TV Operation, TV operation, TV channel receiving | Icom IC-R3

11 TV OPERATION

■TV operation

The receiver can receive TV (NTSC or PAL depending on ver- sion). TV channels are preset depending on versions.

The received video and audio can be output from [A/V OUT] if desired.

◊TV channel receiving

qPush [FUNC] + [↕] for 2 sec. to turn the color LCD ON, if desired.

• Only the audio part of the TV contents can be received.

wPush [↔] one or more times to select the TV channel band.

•“tV” and channel number appear in the sub LCD.

•The squelch is automatically opened. Push [SQL] to toggle be- tween squelch open and audio mute conditions.

eRotate [DIAL] to select the desired channel.

• Rotate [DIAL] while pushing [FUNC] to select the skip channel.

WFM

RX

◊Skip channel setting

Unwanted channels can be skipped for rapid selection, etc.

qRotate [DIAL] to select the channel to be skipped.

•To clear the skip setting, rotate [DIAL] while pushing [FUNC] to select a skip channel.

wWhile pushing [FUNC], push [(V/M) SKIP] for 2 sec. to tog-

gle the condition between non-skip and skip channel.

• No indication	: channel will not be skipped.
• “ ” appears	: channel skipped during selection.

To select a skip TV channel temporarily, rotate [DIAL] while pushing [FUNC].

◊Automatic TV channel programming

TV channels can be programmed automatically.

qPush [FUNC] + [↔] for 2 sec. to start TV channel pro- gramming.

wThe programming will automatically stop after scanning all channels.

34

Image 38

Icom IC-R3 TV Operation, TV operation, TV channel receiving, Skip channel setting, Automatic TV channel programming

Contents

IR3 Even when the receiver power is OFF, a slight current still You experience a ringing in your ears, reduce the volumeAreas with temperatures below -10C +14F or above +60C +140F Supplied Accessories Accessories included with the receiver Qty Table of Contents Antenna Accessory AttachmentBattery installation Belt clip Panel Description Panel description Monitor Switch SQL ATT VFO/MEMORY Switch V/M SkipMode Switch Mode SET External DC Power Jack DC Function display 2ATTENUATOR Indicator p Skip Scan Indicator pgsBattery Indicators Audio and video output jack information Dual LCD VFO and memory channels Frequency and Channel SettingWhat is VFO? Operating band selection Setting a frequency Setting a tuning step Attenuator function Push SQL ATT to exit the attenuator setting conditionSelecting a memory channel Lock function Receiving When a signal is receivedBasic Operation U.S.A. version automatically turns itself OFF when While pushing SQL, rotate Setting volume levelSetting squelch level Dial to select the squelch level Receive mode selection Monitor function Display backlighting Setting the backlighting conditionPush Func + Mode SET momentarily to enter set mode Rotate Dial until Light appears General Memory channel contentsMemory Channels Programming during selection Transferring memory contents to another memory Programming after selection Example Clearing memory channel 3 memory bank a Memory bank selection Memory clearPush Func + V/M for 2 sec. to clear Rotate the tuning dial to select the desired character Memory names Full Scan p Scan OperationScan types Function p Full/band/programmed scan Release ↔ to start the scan Memory bank scan To stop the scan, push ↔ again Selecting scan edges Band ranges Scan resume condition Skip channel settingSetting the scan pause time Rotate Dial until Pause Scan or Pause appears Setting the scan resume time Rotate Dial until Scan Resume or RESUmE appears Frequency skip function ON/OFF Frequency skip functionProgramming a skip frequency Memory Scan Watch p Priority WatchPriority watch types VFO Scan Watch p Memory channel watch and memory scan Watch Push Mode SET to exit set mode and start the watchPriority watch operation Rotate Dial to select Priority or PRIo VFO scan watch Tone squelch operation Setting subaudible tones for tone squelch OperationSubaudible Tone Operation Operation Available subaudible tone frequencies Unit Hz Pocket beep operationRotate Dial until Tone Freq. or tonE appears Push ↔ to stop the scan Tone scanPush SQL to stop the beeps and ﬂashing Rotate Dial until Duplex or dUP appears Duplex OperationDuplex shift direction Offset frequency Rotate Dial until Offset Freq. or oFFSEt appears Band Scope Range, if desired TV operation Skip channel settingTV Operation TV channel receiving Push ↔ one or more times to select the band above 30 MHz TV frequency AM TV receivingTV frequency AM TV memory channel Push Func + one or more times to select the TV screen ATV memory channel Sub carrier adjustmentATV operation Direction Finding Signal sourceSignal levels Direction ﬁnding function example Other Functions Set modeSet mode items Release Func to exit the condition Setting dial select stepDial select step Beep tones Auto power-off functionRotate Dial until A.Power OFF or AP oFF appears Rotate Dial until Beep Audio or bEEP appears Rotate Dial until Power Save or P Save appears Power saverMonitor switch action Rotate Dial until Monitor or monI appears Rotate Dial until Dial Speedup or SPEEd appears Dial speed accelerationLock function effect Rotate Dial until Key Lock or LoCk appears Display contrast Display mode selectionColor LCD can be automatically turned on when using Rotate Dial until Display or dISP appears Rotate Dial until Bright appears Display brightnessDisplay background color Push Power for 2 sec. to turn power OFF Partial resetTotal reset Cloning function Battery charging Battery ChargingBattery cautions Battery pack installation Regular charging CP-18A/E fuse ReplacementCP-18A/ETurn power OFF Check Rapid charging with the BC-135 Operation Flow Chart Memory mode VFO mode Scan resume time p Confirmation beep p Backlighting p Power save pAuto power OFF p Ccir channels TV Frequency TableA. channels New Zealand channels Australian channelsTaiwan channels China channels Indonesian channels Italian channels FOT channels Receiver Specifications and OptionsGeneral Operating periods Approx Options Troubleshooting Problem Possible Cause Solution Quick Reference Quick Reference Declaration of Conformity Kamihigashi, Hirano-ku, Osaka 547-0002 Japan