Power Output, Trigger Input, Communication | JAI TS-1327EN manual

VIS-CAM System

5.5.1Functionality

Connection to the Laser Vehicle Detector (LVD).

5.5.2Connector specification

Connector type:	8 pole WAGO pluggable terminal block
Connector on board:	WAGO 734-238
Cable part:	WAGO 734-208

5.5.3Connector signal specifications

5.5.3 (a) Power Output

Voltage	24V DC
Fuse	0.5A (PTC fuse, self resetable)
5.5.3 (b) Trigger Input

The LVD trigger input is shown in Figure 57. The input specification is

Input impedance	10k pull-up
Signal level	3.3V logic

Figure 57. LVD Trigger Input

5.5.3 (c) Communication

The communication with the Laser Vehicle Detector is RS485 signal levels.

Figure 58. Electrical interface on the I/O board:


58		Appendix A: Camera Functional & Connector Description

Image 70

JAI TS-1327EN, TS-9720EN, TS-2030EN manual Power Output, Trigger Input, Communication

Contents

VIS-CAM System Page VIS-CAM System WarrantyCertifications Disclaimer Mailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of Figures Standard configuration of Serial settings for port List of Tables List of Tables VIS-CAM System Xii List of Tables Product overview IntroductionDocument Overview Introduction System Components description Preparing for InstallationTraffic Light Sensor TLS300 Back shot VIS installation Viscam Operational Overview Installation Preparation Preparing for installationOver Lane Positioning Asynchronous triggering considerations Camera tilt considerationsCamera height versus trigger distance considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Side of Road Installation Typical side of road installation Flash and camera distances VIS-CAM System Preparing for Installation Installing the Vehicle Imaging Subsystem Installing the Vehicle Imaging SystemInstalling the TNF-300 Traffic Light Sensor To install the Traffic Light Sensor Mounting pipe and flange Wire color SignalLight Sensor Cables Installing the Cameras Optional Side Mount Camera mount template Electrical wiring for the VIS CAM installation X4 Pin # Wire Color Signal Remarks Properly wired X-4 connector 1 X1 and X2 VIS CAM 300/400 VIS-CAM System Installing the J-PanelX1, X2 Pin # Wire Color Signal Remarks VIS CAM connections to the J-Panel TLS 300 to J-Panel connections X7 Pin Power input to the J-Panel X6 Pin # Signal Description Connection to 6 Power input connection 4 X8 LS RS485 Out Connector X8 to converter connector X14 Pin # Signal Description Connection to 5 X14 Trigger Input ConnectorTrigger input connector Trigger polarity Arrow down negative going X15 Pin # Signal Description Connection toX15 Lane Controller Test Trigger Pin Signal Description Connection to Installing the TNF-31 FlashIllumination Options Trigger Options Installing The Laser Vehicle DetectorOptimal Illumination Distance Between Camera and TNF Connection for LVD to VIS CAM Wiring for LVD to VIS CAM X7 Pin # Signal Description Connection to VIS-CAM System Installing the Vehicle Imaging Subsystem Preparation for Alignment Pre-Alignment ChecklistSystem Set-Up System Set-Up Typical minimum plate heights and nominal plate heights Validate the Installation GeometryEdit the alignment settings on the Setup Computer Select the Camera to Align Connect the Setup Computer to the Camera Example of a network connection using a local switch Perform Initial Lens Adjustment and Camera Aiming Drive and Park the Setup Vehicle CorrectlyProperly Position the License Plate Stand Initial Camera Alignment Display example Roll Bar Display example Finalize Lens Adjustments and Camera Aiming Perform Final Camera Mount and Lens Adjustments Focus Bar marker display Focus Bar Waveform display Focus Bar Waveform Display with waveform cursors Flash Head Alignment Optimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional and Connector Description Appendix a Camera Functional & Connector Description VIS-CAM System I/O Board Layout Component layout of the EN board Signal levels Connector specificationConnector signal specifications VIS-CAM System X4 I/O Board Connection to J-panel Electrical interface on the I/O board Trigger input Description Connection to Pin Signal Description Panel Remarks Connector physical Interface . Physical interface tablePower input Ethernet Interface Typical wiring diagram I/O Board Flash Connection External power requirement Output signal specificationDescription Connection DC Flash to an internally powered board VIS-CAM System IO board electrical interface Test Connector physical Interface Physical interface pinouts Connecting the second AC flash VIS-CAM System Night Light TNC 100 Connection X7I/O Board Laser Vehicle Detector Connection Trigger Input Power OutputCommunication X1, X3 I/O Board Ethernet Test Connectors Connector physical Interface Connector table Test setup Pin Signal Description Connection to Remarks VIS-CAM System RS485 and power VIS-CAM System X15 I/O Board Auxiliary power connectorCable Specifications Cables Recommended Cables Combined cable Ethernet, RS485 and powerMounting the cables Page Panel Layout Appendix B J-Panel Functional and Connector DescriptionAppendix B J-Panel Functional & Connector Description X1 J-panel connection to Camera Trigger output Description Signal parameters and conditionsElectrical interface on the J-Panel Connector physical Interface Physical interface table Pin Signal Description Connection to Remarks Board Switches IndicatorsLED indicators Switch labels VIS-CAM System X2 J-panel connection to Camera Board and camera J-panel connection to camera Functionality Signal table Connector physical Interface Ethernet physical connections Category 5 or 6 ethernet wiring diagram Connector switches X3 Light Sensor Connection LED physical indicators X4 Lane Controller Signal to J-Panel #2Connector physical Interface Physical interface connections Databus D0 and D1 X5 Lane Controller Signal from J-Panel #1 Datasignal Data signal X6, X7 24V DC PowerPhysical pin connections J-panel #1 Principle in the power distribution Connector specification Connector physical Interface RS485 physical connections X11 Ethernet Interface from Camera Connector physical Interface Physical connector description 10 X12 Ethernet Interface from Camera 11 X14 External Trigger External Trigger connection Functionality Trigger 0 Electrical interface on the J-Panel Trigger 1 Electrical interface on the J-Panel Common Lane Controller 12 X15 Lane Controller interface 6.12.1 FunctionalityTwo Lane Controllers Connector physical Interface Wago physical interface Connecting Lane Controller RS485 signal between J-Panels Appendix C Two Cameras, One Flash Configuration Appendix C Two Cameras, One-Flash Configuration Master Flash Connector Slave Laser Connector Master to slave connections Appendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal Blocks VIS-CAM System Appendix D Pluggable Terminal Blocks Appendix E Moxa N Port 5232 Configuration Appendix E Moxa N-Port 5232 ConfigurationBasic Settings Standard configuration of Network Settings Network Settings Standard configuration of Serial settings for port Serial port 1 settings Configuration overview of serial port 1 TCP Server Mode Operating settings portData Packing VIS-CAM System Appendix F Multiple Moxa N-port Configuration Diagram Appendix F Multiple Moxa N port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Appendix H Troubleshooting Appendix H TroubleshootingFault Symptom Check/Possible Reason VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa