specific programming requirements for enhanced communications, see Sections 2.4 Enhanced Routing and 6.5 Enhanced Communications.

2.3.5Programming a Duplicate Report

To allow an event within a group to report to multiple groups, the event should be Yes for each route number available. For instance, programming Fire Alarms for Route Group 1 and Route Group 2 results in the fire alarms first reporting to Route Group 1 followed by a duplicate report to Route Group 2.

2.3.6Routing Destination Communication Failures

When the R# Primary Device fails to connect with the central station after one or two attempts (see RG# 1 Attempt in Section 6.6.1 Route Group Attempts), the R# Backup Device phone number or SDI Path is attempted. The central station receives the original event with a COMM FAIL PHONE# = (1, 2, 3, or 4) if the R# Primary Device destination is a phone number. If the R# Primary Device is an SDI Path, the central station receives the original event with A COMM FAIL RG# SDI## (SDI Path 1 = 88, SDI Path 2 = 89, SDI Path 3 = 90, SDI Path 4 = 91). When all attempts to both the R# Primary Device and R# Backup Device fail, a Comm Fail RG# Event is generated. Comm Restore Events are not generated.

2.3.7Message Prioritization within a Route Number

The D9412G/D7412G Control Panels meet the digital reporting requirements for UL 864. Fire Alarm Events have the highest priority and are reported first for each group. The next highest priority events are in the following order: panic, duress, medical, intrusion alarm, supervisory, and all troubles and restorals.

	To comply with NFPA and UL864, you
0101	must program Route 1 to report only Fire
	Alarm Events to ensure the fastest
	reporting time.

2.3.8Dialing Attempts

The D9412G/D7412G Control Panels have a prompt called RG# 1 Attempt (see Section 6.6.1 Route Group Attempts.).

If this item is set to No, the control panel first makes up to six attempts to make contact using the primary device within a route group. If unsuccessful, it makes up to four attempts to make contact using the backup device before initiating a Comm Fail Report. When only one destination is programmed, the control panel makes ten attempts to contact that destination. Each group takes approximately 10 minutes to go into Comm Fail.

If this item is set to Yes, the control panel only makes one attempt (instead of two) to contact the primary device before attempting to contact the backup device. The route group still makes a total of ten attempts; however, the R# Primary Device makes five attempts and then the R# Backup Device makes five attempts.

Bosch Security Systems 1/04 47775E