5.0A/V Controller Owner’s Manual
Staple or clip your original bill of sale here.Û
Table of Contents
Citation
Table of Contents continued
Introduction
Introduction
Safety Information
Important Safety Information
•Avoid moist or humid locations
Safety Information
Unpacking
Safety Information
Typographic Conventions
Quick-StartInstructions
Quick-StartInstructions
Quick-StartInstructions
Quick-StartConnection and Setup
Analog
Quick-StartInstructions
Listen Programs listing
Quick-StartInstructions
Front Panel Controls & Indicators
Front Panel Controls and Indicators
3 4 5
7Mute Button: Press this button to temporarily reduce or silence the audio output. Press the button again, or change the volume level to return to normal operation. Note that when the Mute function is activated, the level at the Record Outputs £ and Remote Zone ª will remain uninterrupted. When Mute is engaged, a reminder message will appear in the on-screendisplay see figures OSD-20and OSD-21on page 47 and the word Mute will replace the volume level indication in the Information Display !. The actual level for the system when the Mute function is engaged may be set through the System Options Menu see page
Front Panel Controls & Indicators
Rear Panel Connections
Rear Panel Connections
Rear Panel Connections
¢Front Channel Audio Outputs: Connect these jacks to the inputs of the audio power amplifier feeding the front left and right speakers
¡S-VideoMain Output: Connect this jack to the main video display device that will be used to view the output of the source selected by the
Rear Panel Connections
Remote Control Operation
Remote Control Operation
¶ • º Œ
Main Portion of Remote
Remote Control Operation
Lower Portion of Remote
Cancel: This button has two functions. Its main use is to exit from the menus and return either to normal operation or to the previous menu when configuring the 5.0 or adjusting system parame- ters. Within some menus, the Cancel button will have specific “exit” functions that are shown on screen at the appropriate time. Pressing this button when the unit is in normal operating modes and no other menu is present will reset all user parameters
Remote Control Operation
QDigital Input Program Buttons: Press any of these buttons to select any of the six digital input programs. Note that the numbers on the buttons DO NOT refer to the equipment connected to any of the individual analog input jacks on the rear of the 5.0. These numbers call up the complete input profile that is established using the Programs Setup Menu to combine any of the digital sources with any video input. See pages 37–40for more information on configuring the input programs
Remote Control Operation
System Installation
System Installation
Input Connections
Audio Inputs
System Installation
Video Inputs
System Installation
Output Connections
System and Accessory Inputs
Audio Outputs
Citation 5.0 A/V Controller
System Installation
Video Outputs
System Installation
Record Outputs
Remote Zone Outputs
System Accessory Connections
System Installation
Additional Amplifiers
System Installation
System Configuration
Speaker Selection and Placement
System Configuration
System Configuration
Figure 6 Speaker Placement, Side View
System Configuration
Initial Turn-On
Figure OSD-1
RESET
Speaker Setup
System Configuration
Citation
System Configuration
is installed
System Configuration
•Select NONE when no subwoofers are installed
<Ð Exit Menus <Ð appears
System Configuration
Figure OSD-5
Figure OSD-6
Figure OSD-7
System Configuration
System Configuration
Program Setup
Figure OSD-8
System Configuration
The second line, just below the line indicating how to return to the “Main Menu,” contains the program number. Remember that this number only defines the sources and conditions that you attach to it in the following steps. It DOES NOT refer to any specific input connection on the 5.0’s rear panel
once so that Input
System Configuration
System Configuration
System Options
jack â on the rear panel, or both
System Configuration
Figure OSD-11
System Configuration
Configuration
Editing Watch and Listen Lists
System
Turning On and Off
Operating the Citation
Operating the Citation
POWER OFF STANDBY
Source Selection
Operating the Citation
Prog 7 : DVD Pro Logic* Vol=49
Citation
Setting the Volume Level
Operating the
MASTER VOLUME =
Setting the Balance and Level Trims
Operating the Citation
Operating the Citation
Output Level Adjustment Trims
Figure OSD-22
Figure OSD-23
Operating the Citation
Secondary Remote Controls
Figure OSD-24
Operating the Citation
Surround Modes
Figure OSD-25
Operating the Citation
Movie Modes vs. Music Modes
and music
Operating the Citation
Surround Mode Definitions
Selecting Surround Modes
Movie Modes
Music Modes
Operating the Citation
Viewing System Status
Viewing the Digital Mode Status
Operating the Citation
Figure OSD-26
Advanced Features
Advanced Features
Customizing Surround Modes
The next line down is Mode Type. Press the Û Menu Control button one more time to reach this line, but do note that if you have chosen either Dolby or 6-Axis on the line above Mode Button, you cannot move below the Mode Button line. This is to preserve their factory settings when they are selected by their dedicated buttons
Advanced Features
Customizing Digital Sources
Advanced Features
Figure OSD-30
Advanced Features
Remote Zone
Setting Up the Remote Zone
Advanced Features
System Reset
Figure OSD-32
Advanced Features
Figure OSD-33
Figure OSD-34
Figure OSD-37
Advanced Features
Figure OSD-38
Figure OSD-39
Troubleshooting Guide
Troubleshooting Guide
Appendix A
Appendix A Factory Presets
Page
DIGITAL INPUT MODE MAP Default Settings
ANALOG INPUT MODE MAP Default Settings
Appendix A
Appendix B
Appendix B User Worksheets
Auto
Service Information
Service Information
Specifications
Specifications
Figure Index
Figure Index
Figure
Figure
Limited U.S. and Canadian Warranty
Limited U.S. and Canadian Warranty
Madrigal Audio Laboratories, Inc P.O. Box
Citation
Middletown, CT Manufactured in USA
Part #