Table B-2 Parallel Connector Pin Assignment | Kyocera FS-1920

Parallel Interface

Pin	In/out	Description
1	In	Strobe* [nStrobe]

2	In/Out	Data 0 [Data 1]

3	In/Out	Data 1 [Data 2]

4	In/Out	Data 2 [Data 3]

5	In/Out	Data 3 [Data 4]

6	In/Out	Data 4 [Data 5]

7	In/Out	Data 5 [Data 6]

8	In/Out	Data 6 [Data 7]

9	In/Out	Data 7 [Data 8]

10	Out	Acknowledge* [nAck]

11	Out	Busy [Busy]

12	Out	Paper Empty [PError], returns paper empty status if FRPO
		O2=2

13	Out	Select (Online) [nSelect], returns off-line status if FRPO O2=2

14	In	Auto-feed [nAutoFd]

15	-	Not connected

16	-	0 V DC

17	-	Chassis GND

18	-	+5 V DC

19	-	Ground

20	-	Ground

21	-	Ground

22	-	Ground

23	-	Ground

24	-	Ground

25	-	Ground

26	-	Ground

27	-	Ground

28	-	Ground

29	-	Ground

30	-	Ground

31	In	Ignored [nInit]

32	Out	Error*, returns error status if FRPO O2=2 [nFault]

33	-	Not connected

34	-	Not connected

35	Out	Power Ready

36	In	Ignored [nSelectIn]

Table B-2 Parallel Connector Pin Assignment

[ ]: Signal names in the Auto mode and Nibble (high) mode (IEEE1284). In the Auto mode and Nibble (high) mode, these signals are bi-directional.

B-3

Image 207

Kyocera FS-1920 manual Table B-2 Parallel Connector Pin Assignment, Pin In/out Description

Contents

FS-1920 Regarding Tradenames General Limited WarrantyLicense Limitation of Remedies Agfa Japan License Agreement Typeface Trademark Acknowledgement Contents Contents Paper Selection Maintenance Appendix B Host Computer Interface TroubleshootingFonts Appendix a Options Glossary Glossary-1 Index Index-1 Introduction Features KPDL3 Kyocera Printer Description Language USB Universal Serial Bus InterfaceMPS Printer control language Prescribe CompactFlash card slot for option fonts, macros, forms, etc Snmp complianceSupport for network printer monitor utility KM-NET Viewer Description For More Information Guide to the Operation Guide Option Using the Operator Panel Understanding the Operator Panel Message DisplayMessage Meaning Interface Indicator Paper Size IndicatorMessage Paper Size Display Message Display Paper Type Paper Type IndicatorREADY, DATA, and Attention Indicators Indicator Description Key Function Keys Menu System Road Map Over operator panel settings TCP/IP IBM KIR A4/LT Off Printer Reset Resource Prot Permanent Perm / Temp Buzzer Print Menu Map ? Printing Test PagesMenu Map Print Menu Map Sample Menu MAP Menu MAP Status Print StatusPrint Status Page ? Status Hardware Information Installation OptionsError Log Software Version KIR Test Pattern Interface Information Service Status ServiceOthers Network Card Interface Status Opt. StatusPage ? Off Opt. StatusPage ? OnOpt. StatusPage On List Font ListsFont Font Select Internal Prescribe Font Lists Processing Waiting Received Data DumpingPrint HEX-DUMP Print HEX-DUMP? Setting the Paper Size Setting the Paper Size in Paper CassettePaper Handling Custom Paper Size Paper Handling Cassette Size Custom Unit ? mm Unit mm Dimension 216 mm DimensionSetting the Paper Size in MP Tray MP Tray Size ? A4 MP Tray Size A4 Cassette Type ? Plain Setting the Paper TypeSetting the Paper Type in Paper Cassette Cassette Type Plain Setting the Paper Type in MP Tray MP Tray Type PlainMP Tray Type ? Plain Creating Custom Paper Type Type Adjust Custom Paper Handling Paper Weight Normal Paper Weight ? NormalSetting the Paper Weight Duplex path Enable Duplex path ? EnableSetting the Duplex Path Reset Type Adjust Reset Type Adjust ?Resetting the Custom Paper Type MP Tray Mode Cassette MP Tray Mode Feed Select ? Cassette MP Tray Mode ? CassetteSelecting the Paper Feed Source Feed Select Cassette Selecting the Output Stack Stack Select Top tray FaceDnStack Select Overriding A4 and Letter Size Difference Override A4/LT OffOverride A4/LT ? Off Changing the Emulation PaginationEmulation Emulation ?PCL Alternative Emulation for Kpdl Emulation EmulationEmulation ?KPDL Auto Alt. Emulation ?PCL ?KPDL Printing Kpdl Errors Default font Print Kpdl Errs ? OnFont I000 ?I000Letter Description Default Font Size Size PointsSize Changing Type for Courier/Letter Gothic Courier Regular Pitch Setting the Character Pitch for Courier/Letter Gothic Code Set Code SetCode Set ?IBM PC-8 Number of Copies SetCopies 001 Printing Orientation Orientation PortraitOrientation ? Portrait Status KIR Checking Lines KIR Kyocera Image Refinement KIR Mode KIR Mode ? OnPrint Quality EcoPrint Mode Off EcoPrint Mode ? OffEcoprint Resolution Resolution Fast 1200 modeResolution Mode Quick Copy Proof and Hold Private Print Stored Job MPSJob Retention Job Storage Printing Additional Copies using Quick CopyQuick Copy MPS Arlen ?Report Quick Copy HaroldQuick Copy ?Harold Quick Copy ?Arlen Printing Remaining Copies of a Proof and Hold Job Report DeleteProof and Hold Deleting a Quick Copy Job Quick Copy Private/Stored ?Arlen Printing a Private JobPrivate/Stored Harold Private/Stored ?Harold Agenda Delete AgendaAgenda Copies Agenda Copies 001 Releasing a Stored Job Printing a Stored Job Deleting a Stored Job KM-Net Job Manager Printing a Code Job MPS Printing a List of Code Jobs List of Code JOBList of Code JOB ? Retrieving Jobs from Virtual Mailbox VMB Print VMB Data Tray001Tray001? Printing a List of VMB List of VMBList of VMB ? MPS Configuration MPS Configuration Maximum Space Assigned to Temporary Code Jobs Temp. Code JOB Size 050MB Perm. Code JOB Size 050MB Size 05 0MBMaximum Space Assigned to Permanent Code Jobs VMB Size 050MB VMB SizeMaximum Space Assigned to Virtual Mailboxes Interface Parallel Interface Mode USB Interface Mode Parallel I/F ? AutoInterface ? USB Interface ? Serial Serial Interface Parameters Baud Rate Baud Rate Data BitsStop Bits Parity None Protocol DTRpos.&XON Network Interface Parameters NetWare EtherTalk Off Opt. StatusPage OnTCP/IP ? On TCP/IP On Dhcp Off IP Address Subnet Mask Gateway 000.000.000.000 RAM Disk Mode Off Operating the Storage DeviceActivating the RAM Disk RAM Disk Size Mbyte RAM Disk Mode ? On Read Data ?data name Reading DataMemory Card Read Data Data name Writing Data Write DataWrite Data ? Write Information Deleting Data Delete Data data nameDelete Data ?data name Reading Fonts from a CompactFlash Card Read FontsRead Fonts ? Formatting a Storage Device FormatFormat ? List of Partitions Printing a List of Data Names Partition List List Partitions ? Configuration Protect ModeProtect LF Action LF only Protect ? OnProtect ? Auto Linefeed LF Action Carriage-Return CR Action CR Action CR onlyCR Action ? CR only Wide A4 Pitch Wide A4 OffWide A4 ? Off Print Density Print Density Life Counters Toner Counter ResettingNew Toner Installed Total Printed Pages MSG Language ? English New Toner Installed ?Message Language MSG Language English Following order The key cycles in the reverse order Form Feed Time Out 030sec Automatic Form Feed Timeout Sleep Timer Setting Sleep Timer 015 minSleep Timer Turning Off the Sleep Timer Sleep ModeSleep Mode ? On Sleep Mode ? Off Self test Please wait Ready Printer ResettingPrinter Reset Printer Reset ? Resource Protection Resource Prot OffResource Prot ? Off Alarm Buzzer Setting Buzzer OnBuzzer ? On Auto Continue Setting Auto Continue Mode OnAuto Continue Mode ? On Timer Setting the Auto Continue Recovery TimeAuto Continue Duplex ? Off Duplex Printing Error Detection SettingFinishing Error Duplex Off Paper Selection Paper Availability Paper SpecificationsSpecification General Guidelines Selecting the Right Paper Condition of the PaperComposition Multi-purpose Size Cassette or Tray Basis WeightPaper Size Smoothness Weight g/m² Paper Weight Equivalence TableMoisture Content Bond Weight lb Europe Metric Other Paper Properties Paper Grain Special Paper Transparency Overhead Projection FilmPaper type Media type Adhesive-Backed Labels Envelopes Postcards Thick Paper Colored Paper Preprinted PaperRecycled Paper Paper Type Maintenance Toner Container Replacement Interval Toner Container Replacement Replenishing Toner Carefully remove the protective seal orange colored Push Here Replacing the Waste Toner Box Waste Toner Box Replacement Cap the waste toner box after removing from the printer Toner Counter Resetting on Cleaning the Charger Wire Cleaning Pull out the charger unit approximately 5 cm 2 inches Cleaning the Charger Grid Shown in the figure Cleaner is not re-usable Paper Transfer Unit Ramp using the wiper cloth included in the toner kit Troubleshooting General Guide Symptom Check Items Corrective Action Print Quality Problems Check the Ecoprint setting Check the charger unit installationCheck the print density Check the paper chute and the ramp Check the transfer rollerCheck the file or program Indicators and Messages IndicatorsIndicator Name Condition Description Message Corrective Action Maintenance Messages Key. See Correcting a Paper Jam on Unnecessary fonts and macros. See Appendix a See Operating the Storage Device on Error Messages From the operator panel, and re-select Auto Beginning to ensure correct reading of the memory card Paper jam Description Reference Message Location Correcting a Paper Jam Jam recovery Jam at the Paper Cassette or Inside the Printer Shown in B Pull out the duplex drawer Paper Jam at the Option Duplexer Remove the jammed paper Paper Jam at the Option Sorter Close the rear cover of the option sorter Jam at the MP Tray Fonts PCL Scalable and Bitmap Fonts List of Fonts List of Fonts List of Fonts Kpdl Fonts Kpdl Fonts Appendix a Options 6Paper Feeder Available Options Expanding the Printer Memory Removing the Main Circuit Board YES no Circuit board, can cause serious damage to the printer Dimm to be used Installing Dimm Removing Dimm Testing the Expansion Memory Adjusting the Memory on the Printer Driver PF-60 Paper Feeder Installing Option Units Installing Option Units Load paper DU-61 Duplexer Gently place the printer on top of the duplexer Pass the connected cable and power cord through the opening SO-60 Sorter Cord, and printer cable Push the sorter down. The levers of the attachment legs are Grip Duplexer Rear Cover Do not move or lift the printer with the sorter installed EF-60 Envelope Feeder Installing the envelope feeder on the printer Load envelopes into the envelope feeder Pull out the sub-tray that matches the size of the envelopes Paper Setting Button PT-4/PT-60 Rear Tray Install the rear tray on the rear of the printer Network Interface Card About the modes, see Network Interface Parameters on Microdrive Hard Disk Return the main circuit board to the printer by reversing CompactFlash Memory Card Appendix B Host Computer Interface Parallel Interface Communication Modes Interface SignalsCommunication Reception Transmission Mode Parallel Interface Pin In/out Description Table B-2 Parallel Connector Pin Assignment Acknowledge* nAck Pin USB Interface Specifications RS-232C Interface Interface SignalsPin In/out Signal Description Serial Interface Option RS-232C Protocol Table B-5Parameter value Baud rate Table B-6 Table B-7Parameter value Meaning Table B-8 Prescribe Frpo D0 Command Connecting the Printer to the Computer RS-232C Cable ConnectionObtain a Suitable RS-232C Cable Double click on Communications Port RS-232C Cable Connection DOS, enter the following commands Appendix C Specifications Table C-1 Description Ambient conditions Power requirementsPower consumption Pressure level at the front Dimensions Glossary Dpi dots per inch Cassette modeFirst mode IEEE1284 Parallel interface Sleep modeOperator panel Outline font Index Index-2 Index-3 2003 Is a trademark of Kyocera Corporation