Epson TM-T85P manual GS L nL nH

Models: TM-T85 TM-T85P

1 115
Download 115 pages 23.45 Kb
Page 99
Image 99

 

 

 

 

Decimal

29

73

n

 

[Range]

 

 

1 ≤ n ≤ 3, 49 ≤ n ≤ 51

 

 

 

 

[Function]

Transmits the printer ID specified by n as follows:

 

 

 

 

 

 

 

 

 

 

n

 

 

Printer ID

 

Specification

ID (hexadecimal)

 

 

 

 

 

 

 

 

 

 

1, 49

 

 

 

Printer model ID

TM-T85/T85P

08H

 

 

 

 

 

 

 

 

 

 

2, 50

 

 

 

Type ID

 

See table below.

 

 

 

 

 

 

 

 

 

 

3, 51

 

 

 

ROM version ID

Depends on ROM version

 

 

 

 

 

 

 

 

 

n = 2, Type ID

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Bit

 

Off/On

Hex

Decimal

 

 

Function

 

 

 

 

 

 

 

 

 

 

0

 

Off

 

00

0

 

 

Two-byte character code not supported.

 

 

 

 

 

 

 

 

 

1

 

On

 

02

2

 

 

Auto-cutter equipped.

 

 

 

 

 

 

 

 

 

 

 

2

 

-

 

 

-

-

 

 

Undefined.

 

 

 

 

 

 

 

 

 

 

 

 

3

 

-

 

 

-

-

 

 

Undefined.

 

 

 

 

 

 

 

 

 

 

4

 

Off

 

00

0

 

 

Not used. Fixed to Off.

 

 

 

 

 

 

 

 

 

 

 

5

 

-

 

 

-

-

 

 

Undefined.

 

 

 

 

 

 

 

 

 

 

 

 

6

 

-

 

 

-

-

 

 

Undefined.

 

 

 

 

 

 

 

 

 

 

7

 

Off

 

00

0

 

 

Not used. Fixed to Off.

 

 

 

 

 

 

 

 

[Notes]

 

 

• When DTR/DSR control is selected, the printer transmits only 1

 

 

 

 

byte after confirming that the host is ready to receive data (DSR

 

 

 

 

signal is SPACE). If the host computer is not ready to receive data

 

 

 

 

(DSR signal is MARK), the printer waits until the host is ready.

When XON/XOFF control is selected, the printer transmits only 1 byte without confirming the condition of the DSR signal.

The printer ID is transmitted when the data in the receive buffer is developed. Therefore, there may be a time lag between receiving this command and transmitting the status, depending on the receive buffer status.

The ROM version may be changed.

When Auto Status Back (ASB) is enabled using GS a, the status transmitted by GS I and the ASB status must be differentiated.

GS L nL nH

[Name]

Set left margin

 

 

[Format]

ASCII

GS

L

nL nH

 

Hex

1D

4C

nL nH

 

Decimal

29

76

nL nH

Commands 5-41

Page 99
Image 99
Epson TM-T85P manual GS L nL nH