Arclink System Error Codes | Lincoln Electric IM827-D manual

E-9	TROUbLESHOOTING	E-9

	Observe all Safety Guidelines detailed throughout this manual

PRObLEMS

(SYMPTOMS)

POSSIbLE

CAUSE

RECOMMENDED

COURSE OF ACTION

	ARCLINK SYSTEM ERROR CODES

Err 33	Capacitor bank "B" under	1. The power source input power
	voltage.		may be wired incorrectly. Verify
			the power source reconnect panel
			wiring matches the input power.
		2.	See the power source service
			Manual.

		1.	The power source input power
Err 34	Capacitor bank "A" overvolt-		may be wired incorrectly. Verify
	age.		the power source reconnect panel
			wiring matches the input power.
		2.	See the power source service
			Manual.

		1.	The power source input power
			may be wired incorrectly. Verify
Err 35	Capacitor bank "B" overvolt-		the power source reconnect panel
	age.		wiring matches the input power.
		2.	See the power source service		If all recommended possible areas of
			Manual.		misadjustment have been checked
					and the problem persists, Contact
					and the problem persists, Contact
		1.	The power source has exceeded		your local Lincoln Authorized
			the output current limits. Adjust		Field Service Facility.
			the welding procedure to reduce
Err 41	Long term secondary over-		the current draw. The welding
	current.		procedure may exceed the capac-
			ity of the power source.
		2.	See the power source service
			Manual.

		1.	Verify the power source reconnect
			panel wiring matches the input
			power.
Err 43	Capacitors are out of bal-
	ance	2.	See the power source service
			Manual.
		A high level of output current (long
		average ) has caused an overload.
					This happens when the wrong
Err 54	Short term secondary over-				Output stud is used on an STT
Err 54	Short term secondary over-				machine or if there is a missing input
	current.				machine or if there is a missing input
	current.				phase. When this fault occurs, the
					phase. When this fault occurs, the
					machine output will be shut off.

CAUTION

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

POWER FEED™ 10M SINGLE WIRE FEEDER

Image 65

Lincoln Electric IM827-D manual Arclink System Error Codes, Your local Lincoln Authorized, Field Service Facility

Contents

Safety Depends on You Power Feed 10M Wire Feeder California Proposition 65 Warnings Safety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosion Précautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage Immediately TAbLE of Contents TAbLE of Contents SPEC.# Type Input Power InstallationTemperature Rating Power Feed 10M Single Wire Feeder Electric Shock can kill Wire Drive Mounting See Figure A.1Location Mounting Weld CAbLE Connection Weld CAbLE SIzINGWeld CAbLE SIzES Electrode Lead Negative Electrode Polarity COAxIAL Weld CAbLES AVAILAbLE Control CAbLE Control CAbLE SpecificationsControl CAbLE Connections Description Changing Drive Rolls and Wire Guides Changing the GUN Receiver bUSHING Drive Roll Pressure SettingSet the drive roll pressure by To change the gun bushing Magnum GUN and CAbLE ASSEMbLIES Welding GUNS, Torches and ACCES- SoriesGUN Receiver bUSHING To change the gear ratio Wire Feed Shut Down CircuitChanging the Gear Ratio DIP Switch #8 Position Gear Ratio Wire Reel LoadingSpindle Placement Loading 16 to 44 lb .3 20kg Spools Figure A.10 Using K1504-1 Coil Reel Removing a Readi-Reel Weld Wire RoutingLoading 30 lb .6 kg Readi-Reels See Figure A.11 Shielding GAS Connection 13INSTALLATIONA-13 ExAMPLES of Connecting AN Arclink Power Wave System Wire Drive BOOM ConfigurationControl bOx CV Welding Pulse Welding or STT Welding Fumes and Gases can be dangerous OperationWelding Sparks can cause fire or explosion ARC Rays can burn Common Welding AbbREVIATIONS Definitions of Welding ModesProduct Description Recommended Processes Additional Required Equipment Required EquipmentProcess Limitations Equipment Limitations Front Panel Controls and Connections Status LED Synergic CV Voltage Display Volts / Trim Display and Output KNObPrior to Welding Overview Mode Select Panel 4 MSP4LAYOUT-CONTROLS see Figure b.3 LAYOUT-DIGITAL Display Changing Weld Modes POWER-UP SequenceChanging ARC Wave Control Infrared IR Control Accessing the Machine Setup Menu Limit SettingMachine SETUP/USER Preferences Figure b.3a Setup Menu SET-UP Features Menu User Defined Parameters Stall Factor Adjustment Parameter Definition Procedure Change Method Crater Delay Parameter Definition Gun Offset AdjustmentReset Consumable Weight TIG Gas Control Definition Push-Pull Gun Knob behavior Arc Start/Loss Error TimeDisplay Trim as Volts Option Sense From Studs 107 View Power Source Protocol 100 View DiagnosticsParameter Definition Show Test Modes 101 View Event Logs Step Trigger Operation Cold Feed / GAS Purge Switch Step / 4-STEP Trigger SwitchStep Trigger Sequence of Operation Step Trigger Operation Figure b.5 Modes Process Setup and OperationNon- Synergic ARC Control Steel and Stainless Synergic GMAW-P Pulsed MIG Welding Pulse-on-Pulse Welding CC Stick Modes Machine Functionality bY Weld Process Output Control KNObS, Weld Mode 5 Process Weld ModeCV GMAW/FCAW NON-SYNERGIC CV NON-SYNERGIC Modes Gmaw Synergic Wire SIzE 030 035 045 052Synergic CV Modes Material Process GAS Pulse and PULSE-0N-PULSE Modes Wire SIzEPulse and PULSE-ON-PULSE Synergic 035 045 052 STT and STT II SynergicSTT and STT II Modes Gtaw Touch Start TIG Welding Gtaw TIG WeldingTouch Start TIG All Metals Touch Start TIG User Memories DIP Switch Settings High Limit Limit SettingLow Limit Attribute Optional Accessories Accessories Lb. coils to 2 spindles Safety Precautions MaintenanceRoutine Maintenance CALIbRATION Specification 1TROUbLESHOOTINGE-1 Symptoms Cause Course of Action PRObLEMS POSSIbLERecommended Err No Heart beat response from See what to Do on Err Error Codes for the Power Wave TROUbLESHOOTING Other Symptoms Three Dashes PRObLEMSCause Recommended Course of Action Error Codes LINC-NET System Error Codes Your local Lincoln Authorized Arclink System Error CodesField Service Facility PRObLEMS POSSIbLE Output PRObLEMS TROUbLESHOOTING Recommended Feeder DiagramsPower Feed 10M Single Wire Diagrams 30.46 Dimension Print14.56 18.48 15.80 Precaucion Warnung