Rear | Clover Electronics CDR1650 instruction

5. Installation

-B

a.Display (Full / Split)

b.Emergency Record

c.Zoom

d.Quick Replay

e.OSD On/Off

f.Audio

g.Stop (ESC)

h.PTZ

zRear

VOLTAGE SELECT

LOOP OUT INPUTPOWER INLET

CAMERA INPUT

AUX VIDEO INPUT

MAIN VIDEO INPUT

RS-422C PORT

USB PORT

ETHERNET PORT

SENSOR IN/OUT

VGA

SPEAKER

AUDIO INPUT

[Fig 5-2 Rear View]

21

Image 21

Clover Electronics CDR1650 instruction manual Rear

Contents

Digital Video Recorder Page Contents System Disk Manager 133 158 Page About this manual Page Unpacking Stand-alone DVR Digital Video Recorder Unit Features Page Stand-alone DVR should be installed in the following order What to do at the time of InstallationPage Specifications Page Installation Controls and Connectors For 8Ch & 16Ch DVR Rear Page System Connection Camera Connection Connection of Normal Cameras InstallationConnection of Loop Output Monitor Connection Connection of Main Monitor VGA Monitor Connection Pin configuration of VGA Connector Sensor Connection and Relay in &OUT Sensor Connection Sensor Relay OUT Connection 4. RS232C, RS485, RS422 Connection Installation Power Connection How to operate Copying the Recorded Data During Replaying General Information Operating Interface 1IR Remote Controller IR Remote Controller Power on On the front panel or the remote controller Power On/OffPower OFF On the front panel or the remote controller By clicking the mouse 1 Power & Audio buttons Appearance or Disappearance of Power Button Live Screen Menu Bar On/Off Full Screen Display Screen Split Screen Split Screens Full Screen Sequencing Screen Quad Screen2page Sequencing Screen Screen Display pop-up screen Live Live Menu Display pop-up window Sequencing Screens Audio buttons Live Audio 10 Zoomed screen Zoom OSD on / OFF OSD on /OFF is possible in the Live mode or Record mode 13 PAN/TILT button PAN / Tilt Zoom / Focus Channel Selection and Screen ConversionButton of PAN/TILT Control window PAN / Tilt Preset Preset SetupPreset Execution 16 System Status button System Status Power Loss Lists Power Loss Lists 19 Power Loss Lists Message 20 Video Loss Lists window Video Loss List 22 Video Loss Lists Message window Record Manual Continuous recordingManual Event Recording 24 Manual Event Recording setup Timer Recording 26 Timer Event Recording setup Timer Event Recording 28 Recording Icons Recording Icons Replay Quick Replay Set the Start Time Playback Devices By using the Replay Time set-up bar By using the Replay Time set-up buttons How to Operate ③ REW/FF ② Play / Pause Disappearance of Replay control buttons ④ Prev / Next 36 Split screen during replaying Copying devices Copy Set the Copy Start Time Copying extent Regards to blank Medias CD-R/W and DVD-R/W 40 Copy Start time and Channel Selection window By using the Copy Start/End set-up buttons Set the Copy End Time Copying extent By using the Start/End set-up bar Copying the recorded data during replaying 43 Start Copy Time Setup window Network Copy Select Copy ModeUSB Copy CD-RW Copy 45 Copying Icon DVD-RW CopyPage Setup Audio Recording ON/OFF Microphone Volume Setup Setup Icon on Main Menu Setup System Time Format Time / Date Display Date Format 10 System Config Factory Default Load Config Load Config / Backup Config 14 Load Config window Backup Config Password Password ChangeON/OFF DVR IR ID Number IR Remote ID By USB memory Firmware UpdateBy DVR Master GUI System Info Disk Manager HDD Write Fail HDD OverwriteFormat 25 HDD Format window Camera Camera Name Camera Title Camera ON/OFF Relay Buzzer PTZ ID Pan/Tilt Settings 34 PAN/TILT & Remote 38 Baudrate button 42 Stop Bits button Sequencing dwell time Display Microphone Volume AudioAudio Recording ON/OFF Record Icon Display Record 54 All Manual / Timer button All Manual / Timer recording button 56 All Motion Setup button All Motion on / OFF, Sensitivity and Velocity Setting All Sensors on / OFF Size Recording Resolution 63 Record Speed button Recording Speed 65 Recording Speed for each channel Recording Quality Recording Mode Timer Recording Schedule RecordingManual Recording 105 106 By All Set 73 Spot Setup button 108 78 Window SET button By Window Set 110 82 Each Cell button By Each Cell 112 86 Sensor window Recording by Sensor PIR Sensor 114 115 Network GATEWAY, SUBNET, IP Address 93 IP Mode button Port 97 Port Setup window Disable / Enable MAC IDMNS MAC Name Server Site Name IP Address / Port 103 Ddns menu Ddns Dynamic Domain Name System Password Host NameUser ID Registration to the Ddns server HOW to Setup and USE the Ddns 7-7.7.1. Router 108 Email Notification window Email Notification 109 Email Address setup Email Address Setup 126 Video Enhance 114 Camera Input Video Enhancement on Each Camera 115 VGA Output Video Enhancement on VGA Output 130 Remote Host Program 132 Remote system minimum requirements Remote Program Overview Installing the Program to PC How to install the programHow to set Screen Resolution and Color Quality Internet Explorer How to setup the Internet Explorer Click on the following message Remote Host Table. Description of Remote Host Program Button Host Config window Setup 140 Connection Connect Dialog Capture Status Status Mode 144 Playback control buttons Copy 147 16 Full Screen Button Switch the Normal Screen to Full Screen Buttons of Remote Host Program Speaker / Microphone Terminal mode Connection mode 20 Multi mode screen Multi mode 21 Copy Confirmation Copy in the Terminal mode 153 Addition of map Map 27 Rename Placement of cameras on the map Deletion of Camera position icon Usage of camera position Channel Select PAN / Tilt Focus Zoom Preset / RUN Pan / Tilt & Preset Player Chart. Button of Player Program ② Calendar It shows the date currently being replayed 160 38 Select one of the Channels How to play the AVI files 162 163 ⑩ Replay Control Refer to section Installation of additional HDDs HDD Hard Disk Drive Installation Installation of an additional HDD 168 Appendix 480fps 240fps 160fps 120fps 48fps 32fps 16fps Recording time table IR Remote ID OFF HDD Overwrite on Factory default settings 172 173 174 FAQ Can not login MY IPPort 5800 on DVR Target Port Number 5800 on Host Program Limited 2Year Warranty How to obtain Factory Service