Saved System Messages | Cabletron Systems TRXI-24, TRXI-22, TRXI-42

TESTING AND TROUBLESHOOTING

4.3.4Saved System Messages

Saved System Message are device related start-up or boot strap messages, BOOTP/TFTP host, or start-up error messages. To access the Saved System Messages queue, you must ﬁrst enter the Saved Alarm Messages queue. While in the Alarm Messages queue, press the Display button and hold for ﬁve seconds. You can scroll through each message by pressing the Display button. If you do not press the Display button for ten seconds, the LCD defaults to the product name.

Displayed Message
TFTP Host	TFTP File
xxx.xxx.xxx.xxx	xxxxxxxxxxxxxxxx
Last TFTP Host	Last TFTP File
xxx.xxx.xxx.xxx	xxxxxxxxxxxxxxxx
BootP Host
xxx.xxx.xxx.xxx

Page 4-7

Image 54

Cabletron Systems TRXI-24, TRXI-22, TRXI-42, TRXI-44 manual Saved System Messages, Displayed Message

Contents

Token Ring Intelligent HUB USER’S Guide Printed On Recycled Paper FCC Notice Exclusion of Warranty and Disclaimer of Liability Contents Table of Contents Introduction REQUIREMENTS/SPECIFICATIONSInstallation Contents Testing and TroubleshootingLocal Management Using this Manual Chapter Introduction Introduction Getting Help Trxi Overview Trxi Features Group Subgroup Section Media Type ConnectorRmon MIB Support Token Ring Port Interface Modules TPIMs Remote Network Management Capabilities Flash EEPROMsCabletron’s Distributed LAN Monitor Recommended Reading Chapter REQUIREMENTS/SPECIFICATIONS Cable Specifications Attenuation and Impedance Frequency Impedance Attenuation Type 3 Media Filters Maximum Lobe LengthsUTP Cable Type Maximum Lobe Length Mbps Maximum Number of Stations REQUIREMENTS/SPECIFICATIONS STP Cable Type Ring Speed Mbps Maximum Trunk Lengths Mixed Cable Types Multimode Fiber Optic Cable Speciﬁcations for the TPIM-F2 Cable Type Attenuation Maximum Drive DistanceFiber Optic Budget Single Mode Fiber Optic Cable Speciﬁcations for the TPIM-F3 Temperature CrosstalkNoise REQUIREMENTS/SPECIFICATIONS Modem REQUIREMENTS/SPECIFICATIONS COM 1/COM 2 Port SpecificationsConsole UPS REQUIREMENTS/SPECIFICATIONS Tpim Specifications TPIM-T1 REQUIREMENTS/SPECIFICATIONS TPIM-T2 TPIM-T4 REQUIREMENTS/SPECIFICATIONS TPIM-F2 Parameter Typical Worst Worst Case TypicalValue Case Budget REQUIREMENTS/SPECIFICATIONS TPIM-F3 TPIM-F3 Parameter Typical Minimum Maximum Output Min. Load Max. Load Max Power REQUIREMENTS/SPECIFICATIONS General SpecificationsPower Supply Requirements Environmental Requirements REQUIREMENTS/SPECIFICATIONS Safety ServicePhysical Unpacking the Trxi Attaching the Strain Relief Bracket Installing the Trxi Attaching the Strain Relief Installing the Trxi in the Rack Rack Mounting the Trxi Wall Mounting the Trxi Free-Standing Installation Installation Setting the Ring Speed Switch Ring Speed Switch Settings Installation Setting the Nvram Switch Installation Connecting the Trxi to the Power Source Connecting the Network Lobe Port Cabling Configuration Examples for TRXI-24 and TRXI-44 LNK TPIM-T4 Installation Installing the Tpim RI/RO Modules Setting the TPIM’s Phantom Switch and RI/RO Switch Top View Installing a Tpim to the Trxi 12. Installing a Tpim Connecting a Twisted Pair Segment to the TPIM-T1 Connecting a Twisted Pair Segment to the TPIM-T2 or TPIM-T4 Installation LNK Finishing the Installation Chapter Testing and Troubleshooting Checking the Installation Testing and Troubleshooting Using Lanview TRXI-24TOKEN Ring HUB with Lanview Testing and Troubleshooting LCD Display LCD Static System Messages Displayed Message Comments Alarm Messages Displayed Messages Comments Failure or Error Messages Unsaved Initialization MessagesNormal Unsaved Initialization Messages Saved System Messages Displayed Message Chapter Local Management Local Management Management Terminal Requirements Attaching the Management Terminal General Setup Setting the Management Terminal Setup ParametersDisplay Setup Setup Modem Cable Conﬁguration and Setup RJ45 COM 2 Port Local Management Accessing Local Management Trxi Local Management Local Management Using Local Management Main Menu Selecting a Menu Option Exiting a Local Management ScreenExiting Your Local Management Session System Time System Level ScreenSystem Date IP Address COM 2 Application Setting the System DateCOM 1 Application Clear All Nvram Setting the System Time Setting the IP Address Setting the Subnet Mask Setting the Clear All Nvram Field Setting the Enable Beacon Recovery Field Snmp Community Names Screen Community Name AccessComponent Name Editing the Community Name Field Trap Destination Enable TrapsSnmp Traps Screen Trap Community Name Setting Snmp Traps Ring Security Screen Security Mode Station AddressStn Edit Previousscreen SAVE/EXECUTENextscreen Return Building the Allowed List Adding Stations to the Station Address Allowed List Changing the Ring Security Mode Deleting Stations from the Station Address Allowed List Device Statistics Screen Device StatisticsInterface Isolating Errors Ring Information Lost Frame Errors Ports EnabledNON-ISOLATING Errors Ring Number Token Errors Frame Copied ErrorsRcvr Congestion Errors Frequency Errors Selecting the Device Statistics Counter Mode Setting the Refresh Field Port Status Enable All PortsChassis Status View Screen Temp Operational Setting the Enable All Ports OptionSetting the Operational/Administrative Mode Option Return Component Status View Screen 11. Component Status View Screen Snmp Tools Screen Getnext GETSET Walk Security Access Level Getting and Setting OIDsCommunity Name Local Management Scrolling Through MIB OIDs Local Management Local Management Spanish Power Supply CordGerman French