Email Notification | Clover Electronics CDR1650 guide

Stand-alone DVR Instruction Manual

7-7.8. EMAIL NOTIFICATION

▫Email notification enables to notify events (sensor, motion, video loss, power on/off, power loss, record on/off, record fail, replay or copy start/stop) by sending emails to one or two email accounts.

[Fig.7-108 Email Notification window]

124

Image 124

Clover Electronics CDR1650 instruction manual Email Notification window

Contents

Digital Video Recorder Page Contents System Disk Manager 133 158 Page About this manual Page Unpacking Stand-alone DVR Digital Video Recorder Unit Features Page What to do at the time of Installation Stand-alone DVR should be installed in the following orderPage Specifications Page Installation Controls and Connectors For 8Ch & 16Ch DVR Rear Page System Connection Installation Camera Connection Connection of Normal CamerasConnection of Loop Output Monitor Connection Connection of Main Monitor Pin configuration of VGA Connector VGA Monitor Connection Sensor Connection and Relay in &OUT Sensor Connection Sensor Relay OUT Connection 4. RS232C, RS485, RS422 Connection Installation Power Connection How to operate Copying the Recorded Data During Replaying General Information Operating Interface IR Remote Controller 1IR Remote Controller Power On/Off Power on On the front panel or the remote controllerPower OFF On the front panel or the remote controller By clicking the mouse Appearance or Disappearance of Power Button 1 Power & Audio buttons Menu Bar On/Off Live Screen Display Screen Full Screen Split Screens Full Screen Sequencing Screen Quad Screen Split Screen2page Sequencing Screen Screen Live Display pop-up screen Sequencing Screens Live Menu Display pop-up window Live Audio Audio buttons Zoom 10 Zoomed screen OSD on /OFF is possible in the Live mode or Record mode OSD on / OFF PAN / Tilt 13 PAN/TILT button Channel Selection and Screen Conversion Zoom / FocusButton of PAN/TILT Control window PAN / Tilt Preset Setup PresetPreset Execution System Status 16 System Status button Power Loss Lists Power Loss Lists 19 Power Loss Lists Message Video Loss List 20 Video Loss Lists window 22 Video Loss Lists Message window Manual Continuous recording RecordManual Event Recording Timer Recording 24 Manual Event Recording setup Timer Event Recording 26 Timer Event Recording setup Recording Icons 28 Recording Icons Quick Replay Replay Playback Devices Set the Start Time By using the Replay Time set-up buttons By using the Replay Time set-up bar How to Operate ② Play / Pause ③ REW/FF ④ Prev / Next Disappearance of Replay control buttons 36 Split screen during replaying Copy Copying devices Regards to blank Medias CD-R/W and DVD-R/W Set the Copy Start Time Copying extent By using the Copy Start/End set-up buttons 40 Copy Start time and Channel Selection window By using the Start/End set-up bar Set the Copy End Time Copying extent 43 Start Copy Time Setup window Copying the recorded data during replaying Select Copy Mode Network CopyUSB Copy CD-RW Copy DVD-RW Copy 45 Copying IconPage Setup Audio Recording ON/OFF Microphone Volume Setup Setup Setup Icon on Main Menu System Time / Date Time Format Date Format Display Factory Default 10 System Config Load Config / Backup Config Load Config Backup Config 14 Load Config window Password Change PasswordON/OFF IR Remote ID DVR IR ID Number Firmware Update By USB memoryBy DVR Master GUI System Info Disk Manager HDD Overwrite HDD Write FailFormat 25 HDD Format window Camera Camera ON/OFF Camera Name Camera Title Buzzer Relay Pan/Tilt Settings PTZ ID 34 PAN/TILT & Remote 38 Baudrate button 42 Stop Bits button Display Sequencing dwell time Audio Microphone VolumeAudio Recording ON/OFF Record Record Icon Display All Manual / Timer recording button 54 All Manual / Timer button All Motion on / OFF, Sensitivity and Velocity Setting 56 All Motion Setup button Size Recording Resolution All Sensors on / OFF Recording Speed 63 Record Speed button Recording Quality 65 Recording Speed for each channel Timer Recording Schedule Recording Recording ModeManual Recording 105 106 73 Spot Setup button By All Set 108 By Window Set 78 Window SET button 110 By Each Cell 82 Each Cell button 112 Recording by Sensor PIR Sensor 86 Sensor window 114 115 Network 93 IP Mode button GATEWAY, SUBNET, IP Address 97 Port Setup window Port MAC ID Disable / EnableMNS MAC Name Server IP Address / Port Site Name Ddns Dynamic Domain Name System 103 Ddns menu Host Name PasswordUser ID HOW to Setup and USE the Ddns 7-7.7.1. Router Registration to the Ddns server Email Notification 108 Email Notification window Email Address Setup 109 Email Address setup 126 Video Enhance Video Enhancement on Each Camera 114 Camera Input Video Enhancement on VGA Output 115 VGA Output 130 Remote Host Program 132 Remote Program Overview Remote system minimum requirements How to install the program Installing the Program to PCHow to set Screen Resolution and Color Quality How to setup the Internet Explorer Internet Explorer Click on the following message Remote Host Table. Description of Remote Host Program Button Setup Host Config window 140 Connection Capture Connect Dialog Status Mode Status 144 Playback control buttons Copy 147 Switch the Normal Screen to Full Screen 16 Full Screen Button Speaker / Microphone Buttons of Remote Host Program Connection mode Terminal mode Multi mode 20 Multi mode screen Copy in the Terminal mode 21 Copy Confirmation 153 Map Addition of map Placement of cameras on the map 27 Rename Usage of camera position Deletion of Camera position icon Pan / Tilt & Preset Channel Select PAN / Tilt Focus Zoom Preset / RUN Chart. Button of Player Program Player ② Calendar It shows the date currently being replayed 160 How to play the AVI files 38 Select one of the Channels 162 163 ⑩ Replay Control Refer to section Installation of additional HDDs HDD Hard Disk Drive Installation Installation of an additional HDD 168 Appendix Recording time table 480fps 240fps 160fps 120fps 48fps 32fps 16fps Factory default settings IR Remote ID OFF HDD Overwrite on 172 173 174 FAQ MY IP Can not loginPort 5800 on DVR Target Port Number 5800 on Host Program Limited 2Year Warranty How to obtain Factory Service