10 X12 Ethernet Interface from Camera | JAI TS-9720EN, TS-1327EN

VIS-CAM System

6.9.2Connector specification

Connector type:	8 pole shielded RJ45
Connector on board:	Taitek/Kinsun ST3009S-880
Cable part:	Standard RJ45 connector

6.9.3Connector signal specifications

6.9.3 (a) Data signal

Ethernet signals on two pairs (Rx and Tx).

6.9.4Connector physical Interface

Table 31 Physical connector description

Pin	Signal	Description	Connection to

1	Ethernet A+	Ethernet signal	Gigabit switch

2	Ethernet A-	Ethernet signal	Gigabit switch

3	Ethernet B+	Ethernet signal	Gigabit switch

4	(Ethernet C+)	Ethernet signal	Gigabit switch

5	(Ethernet C-)	Ethernet signal	Gigabit switch

6	Ethernet B-	Ethernet signal	Gigabit switch

7	(Ethernet D+)	Ethernet signal	Gigabit switch

8	(Ethernet D-)	Ethernet signal	Gigabit switch

6.10X12: Ethernet Interface from Camera 1

Figure 78. Interface from Camera 1

6.10.1 Functionality

Ethernet interface from Camera 1 to Ethernet switch.

6.10.2 Connector specification

Connector type:	8 pole shielded RJ45
Connector on board:	Taitek/Kinsun ST3009S-880
Cable part:	Standard RJ45 connector


78		Appendix B: J-Panel Functional & Connector Description

Image 90

JAI TS-9720EN manual 10 X12 Ethernet Interface from Camera, Connector physical Interface Physical connector description

Contents

VIS-CAM System Page VIS-CAM System WarrantyCertifications Disclaimer Mailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of Figures Standard configuration of Serial settings for port List of Tables List of Tables VIS-CAM System Xii List of Tables Product overview IntroductionDocument Overview Introduction Preparing for Installation System Components descriptionTraffic Light Sensor TLS300 Back shot VIS installation Viscam Operational Overview Preparing for installation Installation PreparationOver Lane Positioning Camera tilt considerations Asynchronous triggering considerationsCamera height versus trigger distance considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Side of Road Installation Typical side of road installation Flash and camera distances VIS-CAM System Preparing for Installation Installing the Vehicle Imaging Subsystem Installing the Vehicle Imaging SystemInstalling the TNF-300 Traffic Light Sensor To install the Traffic Light Sensor Wire color Signal Mounting pipe and flangeLight Sensor Cables Installing the Cameras Optional Side Mount Camera mount template Electrical wiring for the VIS CAM installation X4 Pin # Wire Color Signal Remarks Properly wired X-4 connector 1 X1 and X2 VIS CAM 300/400 VIS-CAM System Installing the J-PanelX1, X2 Pin # Wire Color Signal Remarks VIS CAM connections to the J-Panel TLS 300 to J-Panel connections X7 Pin Power input to the J-Panel X6 Pin # Signal Description Connection to 6 Power input connection 4 X8 LS RS485 Out Connector X8 to converter connector X14 Pin # Signal Description Connection to 5 X14 Trigger Input ConnectorTrigger input connector Trigger polarity Arrow down negative going X15 Pin # Signal Description Connection toX15 Lane Controller Test Trigger Installing the TNF-31 Flash Pin Signal Description Connection toIllumination Options Installing The Laser Vehicle Detector Trigger OptionsOptimal Illumination Distance Between Camera and TNF Connection for LVD to VIS CAM Wiring for LVD to VIS CAM X7 Pin # Signal Description Connection to VIS-CAM System Installing the Vehicle Imaging Subsystem Preparation for Alignment Pre-Alignment ChecklistSystem Set-Up System Set-Up Typical minimum plate heights and nominal plate heights Validate the Installation GeometryEdit the alignment settings on the Setup Computer Select the Camera to Align Connect the Setup Computer to the Camera Example of a network connection using a local switch Drive and Park the Setup Vehicle Correctly Perform Initial Lens Adjustment and Camera AimingProperly Position the License Plate Stand Initial Camera Alignment Display example Roll Bar Display example Finalize Lens Adjustments and Camera Aiming Perform Final Camera Mount and Lens Adjustments Focus Bar marker display Focus Bar Waveform display Focus Bar Waveform Display with waveform cursors Flash Head Alignment Optimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional and Connector Description Appendix a Camera Functional & Connector Description VIS-CAM System I/O Board Layout Component layout of the EN board Signal levels Connector specificationConnector signal specifications VIS-CAM System X4 I/O Board Connection to J-panel Electrical interface on the I/O board Trigger input Description Connection to Pin Signal Description Panel Remarks Connector physical Interface . Physical interface tablePower input Ethernet Interface Typical wiring diagram I/O Board Flash Connection Output signal specification External power requirementDescription Connection DC Flash to an internally powered board VIS-CAM System IO board electrical interface Test Connector physical Interface Physical interface pinouts Connecting the second AC flash VIS-CAM System Night Light TNC 100 Connection X7I/O Board Laser Vehicle Detector Connection Power Output Trigger InputCommunication X1, X3 I/O Board Ethernet Test Connectors Connector physical Interface Connector table Test setup Pin Signal Description Connection to Remarks VIS-CAM System RS485 and power VIS-CAM System X15 I/O Board Auxiliary power connectorCable Specifications Cables Combined cable Ethernet, RS485 and power Recommended CablesMounting the cables Page Panel Layout Appendix B J-Panel Functional and Connector DescriptionAppendix B J-Panel Functional & Connector Description X1 J-panel connection to Camera Signal parameters and conditions Trigger output DescriptionElectrical interface on the J-Panel Connector physical Interface Physical interface table Pin Signal Description Connection to Remarks Board Switches IndicatorsLED indicators Switch labels VIS-CAM System X2 J-panel connection to Camera Board and camera J-panel connection to camera Functionality Signal table Connector physical Interface Ethernet physical connections Category 5 or 6 ethernet wiring diagram Connector switches X3 Light Sensor Connection LED physical indicators X4 Lane Controller Signal to J-Panel #2Connector physical Interface Physical interface connections Databus D0 and D1 X5 Lane Controller Signal from J-Panel #1 Datasignal X6, X7 24V DC Power Data signalPhysical pin connections J-panel #1 Principle in the power distribution Connector specification Connector physical Interface RS485 physical connections X11 Ethernet Interface from Camera Connector physical Interface Physical connector description 10 X12 Ethernet Interface from Camera 11 X14 External Trigger External Trigger connection Functionality Trigger 0 Electrical interface on the J-Panel Trigger 1 Electrical interface on the J-Panel 12 X15 Lane Controller interface 6.12.1 Functionality Common Lane ControllerTwo Lane Controllers Connector physical Interface Wago physical interface Connecting Lane Controller RS485 signal between J-Panels Appendix C Two Cameras, One Flash Configuration Appendix C Two Cameras, One-Flash Configuration Master Flash Connector Slave Laser Connector Master to slave connections Appendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal Blocks VIS-CAM System Appendix D Pluggable Terminal Blocks Appendix E Moxa N-Port 5232 Configuration Appendix E Moxa N Port 5232 ConfigurationBasic Settings Standard configuration of Network Settings Network Settings Standard configuration of Serial settings for port Serial port 1 settings Configuration overview of serial port 1 Operating settings port TCP Server ModeData Packing VIS-CAM System Appendix F Multiple Moxa N-port Configuration Diagram Appendix F Multiple Moxa N port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Appendix H Troubleshooting Appendix H TroubleshootingFault Symptom Check/Possible Reason VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa