Powering the IP Camera On or Off | Cisco Systems 4300 specification

Chapter 2 Getting Started

Powering the IP Camera On or Off

To adjust the back focus, perform the following steps while viewing video from the camera. For information about viewing video, see Chapter 4, “Viewing Live Video.”

Procedure

Step 1 With a lens attached to the IP camera, use the 0.9mm Allen wrench that is supplied with the IP camera to loosen the focus ring hex screw.

This screw is on the bottom of the camera just behind the focus ring.

Step 2 Adjust the back focus by aiming the IP camera at an object that is at least 15 feet (4.5 meters) away and rotating the focus ring to obtain a clear image as follows:

•For a variable-focus lens, obtain a sharp picture in both wide-angle and telephoto positions.

•For a zoom lens, ensure that the object of interest remains in focus throughout the entire zoom range of the lens.

Step 3 Use the Allen wrench to tighten the focus ring hex screw.

Powering the IP Camera On or Off

The IP camera does not include an on/off switch. You power it on or off by connecting it to or disconnecting it from a power source. When you power off the IP camera, configuration settings are retained.

To power on the IP camera, take either of these actions:

•Use an STP (shielded twisted pair) Category 5 or higher network cable to connect the IP camera to a network switch that provides 802.3af compliant PoE

•Use an optional 12 VDC or 24VAC power adapter to connect the IP camera to a wall outlet

To power off the IP camera, take either of these actions:

•If the IP camera is receiving PoE, disconnect the network cable

•If the IP camera is receiving power through the power adapter, unplug the adapter from the wall or disconnect it from the camera

Resetting the IP Camera

You reset the IP camera by pressing the Reset button on the rear of the device (see Figure 1-3 on page 1-5). There are various reset types, as described in Table 2-4.

You also can also perform these reset operations from the Maintenance Settings window as described in the “Maintenance Settings Window” section on page 3-29.

	Cisco Video Surveillance 4300 and 4500 High-Definition IP Cameras User Guide
2-10	OL-19609-04

Image 22

Cisco Systems 4300 manual Powering the IP Camera On or Off, Resetting the IP Camera

Contents

Americas Headquarters Text Part Number OL-19609-04 Copyright 2009-2011 Cisco Systems, Inc. All rights reserved N T E N T S Log Windows Overview Organization Preface IP Camera Features Overview IP Camera Physical Details Adjusting Back Focus on the IP Camera section on Front of IP Camera Rear of IP Camera Described in the Resetting the IP Camera section on Side of IP Camera DC Auto Iris Lens Connector Pinouts Package Contents Installing the IP Camera Getting Started Action Explanation Action Explanation Action Explanation Procedure Performing the Initial Setup of the IP CameraBefore you Begin Accessing the IP Camera Protocol//ipaddress Understanding the IP Camera User Interface IP Camera Window Links Link Description IP Camera WindowsField Description IO Port Status Adjusting Back Focus on the IP CameraLAN IP Channel 1 and Channel Powering the IP Camera On or Off Resetting the IP Camera Initial Setup of the IP Camera Reset Type Procedure RemarksSection on OL-19609-04 Configuring and Managing the IP Camera Accessing Navigating the Configuration Windows Feature Setup Windows Snmp Resolution Primary fps Secondary fps Streaming Settings WindowStreaming Option Description Streaming Setup AreaCurrent Channel Area Audio Setup Area Video Area Video Adjustments Area Camera Settings WindowMicrophone Area Described in , Viewing Live Video Day Night Filter Area Text Overlay Area Video Overlay Settings WindowIO Ports Settings Window IO Ports Input Ports Area Pan Tilt Settings WindowOutput Ports Event Notification Window RS-232 SettingsPan/Tilt Area Event Triggering Area Option Email Notification Area Patrol Sequence Window Patrol Sequence Area Basic Settings Window Network Setup WindowsAnalytics Windows IP Addressing Window Basic Settings AreaBasic Device Operations Area Time Settings Window IP Addressing Area Local Time Area Set Time Mode AreaYou click Save Settings Clone PC Time button Cisco Discovery Protocol CDP Area Discovery Settings WindowNTP Server Settings Area Show Neighbors button Snmp v2c Area Snmp Settings WindowSnmp v3 Area 8000000901IPv4addresshex 802.1x Settings Window EAP-PEAP Configuration Options IP Filter Settings WindowEAP-FAST Configuration Options IP Filter Area QoS Settings WindowClass of Service CoS Area Filter Entries Area Differentiated Services DiffServ Area Administration WindowsAccount Initialization Window Access Protocols Area Administrator Accounts AreaSSH User Settings Window User List Area Change button Maintenance Settings WindowDelete button Reset button Factory Default AreaRestore button Reboot Area Reboot button Addressing Window section on Firmware Settings WindowDevice Information Area Device Processes Window Firmware Maintenance AreaUpgrade button Details button Log Setup Settings Window, Local Log Window, Password Complexity WindowLog Setup Settings Window Log Windows Local Log Settings Area Syslog Settings Area Local Log Window Log List Area Log messages, see -25 on Explanation Severity Devicerebootmanual DefaultsrestoredDevicerebootauto Ethsignaldegrade Outputtworeset LoginOutputonereset Powersupplyfailure Startstream TimedstswitchTimeregswitch Stopstream Control Description Video controls Streaming Settings Window section on Video image controls Save Snapshot button Image tools Hotspot Zoom buttonHotspot Pan/Tilt Mirror button Full Screen button Audio controls Add Preset Position Presets controlsSet Current Preset as Preset button Pan/tilt speed controls Motion detection Motion detection controls Enable Motion Detection check box Save Settings button Full Screen check Troubleshooting Troubleshooting Numerics IN-2 Http Https LED IN-4 IN-5 IN-6 IN-7 IN-8