GAS Leak Test, GAS Pressure | Henny Penny OFG-390 guide

Model OFG- 390

2-7. GAS LEAK TEST

Prior to turning the gas supply on, be sure the gas valve knob on the gas control valve is in the OFF position. The word “OFF” is at the bottom of the knob when the valve is closed.

Upon initial installation and after moving the unit, the pipings and fittings should be checked for gas leaks.Asimple checking method is to turn on the gas and brush all connections with a soap solution. If bubbles and occur, it indicates escaping gas. In this event, the piping connection must be redone.

	To avoid fire or explosion, never use a lighted match
	or open flame to test for gas leaks. Ignited gas could
	result in severe personal injury and/or property
	damage.
2-8. GAS PRESSURE	The gas pressure regulator on the gas control valve is
REGULATOR SETTING	factory set as follows:
	Natural: 3.5 inches water column (.87 kPa)
	Propane: 10.0 inches water column (2.49 kPa)
	The gas pressure regulator has been set by Henny Penny and
	is not to be adjusted by the user.

MAKE SURE GAS PRESSURE IS SET COR-

RECTLY. FAILURE TO DO SO CAN RESULT IN

SHORTENINGOVERFLOWINGTHE FRYPOT,

WHICH COULD CAUSE SERIOUS BURNS,

PERSONAL INJURY, FIRE AND/OR PROPERTY

DAMAGE.

703

2-9

Image 19

Henny Penny OFG-390 manual GAS Leak Test, GAS Pressure, Regulator Setting

Contents

OPERATOR’S Manual Page Limited Warranty for Henny Penny Equipment Keep appliance area free and clear from combustibles Datos Tecnicos Para Products CE Henny Penny Head GAS Open Fryer Specifications Table of Contents Proper Care IntroductionAssistance Injury SafetyHazardous Situation WHICH, if not AVOIDED, will Result in Death or SeriousPage Unpacking Instructions Installation Strapped to the pallet, under the fryer Remove the counterweights from the pallet, which areUnpacking Instructions Optional Ramp Unloading Model OFG 908 Ment. Restraining ties may be used for stabilization Position and install fryer to prevent tipping or moveSelecting Location GAS Supply Ventilation of Fryer System at test pressures equal to or less than 1/2 During any pressure testing of the gas supply pipingFryer must be isolated from the gas supply piping System by closing its individual manual shutoff valve Model OFG 303 GAS Leak Test Regulator SettingGAS Pressure Requirements Electrical Model OFG Page Operation Operating Components Spark Ignitors Airflow SwitchHigh Limit Ignition Modules Melt Cycle SwitchesIndicators LID Operation ING is HOT and will Cause Burns Switches IndicatorsAlthough the Displaywillread Cool During the Standby MODE, the Shorten SMS Controls Filling or Adding Shortening Basic Operation Cool With Prolonged USE, the Flashpoint Care ShorteningWhich could Result in Serious Burns Personal INJURY, FIRE, AND/OR Property Filtering of Shortening Turn COOK/PUMP switch to OFF position Tube is not Tightened PROPERLY. if SO Cloth or Glove When TighteningSHORTENING, IT’S Possible That the Filter Connection AT the Union on the Filter Lightingand Shutdown of the Burners Cleaning the Frypot PROTECTOR-MANUAL ResetRegular Maintenance Filter Pump Motor Cleaning the Nylatrons Monthly Preventive MaintenanceLubricating Lid Rollers -Annually Maintenanc Preventive Code Programming After the proportional control, press and release Review Usage Special Program ModeReset Usage Programming Speaker Frequency, Codes, Initialize System Factory Presets F/C, Gas/Electric, Speaker Volume Appliance Test Tech I/O Mode Heat Control Special ProgramMode Problem Cause Correction Troubleshooting Trouble Shooting Guide Display Cause Panel Board Correction Error Codes 303 O S S a R Y Model OFG Shortening level also referred to as fill lines Gas fryers only See ignition modules Henny Penny Corp., Eaton, Ohio 45320, Revised