Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-1920 manual Selecting the Output Stack, Stack Select Top tray FaceDn

Models: FS-1920

1 227

Download 227 pages 18.74 Kb

Page 55

Paper Handling

Selecting the Output Stack

The following procedure allows you to select whether printouts will be received by the top tray or to the rear tray. If an option sorter is installed, it can also be selected using the manner described below.

1

2

3

4

Press the MENU key.

Press the or key repeatedly until Paper Handling > appears.

Paper Handling >

Press the > key.

Press the or key repeatedly until >Stack Select appears.

>Stack Select Top tray FaceDn

5	Press the ENTER key. A blinking question mark (?) appears.
		>Stack Select
6			?Top tray FaceDn

	Press the or key to display the desired destination. The output
	tray changes as shown below.

7

8

Top tray FaceDn (Printer’s top tray) [Default]

RearTray FaceUp (Printer’s rear tray) [Option rear tray required] Sorter FaceDn [Option sorter required]

When the desired paper source displayed, press the ENTER key.

Press the MENU key. The message display returns to Ready.

1-39

Image 55

Kyocera FS-1920 manual Selecting the Output Stack, Stack Select Top tray FaceDn

Contents

FS-1920 Regarding Tradenames General Limited WarrantyLicense Limitation of RemediesAgfa Japan License Agreement Typeface Trademark AcknowledgementContents Contents Paper Selection MaintenanceAppendix B Host Computer Interface TroubleshootingFonts Appendix a OptionsGlossary Glossary-1 Index Index-1 Introduction Features KPDL3 Kyocera Printer Description Language USB Universal Serial Bus InterfaceMPS Printer control language PrescribeSnmp compliance CompactFlash card slot for option fonts, macros, forms, etcSupport for network printer monitor utility KM-NET Viewer Description For More InformationGuide to the Operation Guide Option Using the Operator Panel Message Display Understanding the Operator PanelMessage Meaning Paper Size Indicator Interface IndicatorMessage Paper Size Display Message Display Paper Type Paper Type IndicatorREADY, DATA, and Attention Indicators Indicator DescriptionKey Function KeysMenu System Road Map Over operator panel settingsTCP/IP IBM KIR A4/LT Off Printer Reset Resource Prot Permanent Perm / Temp Buzzer Print Menu Map ? Printing Test PagesMenu Map Print Menu MapSample Menu MAP Menu MAPPrint Status StatusPrint Status Page ? Status Hardware Information Installation OptionsError Log Software VersionKIR Test Pattern Interface InformationService Service StatusOthers Network Card Interface Status Opt. StatusPage ? On Opt. StatusPage ? OffOpt. StatusPage On List Font ListsFont Font Select InternalPrescribe Font ListsProcessing Waiting Received Data DumpingPrint HEX-DUMP Print HEX-DUMP?Setting the Paper Size in Paper Cassette Setting the Paper SizePaper Handling Custom Paper Size Paper HandlingCassette Size Custom Unit ? mm Unit mmDimension Dimension 216 mmSetting the Paper Size in MP Tray MP Tray Size ? A4 MP Tray Size A4Cassette Type ? Plain Setting the Paper TypeSetting the Paper Type in Paper Cassette Cassette Type PlainMP Tray Type Plain Setting the Paper Type in MP TrayMP Tray Type ? Plain Creating Custom Paper Type Type Adjust CustomPaper Handling Paper Weight ? Normal Paper Weight NormalSetting the Paper Weight Duplex path ? Enable Duplex path EnableSetting the Duplex Path Reset Type Adjust ? Reset Type AdjustResetting the Custom Paper Type MP Tray Mode Cassette MP Tray ModeFeed Select ? Cassette MP Tray Mode ? CassetteSelecting the Paper Feed Source Feed Select CassetteStack Select Top tray FaceDn Selecting the Output StackStack Select Override A4/LT Off Overriding A4 and Letter Size DifferenceOverride A4/LT ? Off Changing the Emulation PaginationEmulation Emulation ?PCLAlternative Emulation for Kpdl Emulation EmulationEmulation ?KPDL Auto Alt. Emulation ?PCL?KPDL Printing Kpdl ErrorsPrint Kpdl Errs ? On Default fontFont ?I000 I000Letter Description Size Points Default Font SizeSize Changing Type for Courier/Letter Gothic Courier RegularPitch Setting the Character Pitch for Courier/Letter GothicCode Set Code SetCode Set ?IBM PC-8 Set Number of CopiesCopies 001 Orientation Portrait Printing OrientationOrientation ? Portrait Status KIR Checking Lines KIR Kyocera Image RefinementKIR Mode ? On KIR ModePrint Quality EcoPrint Mode ? Off EcoPrint Mode OffEcoprint Resolution Fast 1200 mode ResolutionResolution MPS Mode Quick Copy Proof and Hold Private Print Stored JobJob Retention Job Storage Printing Additional Copies using Quick CopyQuick Copy MPSArlen ?Report Quick Copy HaroldQuick Copy ?Harold Quick Copy ?ArlenPrinting Remaining Copies of a Proof and Hold Job Report DeleteProof and Hold Deleting a Quick Copy JobQuick Copy Private/Stored ?Arlen Printing a Private JobPrivate/Stored Harold Private/Stored ?HaroldAgenda Delete AgendaAgenda Copies Agenda Copies 001Releasing a Stored Job Printing a Stored JobDeleting a Stored Job KM-Net Job Manager Printing a Code JobMPS List of Code JOB Printing a List of Code JobsList of Code JOB ? Print VMB Data Tray001 Retrieving Jobs from Virtual Mailbox VMBTray001? List of VMB Printing a List of VMBList of VMB ? MPS Configuration MPS ConfigurationMaximum Space Assigned to Temporary Code Jobs Temp. Code JOB Size 050MBSize 05 0MB Perm. Code JOB Size 050MBMaximum Space Assigned to Permanent Code Jobs VMB Size VMB Size 050MBMaximum Space Assigned to Virtual Mailboxes Interface Parallel Interface ModeParallel I/F ? Auto USB Interface ModeInterface ? USB Interface ? Serial Serial Interface ParametersBaud Rate Baud Rate Data BitsStop Bits Parity None Protocol DTRpos.&XONNetwork Interface Parameters EtherTalk Off Opt. StatusPage On NetWareTCP/IP ? On TCP/IP On Dhcp Off IP Address Subnet Mask Gateway 000.000.000.000 Operating the Storage Device RAM Disk Mode OffActivating the RAM Disk RAM Disk Size Mbyte RAM Disk Mode ? OnRead Data ?data name Reading DataMemory Card Read Data Data nameWrite Data Writing DataWrite Data ? Write Information Delete Data data name Deleting DataDelete Data ?data name Read Fonts Reading Fonts from a CompactFlash CardRead Fonts ? Format Formatting a Storage DeviceFormat ? List of Partitions Printing a List of Data NamesPartition List List Partitions ?Protect Mode ConfigurationProtect LF Action LF only Protect ? OnProtect ? Auto Linefeed LF ActionCR Action CR only Carriage-Return CR ActionCR Action ? CR only Wide A4 Off Wide A4 PitchWide A4 ? Off Print Density Print DensityLife Counters Toner Counter ResettingNew Toner Installed Total Printed PagesMSG Language ? English New Toner Installed ?Message Language MSG Language EnglishFollowing order The key cycles in the reverse order Form Feed Time Out 030sec Automatic Form Feed TimeoutSleep Timer 015 min Sleep Timer SettingSleep Timer Turning Off the Sleep Timer Sleep ModeSleep Mode ? On Sleep Mode ? OffSelf test Please wait Ready Printer ResettingPrinter Reset Printer Reset ?Resource Prot Off Resource ProtectionResource Prot ? Off Buzzer On Alarm Buzzer SettingBuzzer ? On Auto Continue Mode On Auto Continue SettingAuto Continue Mode ? On Setting the Auto Continue Recovery Time TimerAuto Continue Duplex ? Off Duplex Printing Error Detection SettingFinishing Error Duplex OffPaper Selection Paper Availability Paper SpecificationsSpecification General GuidelinesCondition of the Paper Selecting the Right PaperComposition Multi-purpose Size Cassette or Tray Basis WeightPaper Size SmoothnessWeight g/m² Paper Weight Equivalence TableMoisture Content Bond Weight lb Europe MetricOther Paper Properties Paper GrainTransparency Overhead Projection Film Special PaperPaper type Media type Adhesive-Backed Labels Envelopes PostcardsThick Paper Preprinted Paper Colored PaperRecycled Paper Paper Type Maintenance Toner Container Replacement Interval Toner Container ReplacementReplenishing Toner Carefully remove the protective seal orange colored Push Here Replacing the Waste Toner Box Waste Toner Box ReplacementCap the waste toner box after removing from the printer Toner Counter Resetting on Cleaning the Charger Wire CleaningPull out the charger unit approximately 5 cm 2 inches Cleaning the Charger GridShown in the figure Cleaner is not re-usable Paper Transfer Unit Ramp using the wiper cloth included in the toner kitTroubleshooting General Guide Symptom Check Items Corrective ActionPrint Quality Problems Check the charger unit installation Check the Ecoprint settingCheck the print density Check the transfer roller Check the paper chute and the rampCheck the file or program Indicators Indicators and MessagesIndicator Name Condition Description Message Corrective Action Maintenance MessagesKey. See Correcting a Paper Jam on Unnecessary fonts and macros. See Appendix a See Operating the Storage Device on Error MessagesFrom the operator panel, and re-select Auto Beginning to ensure correct reading of the memory cardPaper jam Description Reference Message Location Correcting a Paper JamJam recovery Jam at the Paper Cassette or Inside the Printer Shown in B Pull out the duplex drawer Paper Jam at the Option DuplexerRemove the jammed paper Paper Jam at the Option Sorter Close the rear cover of the option sorter Jam at the MP Tray Fonts PCL Scalable and Bitmap Fonts List of FontsList of Fonts List of Fonts Kpdl Fonts Kpdl Fonts Appendix a Options 6Paper Feeder Available OptionsExpanding the Printer Memory Removing the Main Circuit Board YES noCircuit board, can cause serious damage to the printer Dimm to be used Installing DimmRemoving Dimm Testing the Expansion MemoryAdjusting the Memory on the Printer Driver PF-60 Paper Feeder Installing Option UnitsInstalling Option Units Load paper DU-61 Duplexer Gently place the printer on top of the duplexer Pass the connected cable and power cord through the opening SO-60 Sorter Cord, and printer cable Push the sorter down. The levers of the attachment legs are Grip Duplexer Rear Cover Do not move or lift the printer with the sorter installed EF-60 Envelope Feeder Installing the envelope feeder on the printerLoad envelopes into the envelope feeder Pull out the sub-tray that matches the size of the envelopes Paper Setting Button PT-4/PT-60 Rear Tray Install the rear tray on the rear of the printerNetwork Interface Card About the modes, see Network Interface Parameters on Microdrive Hard Disk Return the main circuit board to the printer by reversing CompactFlash Memory Card Appendix B Host Computer Interface Parallel Interface Communication Modes Interface SignalsCommunication Reception Transmission Mode Parallel InterfacePin In/out Description Table B-2 Parallel Connector Pin AssignmentAcknowledge* nAck Pin USB Interface SpecificationsRS-232C Interface Interface SignalsPin In/out Signal Description Serial Interface OptionTable B-5 RS-232C ProtocolParameter value Baud rate Table B-7 Table B-6Parameter value Meaning Table B-8 Prescribe Frpo D0 CommandRS-232C Cable Connection Connecting the Printer to the ComputerObtain a Suitable RS-232C Cable Double click on Communications Port RS-232C Cable Connection DOS, enter the following commands Appendix C Specifications Table C-1 Description Ambient conditions Power requirementsPower consumption Pressure level at the front DimensionsGlossary Dpi dots per inch Cassette modeFirst mode IEEE1284Parallel interface Sleep modeOperator panel Outline fontIndex Index-2 Index-3 2003 Is a trademark of Kyocera Corporation