AP-Manager Interface, Virtual Interface | Cisco Systems 3.2 specification

Chapter 3 Configuring Ports and Interfaces

Configuring the Management, AP-Manager, Virtual, and Service-Port Interfaces

AP-Manager Interface

•VLAN identifier

Note Enter 0 for an untagged VLAN or a non-zero value for a tagged VLAN. Cisco recommends that only tagged VLANs be used on the controller.

•Fixed IP address, IP netmask, and default gateway

Note The AP-manager interface’s IP address must be different from the management interface’s IP address but must be on the same subnet as the management interface.

•Physical port assignment

•Primary and secondary DHCP servers

•Access control list (ACL) name, if required

Note To create ACLs, follow the instructions in Chapter 5.

Virtual Interface

•Any fictitious, unassigned, and unused gateway IP address, such as 1.1.1.1

•DNS gateway host name

Service-Port Interface

Note The service-port interface uses the controller’s factory-set service-port MAC address.

•DHCP protocol (enabled) or

•DHCP protocol (disabled) and IP address and IP netmask

Step 4 Click Save Configuration to save your changes.

Step 5 If you made any changes to the virtual interface, reboot the controller so your changes take effect.

Cisco Wireless LAN Controller Configuration Guide

	OL-8335-02	3-11

Image 67

Cisco Systems 3.2 manual AP-Manager Interface, Virtual Interface, Service-Port Interface

Contents

Corporate Headquarters Cisco Wireless LAN Controller Configuration Guide Cisco Wireless LAN Controller Configuration Guide Iii N T E N T S Client Location Enabling Web and Secure Web Modes Configuring Ports Vii Configuring the System for SpectraLink NetLink Telephones Viii QoS-Level5-17 ACL-Name5-17 Interface-Name5-18 VLAN-Tag5-18 Using Dhcp Option 43 Radio Resource Monitoring Prerequisites Xii Series Wireless LAN Controllers B-8 Xiii Preface Xiv AudiencePurpose Organization Conventions Xvi Xvii Related PublicationsObtaining Documentation Cisco.com Xviii Documentation FeedbackProduct Documentation DVD Ordering Documentation Cisco Product Security Overview Reporting Security Problems in Cisco ProductsXix Obtaining Technical Assistance Submitting a Service RequestCisco Technical Support & Documentation Website Obtaining Additional Publications and Information Definitions of Service Request SeverityXxi Xxii Overview Cisco Wireless LAN Solution Overview Single-Controller Deployments Cisco Wlan Solution Components Single-Controller Deployment Multiple-Controller Deployments Operating System Security Operating System Software Cisco Wlan Solution Wired Security Operational Requirements Cisco Wireless LAN ControllersConfiguration Requirements Layer 2 and Layer 3 Lwapp Operation Inter-Controller Layer 2 Roaming Client RoamingPrimary, Secondary, and Tertiary Controllers Same-Subnet Layer 2 Roaming Client Location Inter-Subnet Layer 3 RoamingSpecial Case Voice Over IP Telephone Roaming Security Considerations Per-Wireless LAN AssignmentExternal Dhcp Servers Per-Interface Assignment Cisco Wlan Solution Wireless LANs Cisco Wlan Solution Wired Connections Identity Networking Access Control Lists Enhanced Integration with Cisco Secure ACS File Transfers Pico Cell Functionality Power over Ethernet Wireless LAN Controller Platforms Intrusion Detection Service IDS Cisco 4100 Series Wireless LAN Controllers Cisco 2000 Series Wireless LAN Controllers Cisco 2000 Series Wireless LAN Controller Model Numbers Cisco 4400 Series Wireless LAN Controllers Cisco 4400 Series Wireless LAN Controller Model Numbers Cisco 4100 Series Wireless LAN Controller Model Numbers Startup Wizard Cisco Wireless LAN Controller Failover Protection Cisco Wireless LAN Controller Memory Network Connections to Cisco Wireless LAN Controllers Cisco Wireless LAN Controller Automatic Time SettingCisco Wireless LAN Controller Time Zones Cisco 4100 Series Wireless LAN Controllers Cisco 2000 Series Wireless LAN Controllers 6shows connections to the 4100 series controller Cisco 4400 Series Wireless LAN Controllers Rogue Access Points Web User Interface and the CLI Rogue Access Point Location, Tagging, and ContainmentWeb User Interface Command Line Interface Using the Web-Browser and CLI Interfaces Enabling Web and Secure Web Modes Using the Web-Browser InterfaceGuidelines for Using the GUI Configuring the GUI for Https Show certificate summary Loading an Externally Generated Https Certificate Web Administration Certificate file webadmincertname.pem Logging into the CLI Using the CLIUsing Online Help Disabling the GUI Using a Remote Ethernet Connection Using a Local Serial Connection Logging Out of the CLI Command ActionNavigating the CLI Enter config network mgmt-via-wireless enable Configuring Ports and Interfaces Ports Overview of Ports and Interfaces Distribution System Ports Service Port Management Interface Interfaces Virtual Interface AP-Manager Interface Dynamic Interface Service-Port Interface Ports, Interfaces, and WLANs WLANs Configuring Ports and Interfaces Interfaces Management Interface AP-Manager Interface Service-Port InterfaceVirtual Interface Using the CLI to Configure the AP-Manager Interface Using the CLI to Configure the Management InterfaceConfig interface acl management access-control-list-name Config interface acl ap-manager access-control-list-name Using the CLI to Configure the Virtual Interface Using the GUI to Configure Dynamic Interfaces Configuring Dynamic InterfacesUsing the CLI to Configure the Service-Port Interface Interfaces New Using the CLI to Configure Dynamic Interfaces Ports Configuring Ports Controller Available Data Rates Parameter Description Default Auto Default EnableController Supported Data Rates Configuring Port Mirroring Configuring Spanning Tree Protocol STP State Description Using the GUI to Configure Spanning Tree Protocol STP Mode Description Default OffDefault 10 Controller Spanning Tree Configuration Range Default Default DisableRange Default 2 seconds Using the CLI to Configure Spanning Tree Protocol 11illustrates LAG Enabling Link Aggregation Link Aggregation Guidelines 12 Link Aggregation with Catalyst 6500 Neighbor Switch 13 General Using the GUI to Enable Link Aggregation Configuring Neighbor Devices to Support LAG Using the CLI to Enable Link Aggregation Using Multiple AP-Manager Interfaces Using Link Aggregation 14 Two AP-Manager Interfaces Examples 15 Three AP-Manager Interfaces 16 Four AP-Manager Interfaces 17 Interfaces New Connecting Additional Ports Configuring Controller Settings Before You Start Using the Configuration Wizard Browse to the Commands/Reset to Factory Defaults Resetting the Device to Default SettingsResetting to Default Settings Using the CLI Resetting to Default Settings Using the GUI Running the Configuration Wizard on the CLI Managing the System Time and Date Configuring a Country CodeConfiguring Time and Date Manually Configuring NTP Country Code Bands Allowed Enabling and Disabling 802.11 Bands Configuring Radius Settings Configuring Administrator Usernames and PasswordsConfiguring Snmp Settings Enabling System Logging Enabling Dynamic Transmit Power ControlConfig 802.11a 802.11bg dtpc enable disable Enabling 802.3x Flow Control Understanding Multicast Mode Configuring Multicast ModeGuidelines for Using Multicast Mode Enabling Multicast Mode Configuring the Supervisor 720 to Support the WiSMCommand Multicast Mode Command Purpose Configuring the SupervisorGeneral WiSM Guidelines Interface GigabitEthernet9/5-8 Switchport mode trunk Channel-group 1 mode onWism service-vlan vlan Interface GigabitEthernet9/1-4 Service-module wlan-controller 1/0 reset Using the Wireless LAN Controller Network Module OL-8335-02 Configuring Security Solutions Security Overview Cisco Wlan Solution SecurityLayer 1 Solutions Layer 2 Solutions Tagging and Containing Rogue Access Points Layer 3 SolutionsRogue Access Point Solutions Rogue Access Point Challenges Integrated Security Solutions Configuring the System for SpectraLink NetLink Telephones Using the CLI to Enable Long Preambles Using the GUI to Enable Long Preambles Using the GUI to Enable Management over Wireless Using Management over Wireless Using the CLI to Enable Management over Wireless Configuring DhcpUsing the GUI to Configure Dhcp Config wlan enable wlan-id Customizing the Web Authentication Login ScreenUsing the CLI to Configure Dhcp Config wlan disable wlan-id Typical Web-Browser Security Alert Default Web Authentication Operation Typical Web Authentication Login Window Hiding and Restoring the Cisco Wlan Solution Logo Customizing Web Authentication OperationChanging the Web Authentication Login Window Title Clear webmessage Config custom-web webmessage messageChanging the Web Message Changing the Logo Downloading the Logo or Graphic Config custom-web redirecturl url Verifying Web Authentication ChangesCreating a Custom URL Redirect Example of a Customized Web Authentication Login Window Example Sample Customized Web Authentication Login Window Identity Networking Overview Configuring Identity Networking QoS-Level Radius Attributes Used in Identity NetworkingACL-Name VLAN-Tag Interface-Name Tunnel Attributes OL-8335-02 Configuring WLANs Configuring Wireless LANs Wireless LAN OverviewDisplaying, Creating, Disabling, and Deleting Wireless LANs Enabling MAC Filtering Activating Wireless LANsAssigning a Wireless LAN to a Dhcp Server Configuring MAC Filtering for Wireless LANs Dynamic 802.1X Keys and Authorization Assigning Wireless LANs to VLANsConfiguring Layer 2 Security Configuring a Timeout for Disabled Clients Dynamic WPA Keys and Encryption WEP Keys IPSec Configuring Layer 3 SecurityConfiguring a Wireless LAN for Both Static and Dynamic WEP IPSec Authentication IKE Diffie-Hellman Group IKE AuthenticationIKE Phase 1 Aggressive and Main Modes IKE Lifetime Timeout Local Netuser Configuring Quality of ServiceWeb-Based Authentication IPSec Passthrough Ieee 802.11e UP Configuring QoS Enhanced BSS QbssConfig wlan wmm disabled allowed required wlan-id Traffic Type Config wlan 7920-support client-cac-limit enable wlan-id Enabling 7920 Support Mode Controlling Lightweight Access Points Cisco 1000 Series Ieee 802.11a/b/g Lightweight Access Points Lightweight Access Point Overview Typical 1030 Lightweight Access Point Configuration Cisco 1030 Remote Edge Lightweight Access Points Cisco 1000 Series Lightweight Access Point Part Numbers External Antenna Connectors Cisco 1000 Series Lightweight Access Point LEDsAntenna Sectorization Cisco 1000 Series Lightweight Access Point Connectors Cisco 1000 Series Lightweight Access Point Mounting Options Using the DNS for Controller DiscoveryCisco 1000 Series Lightweight Access Point Monitor Mode Dynamic Frequency Selection Reverting from Lightweight Mode to Autonomous Mode Autonomous Access Points Converted to Lightweight Mode Using a Controller to Return to a Previous Release Access Point VCI String Using Dhcp Option Config ap get-radio-core-dump slot ap-name Converted Access Points Send Radio Core Dumps to ControllerEnabling Memory Core Dumps from Converted Access Points Display of MAC Addresses for Converted Access Points Config ap static-ip enable ap-name ip-address mask gateway Config ap reset-button enable disable ap-nameall OL-8335-02 Managing Controller Software Configurations Upgrading Controller Software Transferring Files to and from a Controller Transfer download path absolute-tftp-server-path-to-file Clearing the Controller Configuration Saving ConfigurationsErasing the Controller Configuration Resetting the Controller OL-8335-02 Configuring Radio Resource Management Radio Resource Monitoring Overview of Radio Resource Management Dynamic Channel Assignment Coverage Hole Detection and Correction Dynamic Transmit Power ControlClient and Network Load Balancing RRM Benefits Overview of RF GroupsRF Group Leader RF Group Name Configuring an RF Group General Using the GUI to Configure an RF Group Using the GUI to View RF Group Status Using the CLI to Configure RF GroupsViewing RF Group Status Global Parameters Global Parameters Auto RF Auto Using the CLI to View RF Group Status Using the GUI to Enable Rogue Access Point Detection Enabling Rogue Access Point Detection All APs Details AP Authentication Policy Using the CLI to Enable Rogue Access Point Detection Configuring Dynamic RRM Default Enabled Using the GUI to Configure Dynamic RRMRF Group Channel Assignment Method Description Default AutomaticYou click Invoke Channel Update Now RF Channel Assignment Default Disabled Click Invoke Power Update Now Tx Power Level AssignmentAssignment Method Description Default 25% Default 10%Default -70 dBm Default 80% Monitor Intervals Default Noise/Interference/Rogue Monitoring Channels Config 802.11a disable Config 802.11b disable Using the CLI to Configure Dynamic RRM Overriding Dynamic RRM Radios Cisco APs Configure Config 802.11a txPower AP1 Config 802.11a disable Config 802.11b disable Viewing Additional RRM Settings Using the CLI 10-1 Configuring Mobility Groups 10-2 Overview of Mobility Inter-Controller Roaming 10-3 Inter-Subnet Roaming 10-4 10-5 Overview of Mobility Groups Two Mobility Groups 10-6 10-7 Configuring Mobility GroupsDetermining When to Include Controllers in a Mobility Group Prerequisites 10-8 Using the GUI to Configure Mobility Groups Mobility Group Member New 10-9 Mobility Group Members Edit All 10-10 Using the CLI to Configure Mobility Groups Configuring Auto-Anchor Mobility10-11 Using the GUI to Configure Auto-Anchor Mobility Guidelines for Using Auto-Anchor Mobility10-12 WLANs 10-13 10-14 Using the CLI to Configure Auto-Anchor Mobility Safety Considerations Translated Safety Warnings Bewaar Deze Instructies Safety Considerations Avvertenza Importanti Istruzioni Sulla Sicurezza Warnung Wichtige Sicherheitshinweise Guarde Estas Instruções Aviso Instruções Importantes DE Segurança Class 1 Laser Product Warning Aviso Produto a laser de classe Ground Conductor Warning Cisco Wireless LAN Controller Configuration Guide Chassis Warning for Rack-Mounting and Servicing Cisco Wireless LAN Controller Configuration Guide Cisco Wireless LAN Controller Configuration Guide OL-8335-02 Cisco Wireless LAN Controller Configuration Guide Page OL-8335-02 Page OL-8335-02 Page Battery Handling Warning for 4400 Series Controllers Cisco Wireless LAN Controller Configuration Guide OL-8335-02 Equipment Installation Warning Cisco Wireless LAN Controller Configuration Guide OL-8335-02 OL-8335-02 Cisco Wireless LAN Controller Configuration Guide OL-8335-02 Cisco Wireless LAN Controller Configuration Guide Cisco Wireless LAN Controller Configuration Guide OL-8335-02 OL-8335-02 Declarations of Conformity and Regulatory Information Manufacturer Regulatory Information for 1000 Series Access PointsModel FCC Certification number Canadian Compliance Statement Department of Communications-CanadaCertification number EMC Declaration of Conformity for RF Exposure 03-5549-6500 All Access Points Access Points with Ieee 802.11a Radios Declaration of Conformity Statements Cisco Wireless LAN Controller Configuration Guide OL-8335-02 OL-8335-02 End User License and Warranty End User License Agreement Cisco Wireless LAN Controller Configuration Guide OL-8335-02 Limited Warranty Appendix C End User License and Warranty Limited Warranty Disclaimer of Warranty Additional Open Source Terms OL-8335-02 System Messages and Access Point LED Patterns System Messages Error Message Description Lradifcurrentchannelchanged Client Reason Codes Using Client Reason and Status Codes in Trap LogsClient Reason Code Description Meaning Client Status Code Description Meaning Client Status Codes LED Conditions Status Using Lightweight Access Point LEDs IN-1 Numerics IN-2 IN-3 DFS Dhcp IN-4 Help Hold Time parameter IN-5 IN-6 IN-7 IN-8