Intel 830 8

Datasheet 97

Balanced Technology Extended (BTX) Type I Boxed Processor Specifications

8Balanced Technology Extended

(BTX) Type I Boxed Processor

Specifications

The Intel® Pentium® D processor will also be offered as an boxed Intel processor. Boxed Intel

processors are intended for system integrators who build systems from largely standard

components. The boxed Intel Pentium D processor will be supplied with a cooling solution known

as the Thermal Module Assembly (TMA). Figure 8-1 shows a mechanical representation of a

boxed Pentium D processor. This chapter documents mainboard and system requirements for the

TMA that will be supplied with the boxed Pentium D processor. This chapter is particularly

important for OEMs that manufacture mainboards for system integrators.

Note: Unless otherwise noted, all figures in this chapter are dimensioned in millimeters and inches

[in brackets].

Note: Drawings in this section reflect only the specifications on the boxed Intel processor product. These

dimensions should not be used as a generic keep-out zone for all cooling solutions. It is the system

designer’s responsibility to consider their proprietary cooling solution when designing to the

required keep-out zone on their system platforms and chassis. Refer to the Intel® Pentium® D

Processor and Intel® Pentium® Processor Extreme Edition 840 Thermal and Mechanical Design

Guidelines for further guidance.

NOTE: The duct, clip, heatsink, and fan can differ from this drawing representation; however, the basic shape

and size will remain the same.

Figure 8-1. Mechanical Representation of the Boxed Processor

Contents

Main Contents Contents Page Figures Tables Revision History Page Intel Pentium D Processor 800 Sequence Features Page 1 1.1 Terminology 1.1.1 Processor Packaging Terminology Introduction 1.2 References Table 1-1. References Page 2 2.1 Power and Ground Lands 2.2 Decoupling Guidelines 2.2.1 VCC Decoupling 2.2.2 VTT Decoupling 2.3 Voltage Identification Table 2-1. Voltage Identification Definition 2.4 Reserved, Unused, FC and TESTHI Signals 2.5 Voltage and Current Specifications 2.5.1 Absolute Maximum and Minimum Ratings 2.5.2 DC Voltage and Current Specifications Table 2-3. Voltage and Current Specifications Table 2-4. VCC Static and Transient Tolerance for 775_VR_CONFIG_05A Pentium D Processor Figure 2-1. VCC Static and Transient Tolerance for 775_VR_CONFIG_05A Pentium D Processor Table 2-5. VCC Static and Transient Tolerance for 775_VR_CONFIG_05B Pentium D Processor Figure 2-2. VCC Static and Transient Tolerance for 775_VR_CONFIG_05B Pentium D Processor 2.5.3 VCC Overshoot Specification Time Example Overshoot Waveform T VID 2.6 Signaling Specifications 2.6.1 FSB Signal Groups Table 2-7. FSB Signal Groups 2.6.2 GTL+ Asynchronous Signals Table 2-8. Signal Characteristics Table 2-9. Signal Reference Voltages 2.6.3 FSB DC Specifications Table 2-11. GTL+ Signal Group DC Specifications Table 2-12. PWRGOOD Input and TAP Signal Group DC Specifications Table 2-13. GTL+ Asynchronous Signal Group DC Specifications 2.6.3.1 GTL+ Front Side Bus Specifications Table 2-14. VTTPWRGD DC Specifications Table 2-15. BOOTSELECT and MSID[1:0] DC Specifications Table 2-16. GTL+ Bus Voltage Definitions 2.7 Clock Specifications 2.7.1 FSB Clock (BCLK[1:0]) and Processor Clocking 2.7.2 FSB Frequency Select Signals 2.7.3 Phase Lock Loop (PLL) and Filter Figure 2-4. Phase Lock Loop (PLL) Filter Requirements 3 Specifications 3.1 Package Mechanical Drawing Page Page Page 3.2 Processor Component Keep-Out Zones 3.3 Package Loading Specifications 3.4 Package Handling Guidelines 3.5 Package Insertion Specifications 3.6 Processor Mass Specification 3.7 Processor Materials 3.8 Processor Markings Page Package Mechanical Specifications 3.9 Processor Land Coordinates Figure 3-7. Processor Land Coordinates, Top View Socket LGA775 Quadrants Top View V CC / V VTT / Clocks Data 4 Figure 4-1. Landout Diagram (Top View Left Side) Figure 4-2. Landout Diagram (Top View Right Side) Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 4.2 Alphabetical Signals Reference Table 4-3. Signal Description (Sheet 1 of 8) Table 4-3. Signal Description (Sheet 2 of 8) Table 4-3. Signal Description (Sheet 3 of 8) Table 4-3. Signal Description (Sheet 4 of 8) Table 4-3. Signal Description (Sheet 5 of 8) Table 4-3. Signal Description (Sheet 6 of 8) Table 4-3. Signal Description (Sheet 7 of 8) Table 4-3. Signal Description (Sheet 8 of 8) Page 5 Design Considerations 5.1 Processor Thermal Specifications 5.1.1 Thermal Specifications Page Figure 5-1. Thermal Profile for the Pentium D Processor with PRB=1 Figure 5-2. Thermal Profile for the Pentium D Processor with PRB=0 5.1.2 Thermal Metrology 5.2 Processor Thermal Features 5.2.1 Thermal Monitor 5.2.2 On-Demand Mode 5.2.3 PROCHOT# Signal 5.2.4 FORCEPR# Signal Pin 5.2.5 THERMTRIP# Signal 5.2.6 TCONTROL and Fan Speed Reduction 5.2.7 Thermal Diode Page Page 6 6.1 Power-On Configuration Options 6.2 Clock Control and Low Power States 6.2.1 Normal State 6.2.2 HALT and Enhanced HALT Powerdown States 6.2.2.1 HALT Powerdown State 6.2.2.2 Enhanced HALT Powerdown State 6.2.3 Stop-Grant State 6.2.4 Enhanced HALT Snoop or HALT Snoop State, Grant Snoop State 6.2.4.1 HALT Snoop State, Grant Snoop State 6.2.4.2 Enhanced HALT Snoop State 6.2.5 Enhanced Intel SpeedStep Techn olo gy 7 7.1 Mechanical Specifications 7.1.1 Boxed Processor Cooling Solution Dimensions 7.1.2 Boxed Processor Fan Heatsink Weight 7.1.3 Boxed Processor Retention Mechanism and Heatsink Attach Clip Assembly 7.2 Electrical Requirements 7.2.1 Fan Heatsink Power Supply Page 7.3 Thermal Specifications 7.3.1 Boxed Processor Cooling Requirements Page 7.3.2 Variable Speed Fan Page 8 (BTX) Type I Boxed Processor Specifications 8.1 Mechanical Specifications 8.1.1 Cooling Solution Dimensions 8.1.2 Boxed Processor Fan Heatsink Weight 8.1.3 Boxed Processor Support and Retention Module (SRM) 8.2 Electrical Requirements 8.2.1 Fan Heatsink Power Supply Page 8.3 Thermal Specifications 8.3.1 Boxed Processor Cooling Requirements 8.3.2 Variable Speed Fan Page Page 9 9.1 Logic Analyzer Interface (LAI) 9.1.1 Mechanical Considerations 9.1.2 Electrical Considerations