TROUbLESHOOTING | ||
|
|
|
Observe all Safety Guidelines detailed throughout this manual Error Codes for the Power Wave 455: Code 10555 and below
Note: For any Err # listed below write down the error number for refference and try cycling power to see if the error clears itself. If not, refer to what the What to Do column for the given Err.
| PRObLEMS |
| POSSIbLE |
|
| RECOMMENDED | ||||
| (SYMPTOMS) |
| CAUSE |
|
| COURSE OF ACTION | ||||
|
|
|
|
|
|
|
|
|
|
|
| Display shows any of the following: |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| |||
| Err 001 |
|
| More than 1 CB with the same |
|
| Make sure the group dip switch set- |
| ||
|
|
|
|
| group number. |
|
| ting is unique for each CB. |
| |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Err 003 |
|
| Too many objects in group. |
|
| A given group can only support up | |||
|
|
|
|
|
|
|
|
| to 7 objects. Remove any objects | |
|
|
|
|
|
|
|
|
| over 7 from the group either by | |
|
|
|
|
|
|
|
|
| changing the group dip switch set- | |
|
|
|
|
|
|
|
|
| tings or physically disconnecting any | |
|
|
|
|
|
|
|
|
| objects over 7 in the group. | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Err 004 |
| More than 1 object of the same |
|
| Adjust the dip switch setting to make | ||||
|
|
|
| eqipment type with the same group |
|
| either the group # or feed head # | |||
|
|
|
| # and feed head #. |
|
| unique for all oobjects of the same | |||
|
|
|
|
|
|
|
| equipment type. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
| Err 005 |
|
| A feed head has its feed head dip |
|
| The appropriate feed head # is 1 | |||
|
|
|
|
| switches set to zero in a group with |
|
| through 7. Check the dip switch set- | ||
|
|
|
|
| more than one object. |
|
| ting chart in INSTALLATION section | ||
|
|
|
|
|
|
|
|
| and set the switches to make the | |
|
|
|
|
|
|
|
|
| Feed head ID | |
|
|
|
| |||||||
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Err 006 | Did not receive a recognition com- | Check to see if the status light is not | |||||||
|
|
|
| mand from the power source. | solid green on the power source | |||||
|
|
|
|
|
|
|
| (refer to status light states in OPER- | ||
|
|
|
|
|
|
|
| ATION section if not). Also, check | ||
|
|
|
|
|
|
|
| continuity in the communication lines | ||
|
|
|
|
|
|
|
| from CB to Power Source (refer to | ||
|
|
|
|
|
|
|
| wiring diagram). Refer to Power | ||
|
|
|
|
|
|
|
| source trouble shooting section for | ||
|
|
|
|
|
|
|
| additional information. If all these | ||
|
|
|
|
|
|
|
| avenues fail, replace CB mother PC | ||
|
|
|
|
|
|
|
| board. | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
