Appendix H Troubleshooting | JAI TS-1327EN, TS-9720EN, TS-2030EN

VIS-CAM System

12		Appendix H: Troubleshooting
		Table 37	Troubleshooting table.

	Fault Symptom				Check/Possible Reason

					Switch S3 on VIS CAM I/O Board is in position “Flash 2” and
	Flash fires only every second time				only one flash is installed to the camera. Set switch S3 to
					position “NIGHT L.”

	Camera(s) does not trigger				Switch S3 and/or S5 is set to the wrong trigger polarity.
	Camera(s) does not trigger				Please refer to section 3.3.6 for setting the switches.
					Please refer to section 3.3.6 for setting the switches.

	Laser connected to IO board connector X7 does not				Check that switch S3 and/or S5 is set to “positive going”
	trigger the camera				(pushed towards X1/X2 connector) on the J-Panel.

Appendix H: Troubleshooting

97

Image 109

JAI TS-1327EN, TS-9720EN, TS-2030EN manual Appendix H Troubleshooting, Fault Symptom Check/Possible Reason

Contents

VIS-CAM System Page Certifications WarrantyVIS-CAM System Disclaimer Mailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of Figures Standard configuration of Serial settings for port List of Tables List of Tables VIS-CAM System Xii List of Tables Document Overview IntroductionProduct overview Introduction System Components description Preparing for InstallationTraffic Light Sensor TLS300 Viscam Back shot VIS installation Operational Overview Installation Preparation Preparing for installationOver Lane Positioning Asynchronous triggering considerations Camera tilt considerationsCamera height versus trigger distance considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Typical side of road installation Side of Road Installation Flash and camera distances VIS-CAM System Preparing for Installation Installing the TNF-300 Traffic Light Sensor Installing the Vehicle Imaging SystemInstalling the Vehicle Imaging Subsystem To install the Traffic Light Sensor Mounting pipe and flange Wire color SignalLight Sensor Cables Optional Side Mount Installing the Cameras Camera mount template X4 Pin # Wire Color Signal Remarks Electrical wiring for the VIS CAM installation Properly wired X-4 connector X1, X2 Pin # Wire Color Signal Remarks VIS-CAM System Installing the J-Panel1 X1 and X2 VIS CAM 300/400 VIS CAM connections to the J-Panel X7 Pin TLS 300 to J-Panel connections X6 Pin # Signal Description Connection to Power input to the J-Panel X8 to converter connector 6 Power input connection 4 X8 LS RS485 Out Connector Trigger input connector 5 X14 Trigger Input ConnectorX14 Pin # Signal Description Connection to Trigger polarity X15 Lane Controller X15 Pin # Signal Description Connection toArrow down negative going Test Trigger Pin Signal Description Connection to Installing the TNF-31 FlashIllumination Options Trigger Options Installing The Laser Vehicle DetectorOptimal Illumination Distance Between Camera and TNF X7 Pin # Signal Description Connection to Connection for LVD to VIS CAM Wiring for LVD to VIS CAM VIS-CAM System Installing the Vehicle Imaging Subsystem System Set-Up Pre-Alignment ChecklistPreparation for Alignment System Set-Up Edit the alignment settings on the Setup Computer Validate the Installation GeometryTypical minimum plate heights and nominal plate heights Select the Camera to Align Example of a network connection using a local switch Connect the Setup Computer to the Camera Perform Initial Lens Adjustment and Camera Aiming Drive and Park the Setup Vehicle CorrectlyProperly Position the License Plate Stand Initial Camera Alignment Display example Roll Bar Display example Perform Final Camera Mount and Lens Adjustments Finalize Lens Adjustments and Camera Aiming Focus Bar marker display Focus Bar Waveform display Flash Head Alignment Focus Bar Waveform Display with waveform cursors Optimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional & Connector Description Appendix a Camera Functional and Connector Description Component layout of the EN board VIS-CAM System I/O Board Layout Connector signal specifications Connector specificationSignal levels VIS-CAM System X4 I/O Board Connection to J-panel Trigger input Description Electrical interface on the I/O board Power input Connector physical Interface . Physical interface tableConnection to Pin Signal Description Panel Remarks Ethernet Interface I/O Board Flash Connection Typical wiring diagram External power requirement Output signal specificationDescription Connection DC Flash to an internally powered board VIS-CAM System Test IO board electrical interface Physical interface pinouts Connector physical Interface Connecting the second AC flash X7I/O Board Laser Vehicle Detector Connection VIS-CAM System Night Light TNC 100 Connection Trigger Input Power OutputCommunication Connector physical Interface Connector table X1, X3 I/O Board Ethernet Test Connectors Pin Signal Description Connection to Remarks Test setup VIS-CAM System Cable Specifications VIS-CAM System X15 I/O Board Auxiliary power connectorRS485 and power Cables Recommended Cables Combined cable Ethernet, RS485 and powerMounting the cables Page Appendix B J-Panel Functional & Connector Description Appendix B J-Panel Functional and Connector DescriptionPanel Layout X1 J-panel connection to Camera Trigger output Description Signal parameters and conditionsElectrical interface on the J-Panel Pin Signal Description Connection to Remarks Board Connector physical Interface Physical interface table LED indicators IndicatorsSwitches Switch labels Board and camera J-panel connection to camera Functionality VIS-CAM System X2 J-panel connection to Camera Signal table Category 5 or 6 ethernet wiring diagram Connector physical Interface Ethernet physical connections X3 Light Sensor Connection Connector switches Connector physical Interface Physical interface connections X4 Lane Controller Signal to J-Panel #2LED physical indicators Databus D0 and D1 Datasignal X5 Lane Controller Signal from J-Panel #1 Data signal X6, X7 24V DC PowerPhysical pin connections J-panel #1 Principle in the power distribution Connector specification X11 Ethernet Interface from Camera Connector physical Interface RS485 physical connections 10 X12 Ethernet Interface from Camera Connector physical Interface Physical connector description External Trigger connection Functionality 11 X14 External Trigger Trigger 1 Electrical interface on the J-Panel Trigger 0 Electrical interface on the J-Panel Common Lane Controller 12 X15 Lane Controller interface 6.12.1 FunctionalityTwo Lane Controllers Connecting Lane Controller RS485 signal between J-Panels Connector physical Interface Wago physical interface Appendix C Two Cameras, One-Flash Configuration Appendix C Two Cameras, One Flash Configuration Master to slave connections Master Flash Connector Slave Laser Connector Appendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal Blocks VIS-CAM System Appendix D Pluggable Terminal Blocks Appendix E Moxa N Port 5232 Configuration Appendix E Moxa N-Port 5232 ConfigurationBasic Settings Network Settings Standard configuration of Network Settings Serial port 1 settings Standard configuration of Serial settings for port Configuration overview of serial port 1 TCP Server Mode Operating settings portData Packing VIS-CAM System Appendix F Multiple Moxa N port Configuration Diagram Appendix F Multiple Moxa N-port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Appendix H Troubleshooting Appendix H TroubleshootingFault Symptom Check/Possible Reason VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa