Bosch Appliances D7412G, D9412G manual Passcode/Token Worksheet

D9412G/D7412G Program Entry Guide 3.0 RADXUSR1/RADXUSR2

EN 73

3.0RADXUSR1/RADXUSR2

3.1Passcode/Token Worksheet

These programming items assign user groups 001 to 249 a passcode, area assignment by authority level, and a User Group Window.

	Two handlers in the D5200 Programmer are
0101	used to program the users. RADXUSR1
	Handler programs users 000 to 124.
	RADXUSR2 programs users 125 to 249
	(D9412G only).

3.1.1User Groups

For the D9412G, there are 249 groups (99 groups for the D7412G) consisting of one user with a passcode and token, (master) and three users with tokens/cards but not a passcode (sub-user). All users in the group share the same authority level as the master user.

3.1.2Passcodes

Only the master user is assigned a passcode. The passcode can be three to six digits. Entering three digits in User ### chooses the master user.

Programming the U### Passcode assigns a passcode to the master user. Sub-users cannot use the passcode. While the system allows tokens/cards to be added to USER 0 (service passcode), the tokens/cards do not function because the service passcode uses Authority Level 15.

3.1.3User Group Window

Use U### User Group to enable/disable the U### Passcode for up to eight different time periods throughout the day. Assign the number (1 to

8)programmed in U### User Group to a User Windows #. If the user is outside a window, COMMAND DISABLED appears on the command center after the user enters the passcode and presses [ENTER].

This window does not affect tokens/cards, it only affects the passcode of the master user.

3.1.4Authority Level by Area

A user group is assigned an authority level of 1 through 14 for each area using the U### Area # Auth prompt. The authority level can be different for each area. Not programming an authority level for an area is indicated by the NOT AUTHORIZED display on the command center.

When using the Add/Change User function at the command center, the authority levels and the changes made affect the master user’s passcode and the entire group’s token/cards.

When using the ACCESS CTL LVL function at the command center, the whole group is affected by whether the level is on or off for access control functions only.

When using the DELETE USER? function, the whole group is deleted. There is no means to delete each user within the group individually. It is recommended that you use the ADD/CHG USER? function to change a user token/card instead of deleting the whole group.

3.1.5User Name

Each user group can be assigned one U### Name. This name is logged and reported to the central station for all the users in the group. The user ID is used to differentiate which user’s token/card was executed.

Beginning with v6.30, when using a D1260 Command Center, User 249 text is used for contact information text (such as telephone numbers). If a D1260 is installed on the system, do not use User 249 for user ID information.

3.1.6Tokens/Cards

The master user assigned the passcode can also be assigned a token/card. This is done by programming the U### Mstr Site and U### Mstr C/D.

Three more token/cards are assigned to the user group for sub-users using the U### SU# Site and U### SU# C/D.

3.1.7Reporting and Logging

Modem Format must be Yes for the following reports to the central station. Regardless of the reporting format, they log and print at the local printer as shown. Each sub-user is identified by the master user’s three-digit number plus an extension of 0, 1, 2, or 3. These numbers are called Sub-user ID Codes.

Figure 3 shows all the users for User Group 122 as they would appear.

Bosch Security Systems 1/04 47775E