OPERATION |
| |||||
|
|
| USER DEFINED PARAMETERS |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Parameter | Definition |
|
|
|
|
| P.99 | Show Test Modes |
|
|
|
|
|
| Most power sources contain weld modes used for calibration and test purposes. By default, the machine |
|
| |
|
|
| does not include test weld modes in the list of weld modes that are available to the operator. To manually |
|
| |
|
|
| select a test weld mode, set this option to "Yes". When the power source is turned off and back on again, |
|
| |
|
|
| the test modes will no longer appear in the mode list. Test weld modes typically require the machine out- |
|
| |
|
|
| put to be connected to a grid load and cannot be used for welding. |
|
|
|
|
|
|
|
|
|
|
|
| P.100 | View Diagnostics |
|
|
|
|
|
| Diagnostics are only used for servicing or troubleshooting the Power Wave system. Select "Yes" to |
|
| |
|
|
| access the diagnostic options in the menu. Additional parameters will now appear in the setup menu |
|
| |
|
|
| (P.101, P.102, etc). |
|
|
|
|
|
|
|
|
|
|
|
| P.101 | View Event Logs |
|
|
|
|
|
| Used for viewing all the system event logs. Press the right MSP Button to enter the option. Rotate Set |
|
| |
|
|
| knob to select the desired system log to read. Press the right button again to enter the selected log. |
|
| |
|
|
| Rotating the Set knob will scroll through the event log, displaying the log index number, event code and |
|
| |
|
|
| some other data. Press the left button to back out to select another log. Press the left button again to exit |
|
| |
|
|
| this option. |
|
|
|
|
|
|
|
|
|
|
|
| P.102 | View Fatal Logs |
|
|
|
|
|
| Used for viewing all the system fatal logs. Press the right MSP Button to enter the option. Rotate Set knob |
|
| |
|
|
| to select the desired log to read. Press the right button again to enter that log. Rotating the Set knob will |
|
| |
|
|
| scroll through the log, displaying the log index number and fatal code. Press the left button to back out to |
|
| |
|
|
| select another log. Press the left button again to exit this option. |
|
|
|
|
|
|
|
|
|
|
|
| P.103 | View Software Version Information |
|
|
|
|
|
| Used for viewing the firmware versions for each board in the system. Press the right MSP |
|
| |
|
|
| Button to enter the option. Rotate Set knob to select the desired board to read. Press the right |
|
| |
|
|
| button again to read the firmware version. Press the left button to back out to select another |
|
| |
|
|
| board. Rotate the SET knob to select another board, or press the left button to exit this option. |
|
| |
|
|
|
|
|
|
|
|
| P.104 | View Hardware Version Information |
|
|
|
|
|
| Used for viewing the hardware version for each board in the system. Press the right MSP |
|
| |
|
|
| Button to enter the option. Rotate Set knob to select the desired board to read. Press the right |
|
| |
|
|
| button again to read the hardware version. Press the left button to back out to select another |
|
| |
|
|
| board. Press the left button again to exit this option. |
|
|
|
|
|
|
|
|
|
|
|
| P.105 | View Welding Software Information |
|
|
|
|
|
| Used for viewing the Weld Set in the Power Source. Press the right MSP Button to read the |
|
| |
|
|
| Weld Set version. Press the left button to back out and exit this option. |
|
|
|
|
|
|
|
|
|
|
|
| P.106 | View Ethernet IP Address |
|
|
|
|
|
| Used for viewing the Ethernet Network IP address if there is an Ethernet board present in the |
|
| |
|
|
| system. Press the right MSP Button to read the IP Address. Press the left button to back out |
|
| |
|
|
| and exit this option. The IP address cannot be changed using this option. |
|
|
|
|
|
|
|
|
|
|
|
| P.107 | View Power Source Protocol |
|
|
|
|
|
| Used for viewing the type of power source the feeder is connected to. Press the right MSP |
|
| |
|
|
| Button to identify the power source as either LincNet or ArcLink. Press the left button to back |
|
| |
|
|
| out and exit this option. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
