Standard configuration of Network Settings | JAI TS-1327EN manual

VIS-CAM System

Network Settings:
IP address:	Enter the desired IP address of the unit. The default address from the
	factory is 192.168.127.254 unless otherwise specified.
Netmask:	Enter the subnet mask of the unit. The default subnet mask from the
	factory is 255.255.255.0 unless otherwise specified.
Gateway:	Enter the default gateway of the unit.
IP Configuration:	Specify whether the unit uses static of dynamic IP address.
DNS Server 1	Specify primary DNS server to be used by the unit.
DNS Server 2	Specify secondary DNS server to be used by the unit.
SNMP.	Enables / Disables the SNMP protocol.
Auto report to IP:	Reports generated by the auto report function will be automatically be
	forwarded to IP address specified in this field.

Auto report to TCP Port: Specify the TCP port number for the auto report function. The default

	port is 4002.
Auto report period:	Time interval for error reporting.

Figure 88. Standard configuration of Network Settings:


88		Appendix E: Moxa N Port 5232 Configuration

Image 100

JAI TS-1327EN, TS-9720EN, TS-2030EN manual Standard configuration of Network Settings

Contents

VIS-CAM System Page Warranty CertificationsVIS-CAM System Disclaimer Mailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of Figures Standard configuration of Serial settings for port List of Tables List of Tables VIS-CAM System Xii List of Tables Introduction Document OverviewProduct overview Introduction System Components description Preparing for InstallationTraffic Light Sensor TLS300 Back shot VIS installation Viscam Operational Overview Installation Preparation Preparing for installationOver Lane Positioning Asynchronous triggering considerations Camera tilt considerationsCamera height versus trigger distance considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Side of Road Installation Typical side of road installation Flash and camera distances VIS-CAM System Preparing for Installation Installing the Vehicle Imaging System Installing the TNF-300 Traffic Light SensorInstalling the Vehicle Imaging Subsystem To install the Traffic Light Sensor Mounting pipe and flange Wire color SignalLight Sensor Cables Installing the Cameras Optional Side Mount Camera mount template Electrical wiring for the VIS CAM installation X4 Pin # Wire Color Signal Remarks Properly wired X-4 connector VIS-CAM System Installing the J-Panel X1, X2 Pin # Wire Color Signal Remarks1 X1 and X2 VIS CAM 300/400 VIS CAM connections to the J-Panel TLS 300 to J-Panel connections X7 Pin Power input to the J-Panel X6 Pin # Signal Description Connection to 6 Power input connection 4 X8 LS RS485 Out Connector X8 to converter connector 5 X14 Trigger Input Connector Trigger input connectorX14 Pin # Signal Description Connection to Trigger polarity X15 Pin # Signal Description Connection to X15 Lane ControllerArrow down negative going Test Trigger Pin Signal Description Connection to Installing the TNF-31 FlashIllumination Options Trigger Options Installing The Laser Vehicle DetectorOptimal Illumination Distance Between Camera and TNF Connection for LVD to VIS CAM Wiring for LVD to VIS CAM X7 Pin # Signal Description Connection to VIS-CAM System Installing the Vehicle Imaging Subsystem Pre-Alignment Checklist System Set-UpPreparation for Alignment System Set-Up Validate the Installation Geometry Edit the alignment settings on the Setup ComputerTypical minimum plate heights and nominal plate heights Select the Camera to Align Connect the Setup Computer to the Camera Example of a network connection using a local switch Perform Initial Lens Adjustment and Camera Aiming Drive and Park the Setup Vehicle CorrectlyProperly Position the License Plate Stand Initial Camera Alignment Display example Roll Bar Display example Finalize Lens Adjustments and Camera Aiming Perform Final Camera Mount and Lens Adjustments Focus Bar marker display Focus Bar Waveform display Focus Bar Waveform Display with waveform cursors Flash Head Alignment Optimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional and Connector Description Appendix a Camera Functional & Connector Description VIS-CAM System I/O Board Layout Component layout of the EN board Connector specification Connector signal specificationsSignal levels VIS-CAM System X4 I/O Board Connection to J-panel Electrical interface on the I/O board Trigger input Description Connector physical Interface . Physical interface table Power inputConnection to Pin Signal Description Panel Remarks Ethernet Interface Typical wiring diagram I/O Board Flash Connection External power requirement Output signal specificationDescription Connection DC Flash to an internally powered board VIS-CAM System IO board electrical interface Test Connector physical Interface Physical interface pinouts Connecting the second AC flash VIS-CAM System Night Light TNC 100 Connection X7I/O Board Laser Vehicle Detector Connection Trigger Input Power OutputCommunication X1, X3 I/O Board Ethernet Test Connectors Connector physical Interface Connector table Test setup Pin Signal Description Connection to Remarks VIS-CAM System VIS-CAM System X15 I/O Board Auxiliary power connector Cable SpecificationsRS485 and power Cables Recommended Cables Combined cable Ethernet, RS485 and powerMounting the cables Page Appendix B J-Panel Functional and Connector Description Appendix B J-Panel Functional & Connector DescriptionPanel Layout X1 J-panel connection to Camera Trigger output Description Signal parameters and conditionsElectrical interface on the J-Panel Connector physical Interface Physical interface table Pin Signal Description Connection to Remarks Board Indicators LED indicatorsSwitches Switch labels VIS-CAM System X2 J-panel connection to Camera Board and camera J-panel connection to camera Functionality Signal table Connector physical Interface Ethernet physical connections Category 5 or 6 ethernet wiring diagram Connector switches X3 Light Sensor Connection X4 Lane Controller Signal to J-Panel #2 Connector physical Interface Physical interface connectionsLED physical indicators Databus D0 and D1 X5 Lane Controller Signal from J-Panel #1 Datasignal Data signal X6, X7 24V DC PowerPhysical pin connections J-panel #1 Principle in the power distribution Connector specification Connector physical Interface RS485 physical connections X11 Ethernet Interface from Camera Connector physical Interface Physical connector description 10 X12 Ethernet Interface from Camera 11 X14 External Trigger External Trigger connection Functionality Trigger 0 Electrical interface on the J-Panel Trigger 1 Electrical interface on the J-Panel Common Lane Controller 12 X15 Lane Controller interface 6.12.1 FunctionalityTwo Lane Controllers Connector physical Interface Wago physical interface Connecting Lane Controller RS485 signal between J-Panels Appendix C Two Cameras, One Flash Configuration Appendix C Two Cameras, One-Flash Configuration Master Flash Connector Slave Laser Connector Master to slave connections Appendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal Blocks VIS-CAM System Appendix D Pluggable Terminal Blocks Appendix E Moxa N Port 5232 Configuration Appendix E Moxa N-Port 5232 ConfigurationBasic Settings Standard configuration of Network Settings Network Settings Standard configuration of Serial settings for port Serial port 1 settings Configuration overview of serial port 1 TCP Server Mode Operating settings portData Packing VIS-CAM System Appendix F Multiple Moxa N-port Configuration Diagram Appendix F Multiple Moxa N port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Appendix H Troubleshooting Appendix H TroubleshootingFault Symptom Check/Possible Reason VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa