4–11

 

 

 

 

 

 

 

 

 

L100 Inverter

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Option

Terminal

Function Name

Input

 

 

Description

 

 

 

 

 

 

 

 

Code

Symbol

State

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Valid for inputs:

C_01, C_02, C_03, C_04,

Example (some CF inputs require input

 

C_05

 

 

 

 

 

configuration; some are default inputs—

 

Required settings:

F_01, A_01 = 02,

 

see page 3–32):

 

 

 

 

 

 

 

 

 

 

 

(MSB)

(LSB)

 

 

 

A_20 to A_35

 

 

 

 

 

 

 

 

 

CF4CF3CF2CF1

 

 

 

 

 

 

 

 

Notes:

 

 

 

 

• When programming the multi-speed settings, be

 

L

5

4

3

2

 

1

P24

 

 

sure to press the Store key each time and then set

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the next multi-speed setting. Note that when the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

key is not pressed, no data will be set.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•When a multi-speed setting more than 50Hz(60Hz)

is to be set, it is necessary to program the maximum

 

frequency A_04 high enough to allow that speed.

See I/O specs on page 4–6.

 

While using the multi-speed capability, you can monitor the current frequency with monitor function D_01 during each segment of a multi-speed operation.

There are two ways to program the speeds into the registers A_20 to A_35:

1.Standard keypad programming:

a.Select each parameter A_20 to A_35.

b.Press the FUNC. key to view the parameter value.

c.Use the 1 and 2 keys to edit the value.

d.Use the STR key to save the data to memory.

2.Programming using the CF switches. Set the speed by following these steps:

a.Turn the Run command OFF (Stop Mode).

b.Turn each switch ON and set it to Multi-speed. Display the value of F_01 on the digital operator.

c. Set the desired output frequency by pressing the 1 and 2 keys.

d.Press the STR key once to store the set frequency. When this occurs, F_01 indicates the output frequency of Multi-speed n.

e.Press the FUNC. key once to confirm that the indication is the same as the set frequency.

f.Repeat operations in 2. a) to 2. e) to set the frequency of other Multi-speeds. It can be set also by parameters A_20 to A_35 in the first procedure 1. a) to 1. d).

Operations Monitoring and