Manuals / Brands / Household Appliance / Sewing Machine / Brother / Household Appliance / Sewing Machine

Brother BAS-311H E500, E502, E510, E511, E512, E581, E582, E583, E600, E670, LIST OF ERROR CODES, Device-relatederrors, 11.LIST OF ERROR CODES, Data editing-relatederrors

1 92

Download 92 pages, 2.08 Mb

11.LIST OF ERROR CODES

Data editing-related errors

	Code	Cause of error and remedy
	E500	The enlargement ratio setting caused the sewing data to extend outside the sewing area.
	E500	Set the enlargement ratio again.
		Press the RESET key to clear the error.
	E502	The enlargement ratio caused the data pitch to exceed the maximum pitch of 12.7 mm.
	E502	Press the RESET key to clear the error. Set the enlargement ratio again.

	E510	Error in sewing data.
	E510	Press the RESET key to clear the error.
		If an error occurs while reading or revising the sewing data, revise the data.
	E511	No end code has been input into pattern data.
	E511	Press the RESET key to clear the error.
		Press the RESET key to clear the error.
	E512	Number of stitches exceeds allowed maximum.
	E512	Press the RESET key to clear the error.
		Press the RESET key to clear the error.
		Memory switch file cannot be read correctly.
	E581	The model for the data which was read does not match the model being written to.
		Press the RESET key to clear the error. Read data for the same sewing machine model.
	E582	Memory switch versions do not match.
	E582	Press the RESET key to clear the error. Read data for the same version.

	E583	User program versions do not match.
	E583	Press the RESET key to clear the error. Read data for the same version.

	Device-related errors
	Code	Cause of error and remedy
	E600	Upper thread breakage occurred. Thread the upper thread. Re-sewing is then possible.
	E600	Turn off the power, and then check that connector P14 on the main P.C. board is properly connected.

	E670	Problem with the lower thread detector.
	E670	Turn off the power, and then check the lower thread detector.

75

BAS-311H

Contents

Page Page [1] Safety indications and their meanings Indications Symbols [2] Notes on safety Page [3] Warning labels Page 1. NAMES OF MAJOR PARTS 2. SPECIFICATIONS 3. INSTALLATION 4. PREPARATION BEFORE SEWING 5. USING THE OPERATION PANEL 8. SEWING 9. CLEANING 10. STANDARD ADJUSTMENTS LIST OF ERROR CODES TROUBLESHOOTING 1. NAMES OF MAJOR PARTS 2. SPECIFICATIONS 3. INSTALLATION 3-1.Table processing diagram 3-2.Installing the control box 3-3.Installing the oil pan 3-4.Installing the machine head NOTE: Page Page 3-5.Installing the operation panel 3-6.Installing the two-pedalfoot switch <Foot switch operating method 3-7.Connecting the cords < Main P. C. board < Motor P. C. board 3-8.Connecting the ground wire 3-9.Connecting the power cord < Seen from underneath table < EU specifications＞ <200 V system <100 V / 400 V system 3-10.Installing the cotton stand 3-11.Installing the pneumatic unit (pneumatic work clamp specifications) <Adjusting the speed controller 3-12.Installing the eye guard 3-13.Installing the side cover and rear cover 3-14.Lubrication 3-15.Installing the machine head fixing bolt 3-16.Checking the machine head switch <If error [E050], [E051] or [E055] is displayed 4. PREPARATION BEFORE SEWING <Threading mode 4-3.Winding the lower thread CAUTION Adjusting the bobbin winding amount If the thread winds onto the bobbin unevenly 4-4.Installing the bobbin case 4-5-1.Lower thread tension 4-5-2.Upper thread tension 4-6.Starting up Before turning on the power switch, check that the needle bar is at the needle up stop position 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 5. USING THE OPERATION PANEL (BASIC OPERATIONS) 5-1.Name and function of each operation panel item (1) Power indicator (2) CAUTION indicator (3) RESET key (12) SPLIT No. indicator (13) WIPER indicator (14) SELECT key (15) PROGRAM No. display (16) Menu display 5-2.Program setting method 1 Select the item to be changed Change the setting for the parameter Repeat steps 1 to 2 above to record the settings for each parameter 5-2-1.Parameter list Slow start pattern Counter Split No Thread wiping 5-2-2.Using the lower thread counter <Initial value setting <Lower thread counter operation 5-2-3.Using the production counter <Production counter operation 5-2-4.Split number setting method 5-3.Copying programs Press the 2 Switch to program copy mode 3 Select the copying destination program number 4 Copy the program 5-4.Checking the sewing pattern Start continuous test feed mode [Fast-forwardtest mode] [Test interrupt mode] [Paused sewing standby mode] When the setting value for memory switch No. 003 is “2” NOTE: Intermittent presser foot operation 6.USING THE OPERATION PANEL (ADVANCED OPERATIONS) 6.USING THE OPERATION PANEL (ADVANCED OPERATIONS) 6-1.Setting memory switches Change the mode to memory switch setting mode the setting for If you would like to display only the numbers of 6-2.List of memory switch settings Page 6-3.Using cycle programs <Recording method Switch to cycle program recording mode Select a cycle program number Select the program number to be recorded in step Page <Method of use 6-4.Direct selection However, if a program number has nothing recorded, it will not be displayed <Function keys 406 = 0 (Initial setting) 406＝1 6-5.Resetting all settings to their defaults 1 Change to initialization mode [Reference] ALL MEM 7. USING SD CARDS [Read/write mode list] 7-4.Reading additional sewing data Ending read/write mode 8. SEWING Page 9. CLEANING 9-2.Cleaning the control box air inlet ports 9-3.Draining the oil 9-4.Cleaning the eye guard 9-5.Checking the needle 9-6.Lubrication 9-7.Applying grease (Feed mechanism) Page 10. STANDARD ADJUSTMENTS 10-2.Thread take-upspring <Thread take-upspring height <Thread take-upspring tension 10-3.Arm thread guide R 10-4.Adjusting the needle bar height 10-5.Adjusting the timing and the driver needle guard 10-6.Adjusting the needle clearance 10-7.Adjusting the shuttle race thread guide 10-8.Rotary hook lubrication amount 10-9.Adjusting the position of the movable knife Page 10-10.Replacing the movable and fixed knives 10-11.Installing the feed plate 10-12.Adjusting the thread wiper Note: 10-13.Presser foot installation position 10-14.Adjusting the intermittent work clamp <Changing the installation position of stepping clamp link A <Stepping clamp connecting rod position adjustment 10-15.Adjusting the work clamp lift amount <Motor-drivenwork clamp specifications <Pneumatic work clamp specifications 10-16.Adjusting the air pressure (pneumatic work clamp specifications) Page 11. LIST OF ERROR CODES 11.LIST OF ERROR CODES Motor-relatederrors E111 E121 E130 Feed mechanism-relatederrors E200 E201 E204 E205 Work clamp-relatederrors E300 E301 Communication and memory-relatederrors E401 E410 E411 E412 Data editing-relatederrors E500 E502 E510 E511 P.C. board-relatederrors E700 E701 E705 E710 12. TROUBLESHOOTING Lower thread winds to one side Lower thread winding amount is incorrect Thread unraveling at Upper thread is breaking Lower thread is Needle breaks Upper thread is not cut Upper thread is not tight Lower thread is not Poor seam finish on underside of material at 13. 7-SEGMENTDISPLAY LIST MEMO