Category 5 or 6 ethernet wiring diagram | JAI TS-2030EN, TS-9720EN

VIS-CAM System

6.3.4Connector physical Interface

		Table 22	Ethernet physical connections

	Pin	Signal	Description	Connection to	Remarks
	Pin	Signal	Description	I/O Board X4	Remarks
				I/O Board X4

	1	Ethernet A+	Ethernet signal to gigabit switch	pin 1	Cat5e/6 cable white/orange

	2	Ethernet A-	Ethernet signal to gigabit switch	Pin 2	Cat5e/6 cable orange

	3	Ethernet B+	Ethernet signal to gigabit switch	Pin 3	Cat5e/6 cable white/green

	4	Ethernet B-	Ethernet signal to gigabit switch	Pin 4	Cat5e/6 cable green

	5	Ethernet C+	Ethernet signal to gigabit switch	Pin 5	Cat5e/6 cable white/blue

	6	Ethernet C-	Ethernet signal to gigabit switch	Pin 6	Cat5e/6 cable blue

	7	Ethernet D+	Ethernet signal to gigabit switch	Pin 7	Cat5e/6 cable white/brown

	8	Ethernet D-	Ethernet signal to gigabit switch	Pin 8	Cat5e/6 cable brown

	9	Gnd	Power ground	Pin 9	Black wire in Red/Black pair

	10	+24V dc	Supply voltage	Pin 10	Red wire in Red/Black pair

	11	Vinit +	Balanced trigger pulse positive	Pin 11	White wire in Brown/White pair

	12	Vinit -	Balance tripper pulse negative	Pin 12	Brown wire in Brown/White pair

	13	RS485D+	RS485 Data+ for Lane Controller	Pin 13	White wire in Red/White pair

	14	RS485D-	RS485 Data- for Lane Controller	Pin 14	Red wire in Red/White pair

	15	RS485D=	RS485 Data+ for Lane Controller	Pin 15	White wire in Orange/White pair

	16	RS485D-	RS485 Data- for Lane Controller	Pin 16	Orange wire in Orange/White pair

6.3.5Typical Wiring diagram

Figure 69. Category 5 or 6 ethernet wiring diagram.

Appendix B: J-Panel Functional & Connector Description

71

Image 83

JAI TS-2030EN manual Connector physical Interface Ethernet physical connections, Category 5 or 6 ethernet wiring diagram

Contents

VIS-CAM System Page Disclaimer WarrantyCertifications VIS-CAM System Mailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of Figures Standard configuration of Serial settings for port List of Tables List of Tables VIS-CAM System Xii List of Tables Introduction IntroductionDocument Overview Product overview Traffic Light Sensor TLS300 Preparing for InstallationSystem Components description Viscam Back shot VIS installation Operational Overview Over Lane Positioning Preparing for installationInstallation Preparation Camera height versus trigger distance considerations Camera tilt considerationsAsynchronous triggering considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Typical side of road installation Side of Road Installation Flash and camera distances VIS-CAM System Preparing for Installation To install the Traffic Light Sensor Installing the Vehicle Imaging SystemInstalling the TNF-300 Traffic Light Sensor Installing the Vehicle Imaging Subsystem Light Sensor Cables Wire color SignalMounting pipe and flange Optional Side Mount Installing the Cameras Camera mount template X4 Pin # Wire Color Signal Remarks Electrical wiring for the VIS CAM installation Properly wired X-4 connector VIS CAM connections to the J-Panel VIS-CAM System Installing the J-PanelX1, X2 Pin # Wire Color Signal Remarks 1 X1 and X2 VIS CAM 300/400 X7 Pin TLS 300 to J-Panel connections X6 Pin # Signal Description Connection to Power input to the J-Panel X8 to converter connector 6 Power input connection 4 X8 LS RS485 Out Connector Trigger polarity 5 X14 Trigger Input ConnectorTrigger input connector X14 Pin # Signal Description Connection to Test Trigger X15 Pin # Signal Description Connection toX15 Lane Controller Arrow down negative going Illumination Options Installing the TNF-31 FlashPin Signal Description Connection to Optimal Illumination Distance Between Camera and TNF Installing The Laser Vehicle DetectorTrigger Options X7 Pin # Signal Description Connection to Connection for LVD to VIS CAM Wiring for LVD to VIS CAM VIS-CAM System Installing the Vehicle Imaging Subsystem System Set-Up Pre-Alignment ChecklistSystem Set-Up Preparation for Alignment Select the Camera to Align Validate the Installation GeometryEdit the alignment settings on the Setup Computer Typical minimum plate heights and nominal plate heights Example of a network connection using a local switch Connect the Setup Computer to the Camera Properly Position the License Plate Stand Drive and Park the Setup Vehicle CorrectlyPerform Initial Lens Adjustment and Camera Aiming Initial Camera Alignment Display example Roll Bar Display example Perform Final Camera Mount and Lens Adjustments Finalize Lens Adjustments and Camera Aiming Focus Bar marker display Focus Bar Waveform display Flash Head Alignment Focus Bar Waveform Display with waveform cursors Optimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional & Connector Description Appendix a Camera Functional and Connector Description Component layout of the EN board VIS-CAM System I/O Board Layout VIS-CAM System X4 I/O Board Connection to J-panel Connector specificationConnector signal specifications Signal levels Trigger input Description Electrical interface on the I/O board Ethernet Interface Connector physical Interface . Physical interface tablePower input Connection to Pin Signal Description Panel Remarks I/O Board Flash Connection Typical wiring diagram Description Output signal specificationExternal power requirement Connection DC Flash to an internally powered board VIS-CAM System Test IO board electrical interface Physical interface pinouts Connector physical Interface Connecting the second AC flash X7I/O Board Laser Vehicle Detector Connection VIS-CAM System Night Light TNC 100 Connection Communication Power OutputTrigger Input Connector physical Interface Connector table X1, X3 I/O Board Ethernet Test Connectors Pin Signal Description Connection to Remarks Test setup VIS-CAM System Cables VIS-CAM System X15 I/O Board Auxiliary power connectorCable Specifications RS485 and power Mounting the cables Combined cable Ethernet, RS485 and powerRecommended Cables Page X1 J-panel connection to Camera Appendix B J-Panel Functional and Connector DescriptionAppendix B J-Panel Functional & Connector Description Panel Layout Electrical interface on the J-Panel Signal parameters and conditionsTrigger output Description Pin Signal Description Connection to Remarks Board Connector physical Interface Physical interface table Switch labels IndicatorsLED indicators Switches Board and camera J-panel connection to camera Functionality VIS-CAM System X2 J-panel connection to Camera Signal table Category 5 or 6 ethernet wiring diagram Connector physical Interface Ethernet physical connections X3 Light Sensor Connection Connector switches Databus D0 and D1 X4 Lane Controller Signal to J-Panel #2Connector physical Interface Physical interface connections LED physical indicators Datasignal X5 Lane Controller Signal from J-Panel #1 Physical pin connections J-panel #1 X6, X7 24V DC PowerData signal Principle in the power distribution Connector specification X11 Ethernet Interface from Camera Connector physical Interface RS485 physical connections 10 X12 Ethernet Interface from Camera Connector physical Interface Physical connector description External Trigger connection Functionality 11 X14 External Trigger Trigger 1 Electrical interface on the J-Panel Trigger 0 Electrical interface on the J-Panel Two Lane Controllers 12 X15 Lane Controller interface 6.12.1 FunctionalityCommon Lane Controller Connecting Lane Controller RS485 signal between J-Panels Connector physical Interface Wago physical interface Appendix C Two Cameras, One-Flash Configuration Appendix C Two Cameras, One Flash Configuration Master to slave connections Master Flash Connector Slave Laser Connector Appendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal Blocks VIS-CAM System Appendix D Pluggable Terminal Blocks Basic Settings Appendix E Moxa N-Port 5232 ConfigurationAppendix E Moxa N Port 5232 Configuration Network Settings Standard configuration of Network Settings Serial port 1 settings Standard configuration of Serial settings for port Configuration overview of serial port 1 Data Packing Operating settings portTCP Server Mode VIS-CAM System Appendix F Multiple Moxa N port Configuration Diagram Appendix F Multiple Moxa N-port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Fault Symptom Check/Possible Reason Appendix H TroubleshootingAppendix H Troubleshooting VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa