X11 Ethernet Interface from Camera | JAI TS-2030EN, TS-9720EN

VIS-CAM System

6.8.2Connector specification

Connector type:	8 pole WAGO pluggable terminal block
Connector on board:	WAGO 734-238
Cable part:	WAGO 734-208

6.8.3Connector signal specifications

6.8.3 (a) Power output

Voltage:	24	V DC from power supply connected to X6 or X7
	12	V DC from regulator on board
Current:	0.3A fused

6.8.3 (b) Databus D0 and D1

D0 and D1 are RS485 databus signals from the light sensor.

6.8.4Connector physical Interface

Table 30 RS485 physical connections

Pin	Signal	Description	Connection to

1	24V dc	24v Power output

2	Gnd	Power return

3	+12V dc	12V power output

4	Gnd	Power return

5	D0+	RS485 databus D0+

6	D0-	RS485 databus D0-

7	D1+	RS485 databus D1+

8	D1-	RS485 databus D1+

6.9X11: Ethernet Interface from Camera 0

Figure 77. Interface from Camera 0

6.9.1Functionality

Ethernet interface from Camera 0 to Ethernet switch.

Appendix B: J-Panel Functional & Connector Description

77

Image 89

JAI TS-2030EN, TS-9720EN manual X11 Ethernet Interface from Camera, Connector physical Interface RS485 physical connections

Contents

VIS-CAM System Page Certifications WarrantyVIS-CAM System Disclaimer Mailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents Connector signal specifications Connector physical Interface Table of Contents Vii VIS-CAM System Viii Table of Contents List of Figures List of Figures Standard configuration of Serial settings for port List of Tables List of Tables VIS-CAM System Xii List of Tables Document Overview IntroductionProduct overview Introduction Traffic Light Sensor TLS300 Preparing for InstallationSystem Components description Viscam Back shot VIS installation Operational Overview Over Lane Positioning Preparing for installationInstallation Preparation Camera height versus trigger distance considerations Camera tilt considerationsAsynchronous triggering considerations VIS-CAM System VIS 300 U.S. Camera options chart VIS 350 U.S. Camera options chart VIS 400 U.S. Camera options chart VIS 300 European Camera options chart VIS 350 European Camera options chart VIS 400 European Camera options chart Typical side of road installation Side of Road Installation Flash and camera distances VIS-CAM System Preparing for Installation Installing the TNF-300 Traffic Light Sensor Installing the Vehicle Imaging SystemInstalling the Vehicle Imaging Subsystem To install the Traffic Light Sensor Light Sensor Cables Wire color SignalMounting pipe and flange Optional Side Mount Installing the Cameras Camera mount template X4 Pin # Wire Color Signal Remarks Electrical wiring for the VIS CAM installation Properly wired X-4 connector X1, X2 Pin # Wire Color Signal Remarks VIS-CAM System Installing the J-Panel1 X1 and X2 VIS CAM 300/400 VIS CAM connections to the J-Panel X7 Pin TLS 300 to J-Panel connections X6 Pin # Signal Description Connection to Power input to the J-Panel X8 to converter connector 6 Power input connection 4 X8 LS RS485 Out Connector Trigger input connector 5 X14 Trigger Input ConnectorX14 Pin # Signal Description Connection to Trigger polarity X15 Lane Controller X15 Pin # Signal Description Connection toArrow down negative going Test Trigger Illumination Options Installing the TNF-31 FlashPin Signal Description Connection to Optimal Illumination Distance Between Camera and TNF Installing The Laser Vehicle DetectorTrigger Options X7 Pin # Signal Description Connection to Connection for LVD to VIS CAM Wiring for LVD to VIS CAM VIS-CAM System Installing the Vehicle Imaging Subsystem System Set-Up Pre-Alignment ChecklistPreparation for Alignment System Set-Up Edit the alignment settings on the Setup Computer Validate the Installation GeometryTypical minimum plate heights and nominal plate heights Select the Camera to Align Example of a network connection using a local switch Connect the Setup Computer to the Camera Properly Position the License Plate Stand Drive and Park the Setup Vehicle CorrectlyPerform Initial Lens Adjustment and Camera Aiming Initial Camera Alignment Display example Roll Bar Display example Perform Final Camera Mount and Lens Adjustments Finalize Lens Adjustments and Camera Aiming Focus Bar marker display Focus Bar Waveform display Flash Head Alignment Focus Bar Waveform Display with waveform cursors Optimal Illumination Distance Between Camera and TNF VIS-CAM System System Set-Up Appendix a Camera Functional & Connector Description Appendix a Camera Functional and Connector Description Component layout of the EN board VIS-CAM System I/O Board Layout Connector signal specifications Connector specificationSignal levels VIS-CAM System X4 I/O Board Connection to J-panel Trigger input Description Electrical interface on the I/O board Power input Connector physical Interface . Physical interface tableConnection to Pin Signal Description Panel Remarks Ethernet Interface I/O Board Flash Connection Typical wiring diagram Description Output signal specificationExternal power requirement Connection DC Flash to an internally powered board VIS-CAM System Test IO board electrical interface Physical interface pinouts Connector physical Interface Connecting the second AC flash X7I/O Board Laser Vehicle Detector Connection VIS-CAM System Night Light TNC 100 Connection Communication Power OutputTrigger Input Connector physical Interface Connector table X1, X3 I/O Board Ethernet Test Connectors Pin Signal Description Connection to Remarks Test setup VIS-CAM System Cable Specifications VIS-CAM System X15 I/O Board Auxiliary power connectorRS485 and power Cables Mounting the cables Combined cable Ethernet, RS485 and powerRecommended Cables Page Appendix B J-Panel Functional & Connector Description Appendix B J-Panel Functional and Connector DescriptionPanel Layout X1 J-panel connection to Camera Electrical interface on the J-Panel Signal parameters and conditionsTrigger output Description Pin Signal Description Connection to Remarks Board Connector physical Interface Physical interface table LED indicators IndicatorsSwitches Switch labels Board and camera J-panel connection to camera Functionality VIS-CAM System X2 J-panel connection to Camera Signal table Category 5 or 6 ethernet wiring diagram Connector physical Interface Ethernet physical connections X3 Light Sensor Connection Connector switches Connector physical Interface Physical interface connections X4 Lane Controller Signal to J-Panel #2LED physical indicators Databus D0 and D1 Datasignal X5 Lane Controller Signal from J-Panel #1 Physical pin connections J-panel #1 X6, X7 24V DC PowerData signal Principle in the power distribution Connector specification X11 Ethernet Interface from Camera Connector physical Interface RS485 physical connections 10 X12 Ethernet Interface from Camera Connector physical Interface Physical connector description External Trigger connection Functionality 11 X14 External Trigger Trigger 1 Electrical interface on the J-Panel Trigger 0 Electrical interface on the J-Panel Two Lane Controllers 12 X15 Lane Controller interface 6.12.1 FunctionalityCommon Lane Controller Connecting Lane Controller RS485 signal between J-Panels Connector physical Interface Wago physical interface Appendix C Two Cameras, One-Flash Configuration Appendix C Two Cameras, One Flash Configuration Master to slave connections Master Flash Connector Slave Laser Connector Appendix D Pluggable Terminal Blocks Appendix D Pluggable Terminal Blocks VIS-CAM System Appendix D Pluggable Terminal Blocks Basic Settings Appendix E Moxa N-Port 5232 ConfigurationAppendix E Moxa N Port 5232 Configuration Network Settings Standard configuration of Network Settings Serial port 1 settings Standard configuration of Serial settings for port Configuration overview of serial port 1 Data Packing Operating settings portTCP Server Mode VIS-CAM System Appendix F Multiple Moxa N port Configuration Diagram Appendix F Multiple Moxa N-port Configuration DiagramPage Appendix G Ethernet Requirements Appendix G Ethernet RequirementsPage Fault Symptom Check/Possible Reason Appendix H TroubleshootingAppendix H Troubleshooting VIS-CAM System Appendix H Troubleshooting VIS-CAM System Europe, Middle East & Africa