Network Interface Parameters, Interface ? Option | Kyocera FS-1920

Interface

Network Interface Parameters

This section applies to the printers having the option network card installed.

Option	To make your printer supports TCP/IP, Netware, and EtherTalk networks,

	you will need to install the option network interface card in the printer and
	make the proper settings as explained in this section.
	Using the operator panel, you can:
	• Activate or deactivate TCP/IP, NetWare, and EtherTalk
	• Activate or deactivate DHCP
	• Enter IP address, subnet mask address, and default gateway address
	To confirm or change network card parameters, proceed as follows:

1

2

3

4

5

Press the MENU key.

Press the or key repeatedly until Interface > appears. One of the interface names shown below appears, indicating the current interface.

Parallel (default)

USB

Serial (when a serial interface board kit is installed) Option (when a network interface card is installed)

Press the ENTER key. A blinking question mark (?) appears.

Interface

? Parallel

Press the or key repeatedly until Option appears.

Interface

? Option

Press the ENTER key again.

1-78

Image 94

Kyocera FS-1920 manual Network Interface Parameters, Interface ? Option

Contents

FS-1920 Regarding Tradenames Limitation of Remedies Limited WarrantyLicense General Typeface Trademark Acknowledgement Agfa Japan License Agreement Contents Contents Maintenance Paper Selection Appendix a Options TroubleshootingFonts Appendix B Host Computer Interface Glossary Glossary-1 Index Index-1 Introduction Features Printer control language Prescribe USB Universal Serial Bus InterfaceMPS KPDL3 Kyocera Printer Description Language Snmp compliance CompactFlash card slot for option fonts, macros, forms, etcSupport for network printer monitor utility KM-NET Viewer For More Information Description Guide to the Operation Guide Option Using the Operator Panel Message Display Understanding the Operator PanelMessage Meaning Paper Size Indicator Interface IndicatorMessage Paper Size Display Indicator Description Paper Type IndicatorREADY, DATA, and Attention Indicators Message Display Paper Type Keys Key Function Over operator panel settings Menu System Road Map TCP/IP IBM KIR A4/LT Off Printer Reset Resource Prot Permanent Perm / Temp Buzzer Print Menu Map Printing Test PagesMenu Map Print Menu Map ? Menu MAP Sample Menu MAP Print Status StatusPrint Status Page ? Status Software Version Installation OptionsError Log Hardware Information Interface Information KIR Test Pattern Service Service StatusOthers Network Card Interface Status Opt. StatusPage ? On Opt. StatusPage ? OffOpt. StatusPage On Font Select Internal Font ListsFont List Font Lists Prescribe Print HEX-DUMP? Received Data DumpingPrint HEX-DUMP Processing Waiting Setting the Paper Size in Paper Cassette Setting the Paper SizePaper Handling Paper Handling Custom Paper Size Cassette Size Custom Unit mm Unit ? mm Dimension Dimension 216 mmSetting the Paper Size in MP Tray MP Tray Size A4 MP Tray Size ? A4 Cassette Type Plain Setting the Paper TypeSetting the Paper Type in Paper Cassette Cassette Type ? Plain MP Tray Type Plain Setting the Paper Type in MP TrayMP Tray Type ? Plain Type Adjust Custom Creating Custom Paper Type Paper Handling Paper Weight ? Normal Paper Weight NormalSetting the Paper Weight Duplex path ? Enable Duplex path EnableSetting the Duplex Path Reset Type Adjust ? Reset Type AdjustResetting the Custom Paper Type MP Tray Mode MP Tray Mode Cassette Feed Select Cassette MP Tray Mode ? CassetteSelecting the Paper Feed Source Feed Select ? Cassette Stack Select Top tray FaceDn Selecting the Output StackStack Select Override A4/LT Off Overriding A4 and Letter Size DifferenceOverride A4/LT ? Off Emulation ?PCL PaginationEmulation Changing the Emulation Alt. Emulation ?PCL EmulationEmulation ?KPDL Auto Alternative Emulation for Kpdl Emulation Printing Kpdl Errors ?KPDL Print Kpdl Errs ? On Default fontFont ?I000 I000Letter Description Size Points Default Font SizeSize Courier Regular Changing Type for Courier/Letter Gothic Setting the Character Pitch for Courier/Letter Gothic Pitch Code Set Code SetCode Set ?IBM PC-8 Set Number of CopiesCopies 001 Orientation Portrait Printing OrientationOrientation ? Portrait KIR Kyocera Image Refinement Status KIR Checking Lines KIR Mode ? On KIR ModePrint Quality EcoPrint Mode ? Off EcoPrint Mode OffEcoprint Resolution Fast 1200 mode ResolutionResolution MPS Mode Quick Copy Proof and Hold Private Print Stored JobJob Retention MPS Printing Additional Copies using Quick CopyQuick Copy Job Storage Quick Copy ?Arlen Quick Copy HaroldQuick Copy ?Harold Arlen ?Report Deleting a Quick Copy Job Report DeleteProof and Hold Printing Remaining Copies of a Proof and Hold Job Quick Copy Private/Stored ?Harold Printing a Private JobPrivate/Stored Harold Private/Stored ?Arlen Agenda Copies 001 AgendaAgenda Copies Agenda Delete Printing a Stored Job Releasing a Stored Job Deleting a Stored Job Printing a Code Job KM-Net Job Manager MPS List of Code JOB Printing a List of Code JobsList of Code JOB ? Print VMB Data Tray001 Retrieving Jobs from Virtual Mailbox VMBTray001? List of VMB Printing a List of VMBList of VMB ? MPS Configuration MPS Configuration Temp. Code JOB Size 050MB Maximum Space Assigned to Temporary Code Jobs Size 05 0MB Perm. Code JOB Size 050MBMaximum Space Assigned to Permanent Code Jobs VMB Size VMB Size 050MBMaximum Space Assigned to Virtual Mailboxes Parallel Interface Mode Interface Parallel I/F ? Auto USB Interface ModeInterface ? USB Serial Interface Parameters Interface ? Serial Parity None Protocol DTRpos.&XON Baud Rate Data BitsStop Bits Baud Rate Network Interface Parameters EtherTalk Off Opt. StatusPage On NetWareTCP/IP ? On TCP/IP On Dhcp Off IP Address Subnet Mask Gateway 000.000.000.000 Operating the Storage Device RAM Disk Mode OffActivating the RAM Disk RAM Disk Mode ? On RAM Disk Size Mbyte Read Data Data name Reading DataMemory Card Read Data ?data name Write Data Writing DataWrite Data ? Write Information Delete Data data name Deleting DataDelete Data ?data name Read Fonts Reading Fonts from a CompactFlash CardRead Fonts ? Format Formatting a Storage DeviceFormat ? Printing a List of Data Names List of Partitions List Partitions ? Partition List Protect Mode ConfigurationProtect Linefeed LF Action Protect ? OnProtect ? Auto LF Action LF only CR Action CR only Carriage-Return CR ActionCR Action ? CR only Wide A4 Off Wide A4 PitchWide A4 ? Off Print Density Print Density Total Printed Pages Toner Counter ResettingNew Toner Installed Life Counters MSG Language English New Toner Installed ?Message Language MSG Language ? English Following order The key cycles in the reverse order Automatic Form Feed Timeout Form Feed Time Out 030sec Sleep Timer 015 min Sleep Timer SettingSleep Timer Sleep Mode ? Off Sleep ModeSleep Mode ? On Turning Off the Sleep Timer Printer Reset ? Printer ResettingPrinter Reset Self test Please wait Ready Resource Prot Off Resource ProtectionResource Prot ? Off Buzzer On Alarm Buzzer SettingBuzzer ? On Auto Continue Mode On Auto Continue SettingAuto Continue Mode ? On Setting the Auto Continue Recovery Time TimerAuto Continue Duplex Off Duplex Printing Error Detection SettingFinishing Error Duplex ? Off Paper Selection General Guidelines Paper SpecificationsSpecification Paper Availability Condition of the Paper Selecting the Right PaperComposition Smoothness Basis WeightPaper Size Multi-purpose Size Cassette or Tray Bond Weight lb Europe Metric Paper Weight Equivalence TableMoisture Content Weight g/m² Paper Grain Other Paper Properties Transparency Overhead Projection Film Special PaperPaper type Media type Adhesive-Backed Labels Postcards Envelopes Thick Paper Preprinted Paper Colored PaperRecycled Paper Paper Type Maintenance Toner Container Replacement Toner Container Replacement Interval Replenishing Toner Carefully remove the protective seal orange colored Push Here Waste Toner Box Replacement Replacing the Waste Toner Box Cap the waste toner box after removing from the printer Toner Counter Resetting on Cleaning Cleaning the Charger Wire Cleaning the Charger Grid Pull out the charger unit approximately 5 cm 2 inches Shown in the figure Cleaner is not re-usable Ramp using the wiper cloth included in the toner kit Paper Transfer Unit Troubleshooting Symptom Check Items Corrective Action General Guide Print Quality Problems Check the charger unit installation Check the Ecoprint settingCheck the print density Check the transfer roller Check the paper chute and the rampCheck the file or program Indicators Indicators and MessagesIndicator Name Condition Description Maintenance Messages Message Corrective Action Key. See Correcting a Paper Jam on Unnecessary fonts and macros. See Appendix a Error Messages See Operating the Storage Device on Beginning to ensure correct reading of the memory card From the operator panel, and re-select Auto Correcting a Paper Jam Paper jam Description Reference Message Location Jam recovery Jam at the Paper Cassette or Inside the Printer Shown in B Paper Jam at the Option Duplexer Pull out the duplex drawer Remove the jammed paper Paper Jam at the Option Sorter Close the rear cover of the option sorter Jam at the MP Tray Fonts List of Fonts PCL Scalable and Bitmap Fonts List of Fonts List of Fonts Kpdl Fonts Kpdl Fonts Appendix a Options Available Options 6Paper Feeder Expanding the Printer Memory YES no Removing the Main Circuit Board Circuit board, can cause serious damage to the printer Installing Dimm Dimm to be used Testing the Expansion Memory Removing Dimm Adjusting the Memory on the Printer Driver Installing Option Units PF-60 Paper Feeder Installing Option Units Load paper DU-61 Duplexer Gently place the printer on top of the duplexer Pass the connected cable and power cord through the opening SO-60 Sorter Cord, and printer cable Push the sorter down. The levers of the attachment legs are Grip Duplexer Rear Cover Do not move or lift the printer with the sorter installed Installing the envelope feeder on the printer EF-60 Envelope Feeder Load envelopes into the envelope feeder Pull out the sub-tray that matches the size of the envelopes Paper Setting Button Install the rear tray on the rear of the printer PT-4/PT-60 Rear Tray Network Interface Card About the modes, see Network Interface Parameters on Microdrive Hard Disk Return the main circuit board to the printer by reversing CompactFlash Memory Card Appendix B Host Computer Interface Parallel Interface Interface SignalsCommunication Reception Transmission Mode Parallel Interface Communication Modes Table B-2 Parallel Connector Pin Assignment Pin In/out Description Acknowledge* nAck Pin Specifications USB Interface Serial Interface Option Interface SignalsPin In/out Signal Description RS-232C Interface Table B-5 RS-232C ProtocolParameter value Baud rate Table B-7 Table B-6Parameter value Meaning Prescribe Frpo D0 Command Table B-8 RS-232C Cable Connection Connecting the Printer to the ComputerObtain a Suitable RS-232C Cable Double click on Communications Port RS-232C Cable Connection DOS, enter the following commands Appendix C Specifications Table C-1 Pressure level at the front Dimensions Power requirementsPower consumption Description Ambient conditions Glossary IEEE1284 Cassette modeFirst mode Dpi dots per inch Outline font Sleep modeOperator panel Parallel interface Index Index-2 Index-3 2003 Is a trademark of Kyocera Corporation