OPERATION | ||||
|
| USER DEFINED PARAMETERS |
|
|
|
|
|
|
|
|
|
|
|
|
| Parameter | Definition |
|
|
|
|
|
|
|
| P.7 | Gun Offset Adjustment |
|
|
|
| Range: |
|
|
|
| Adjusts the wire feed speed calibration of the pull motor of a |
| |
|
| performed when other possible corrections do not solve any |
| |
|
| rpm meter is required to perform the pull gun motor offset calibration. To perform the calibration |
| |
|
| procedure do the following: |
|
|
|
| • Release the pressure arm on both the pull and push wire drives. |
|
|
|
| • Set the wire feed speed to 200 ipm. |
|
|
|
| • Remove wire from the pull wire drive. |
|
|
|
| • Hold an rpm meter to the drive roll in the pull gun. |
|
|
|
| • Pull the trigger on the |
|
|
|
| • Measure the rpm of the pull motor. The rpm should be between 115 and 125 rpm. If neces- |
| |
|
| sary, decrease the calibration setting to slow the pull motor, or increase the calibration setting |
| |
|
| to speed up the motor. |
|
|
|
|
|
|
|
| P.8 | TIG Gas Control |
|
|
|
| Allows control over which gas solenoid actuates while TIG welding. |
|
|
|
| • Valve (manual) = No MIG solenoid will actuate while TIG welding, gas flow is manually con- |
| |
|
| trolled by an external valve. |
|
|
|
| • Feeder Solenoid = The internal (feeder) MIG solenoid will turn on and off automatically while |
| |
|
| TIG welding. |
|
|
|
| • Power source Solenoid = Any gas solenoid connected to the power source will turn on and off |
| |
|
| automatically while TIG welding. |
|
|
|
| Notes: |
|
|
|
| • Preflow is not available while TIG welding. |
|
|
|
| • Postflow is available - the same postflow time will be used in MIG and TIG. |
|
|
|
| • When machine output on/off is controlled via the upper right knob, gas flow will not start until |
| |
|
| the tungsten touches the work. Gas flow will continue when the arc is broken until the |
| |
|
| Postflow time expires. |
|
|
|
| • When machine output on/off is controlled via an arc start switch or foot Amptrol, gas will begin |
| |
|
| flowing when the output is turned on and will continue flowing until the output is turned off and |
| |
|
| the Postflow time expires. |
|
|
|
|
|
|
|
| P.9 | Crater Delay |
|
|
|
| Range: Off to 10.0 seconds (default = Off) |
|
|
|
| Used to skip the Crater sequence when making short tack welds. If the trigger is released |
| |
|
| before the timer expires, Crater will be bypassed and the weld will end. If the trigger is released |
| |
|
| after the timer expires, the Crater sequence will function normally (if enabled). |
|
|
|
|
|
|
|
| P.14 | Reset Consumable Weight |
|
|
|
| Only appears in the list with systems using Production Monitoring. Use this option to reset the |
| |
|
| initial weight of the consumable package. Press the right Mode Select Button to reset the con- |
| |
|
| sumable weight. |
|
|
|
|
|
|
|
|
|
|
|
|
