Side of Road Installation | JAI TS-2030EN, TS-9720EN, TS-1327EN

VIS-CAM System

2.1.2Side of Road Installation

Figure 7. Typical side of road installation.

Figure 8. Typical side of road installation plan view with no canopy/overhead structue.

Generally the flash head must be separated from the camera by a radial distance of at least three and a half feet (1.2 meters).

If the flash is positioned closer to the camera, reflections from the license plate will cause overexposure.

If possible, position the flash head in level with the reference plane shown in Figure 9. This plane is in level with the top surface of the camera enclosure, but slices through the center of the lens.


14		Preparing for Installation

Image 26

JAI TS-2030EN, TS-9720EN, TS-1327EN manual Side of Road Installation, Typical side of road installation

Contents

VIS-CAM System Page VIS-CAM System WarrantyCertifications Disclaimer Mailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of Figures Standard configuration of Serial settings for port List of Tables List of Tables VIS-CAM System Xii List of Tables Product overview IntroductionDocument Overview Introduction Traffic Light Sensor TLS300 Preparing for InstallationSystem Components description Back shot VIS installation Viscam Operational Overview Over Lane Positioning Preparing for installationInstallation Preparation Camera height versus trigger distance considerations Camera tilt considerationsAsynchronous triggering considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Side of Road Installation Typical side of road installation Flash and camera distances VIS-CAM System Preparing for Installation Installing the Vehicle Imaging Subsystem Installing the Vehicle Imaging SystemInstalling the TNF-300 Traffic Light Sensor To install the Traffic Light Sensor Light Sensor Cables Wire color SignalMounting pipe and flange Installing the Cameras Optional Side Mount Camera mount template Electrical wiring for the VIS CAM installation X4 Pin # Wire Color Signal Remarks Properly wired X-4 connector 1 X1 and X2 VIS CAM 300/400 VIS-CAM System Installing the J-PanelX1, X2 Pin # Wire Color Signal Remarks VIS CAM connections to the J-Panel TLS 300 to J-Panel connections X7 Pin Power input to the J-Panel X6 Pin # Signal Description Connection to 6 Power input connection 4 X8 LS RS485 Out Connector X8 to converter connector X14 Pin # Signal Description Connection to 5 X14 Trigger Input ConnectorTrigger input connector Trigger polarity Arrow down negative going X15 Pin # Signal Description Connection toX15 Lane Controller Test Trigger Illumination Options Installing the TNF-31 FlashPin Signal Description Connection to Optimal Illumination Distance Between Camera and TNF Installing The Laser Vehicle DetectorTrigger Options Connection for LVD to VIS CAM Wiring for LVD to VIS CAM X7 Pin # Signal Description Connection to VIS-CAM System Installing the Vehicle Imaging Subsystem Preparation for Alignment Pre-Alignment ChecklistSystem Set-Up System Set-Up Typical minimum plate heights and nominal plate heights Validate the Installation GeometryEdit the alignment settings on the Setup Computer Select the Camera to Align Connect the Setup Computer to the Camera Example of a network connection using a local switch Properly Position the License Plate Stand Drive and Park the Setup Vehicle CorrectlyPerform Initial Lens Adjustment and Camera Aiming Initial Camera Alignment Display example Roll Bar Display example Finalize Lens Adjustments and Camera Aiming Perform Final Camera Mount and Lens Adjustments Focus Bar marker display Focus Bar Waveform display Focus Bar Waveform Display with waveform cursors Flash Head Alignment Optimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional and Connector Description Appendix a Camera Functional & Connector Description VIS-CAM System I/O Board Layout Component layout of the EN board Signal levels Connector specificationConnector signal specifications VIS-CAM System X4 I/O Board Connection to J-panel Electrical interface on the I/O board Trigger input Description Connection to Pin Signal Description Panel Remarks Connector physical Interface . Physical interface tablePower input Ethernet Interface Typical wiring diagram I/O Board Flash Connection Description Output signal specificationExternal power requirement Connection DC Flash to an internally powered board VIS-CAM System IO board electrical interface Test Connector physical Interface Physical interface pinouts Connecting the second AC flash VIS-CAM System Night Light TNC 100 Connection X7I/O Board Laser Vehicle Detector Connection Communication Power OutputTrigger Input X1, X3 I/O Board Ethernet Test Connectors Connector physical Interface Connector table Test setup Pin Signal Description Connection to Remarks VIS-CAM System RS485 and power VIS-CAM System X15 I/O Board Auxiliary power connectorCable Specifications Cables Mounting the cables Combined cable Ethernet, RS485 and powerRecommended Cables Page Panel Layout Appendix B J-Panel Functional and Connector DescriptionAppendix B J-Panel Functional & Connector Description X1 J-panel connection to Camera Electrical interface on the J-Panel Signal parameters and conditionsTrigger output Description Connector physical Interface Physical interface table Pin Signal Description Connection to Remarks Board Switches IndicatorsLED indicators Switch labels VIS-CAM System X2 J-panel connection to Camera Board and camera J-panel connection to camera Functionality Signal table Connector physical Interface Ethernet physical connections Category 5 or 6 ethernet wiring diagram Connector switches X3 Light Sensor Connection LED physical indicators X4 Lane Controller Signal to J-Panel #2Connector physical Interface Physical interface connections Databus D0 and D1 X5 Lane Controller Signal from J-Panel #1 Datasignal Physical pin connections J-panel #1 X6, X7 24V DC PowerData signal Principle in the power distribution Connector specification Connector physical Interface RS485 physical connections X11 Ethernet Interface from Camera Connector physical Interface Physical connector description 10 X12 Ethernet Interface from Camera 11 X14 External Trigger External Trigger connection Functionality Trigger 0 Electrical interface on the J-Panel Trigger 1 Electrical interface on the J-Panel Two Lane Controllers 12 X15 Lane Controller interface 6.12.1 FunctionalityCommon Lane Controller Connector physical Interface Wago physical interface Connecting Lane Controller RS485 signal between J-Panels Appendix C Two Cameras, One Flash Configuration Appendix C Two Cameras, One-Flash Configuration Master Flash Connector Slave Laser Connector Master to slave connections Appendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal Blocks VIS-CAM System Appendix D Pluggable Terminal Blocks Basic Settings Appendix E Moxa N-Port 5232 ConfigurationAppendix E Moxa N Port 5232 Configuration Standard configuration of Network Settings Network Settings Standard configuration of Serial settings for port Serial port 1 settings Configuration overview of serial port 1 Data Packing Operating settings portTCP Server Mode VIS-CAM System Appendix F Multiple Moxa N-port Configuration Diagram Appendix F Multiple Moxa N port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Fault Symptom Check/Possible Reason Appendix H TroubleshootingAppendix H Troubleshooting VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa