Ingersoll-Rand HP50-PE manual Installation / Handling, 60Hz, UP6 50PE UP6 50PEI, HF50-PE, EP50-PE

INSTALLATION / HANDLING 15

60Hz

UP6 40

UP6 50PE

UP6 50PEI

HF50–PE EP50–PE HP50–PE HXP50–PE

COMPRESSOR	115		125	150		200		115		125	150	200
Maximum operating pressure	115		125	150		200		115		125	150	200
psig (barg)	(8.0)		(8.5)	(10.3)		(13.8)		(8.0)		(8.5)	(10.3)	(13.8)
Factory set reload pressure	105		115	140		190		105		115	140	190
psig (barg)	(7.2)		(7.9)	(9.6)		(13.1)		(7.2)		(7.9)	(9.6)	(13.1)
Flow rate	188		185	170		143		212		208	201	167
cfm (m3/min)	(5.32)		(5.24)	(4.81)		(4.05)		(6.02)		(5.89)	(5.70)	(4.73)
Maximum airend discharge						216 F (102 C)
temperature
Ambient operating		36 F(+2 C ) ?		105 F(+40 C)				36 F(+2 C ) ?			115 F(+46 C)
temperature
min. max.
MOTOR
Motor enclosure		ODP		TEFC				ODP			TEFC
Nominal power			40HP							50HP
Speed			1775 RPM							1775 RPM
Frame		324T		324T				326T			326T
Insulation class							F
COOLING SYSTEM – Air cooled
Cooling air flow			3100 ft3/min (87.8m3/min)						3900 ft3/min (110m3/min)
Dryer cooling air flow					1200 ft3/min			(34m3/min)
Maximum ∆P in air ducts			0.5 inWg (12.7mmH2O) (not recommended for dryer openings)
Compressed air outlet ∆T			15 F (8.3 C)							15 F (8.3 C)
Cooling air outlet ∆T			40 F (22 C)							42 F (23 C)
Dryer cooling air outlet ∆T						11 F (6 C)
GENERAL DATA
Residual coolant content						3ppm (3 mg/m3)
Separator vessel capacity					3.7 US gallons (14 liters)
Coolant capacity					5.5 US gallons (21 liters)
Sound pressure level to			69 dB(A)							69 dB(A)
CAGI–PNEUROP
(Non–dryer unit)
Weight – base mount unit		2326 lbs		2436 lbs				2384 lbs			2476 lbs
	(1055 kg)			(1105 kg)				(1081 kg)			(1123 kg)
Weight – dryer option unit		2576 lbs		2686 lbs				2634 lbs			2726 lbs
	(1168 kg)			(1218 kg)				(1194 kg)			(1236 kg)

CAUTION

230/460 Dual voltage machines are fitted with a decal to advise the correct supply voltage as connected from the factory.

Factory units wired for 230V supply can be re–wired to 460V supply voltage by re–wiring the main drive motor and the fan motor as shown on the electrical schematic AND by replacing the fan motor starter CCN 22395800 - 50HP with CCN 22395792

-50 HP (shipped loose). The main motor overload and the fan motor starter overload settings should be adjusted accordingly – reference the IEC decal mounted inside the starter door. Also, the transformer primary voltage connections will need to be re–wired for the new supply voltage.

Re–wiring should only be effected by a competent Electrician.

http://air.ingersollrand.com SSR UP6 40, SSR UP6 50PE, SSR UP6 50PEI, HF50–PE, EP50–PE,

HP50–PE, HXP50–PE