By 2 Format Point ID Alarm Report Codes | Linear DUAL 824 instruction

4 BY 2 FORMAT POINT ID REPORTING CODES

4 BY 2 FORMAT POINT ID ALARM REPORT CODES

✦Refer to the 4 by 2 Format Point ID Reporting Code table to view/edit the alarm reporting codes for each of the 24 sensors. The communicator will send these codes if Point ID is enabled

and any sensor triggers an alarm. The factory settings are listed, along with a blank area to write in the new installation values.

✦Use program Steps #210 - 233 to change the 4 by 2 Point ID alarm reporting codes.

✎NOTE: Be careful not to duplicate codes unless the Central Station requires speciﬁc codes for certain types of sensors.

PROGRAMMING

STEPS #210 - 233

ENTERS STEP NUMBER

0 - 99 FOR SENSOR ALARM CODE

STORES VALUE - 1 BING

STEPS #210-233

Any value from 0-99 can be programmed for each event using these steps (enter “0” to stop an event from reporting).

4 BY 2 FORMAT POINT ID TROUBLE REPORT CODES

✦Refer to the 4 by 2 Format Point ID Reporting Code table to view/edit the trouble reporting codes for each of the 24 sensors. The communicator will send these codes if Point ID is enabled and any sensor has a low battery or trouble condition. The factory settings are listed, along with a blank area to write in the new installation values.

✦Use program Steps #234 - 257 to change the 4 by 2 Point ID trouble reporting codes.

✎NOTE: Be careful not to duplicate codes unless the Central Station requires speciﬁc codes for certain types of sensors.

PROGRAMMING

STEPS #234 - 257

ENTERS STEP NUMBER

0 - 99 FOR SENSOR TROUBLE CODE

STORES VALUE - 1 BING

STEPS #234-257

Any value from 0-99 can be programmed for each event using these steps (enter “0” to stop an event from reporting).

44

Image 46

Linear DUAL 824 manual By 2 Format Point ID Alarm Report Codes, Steps #210-233, By 2 Format Point ID Trouble Report Codes

Contents

Supervised Wireless Security Control Panel Introduction Linear LLC Table of Contents Dual 824 Security System Control Panel DOOR/WINDOW Sensors Wireless KeypadRemote Controls Panic Buttons Security System Floor Plan Design the InstallationExample System Five system mode indicators Hardwired KeypadThree system supervisory indicators Overview of Keypads Hardwired Keypad Features Control Panel Features Terminals for hardwired loop inputs Wall Mounting Control Panel InstallationSystem Location External Antenna Hardwired Keypad Installation Hardwired Loop Wiring ARM/DISARM KEY Station Wiring External Alarm Siren Connection Telephone Line Connection Automation Output Connection Voice Response Module Control Panel Power Connection Backup Battery Installation Create the Master User Code Basic Control Panel ProgrammingGong and four beeps will sound Repeat Steps 3-6 to enable all of the hardwired loops used Program the Hardwired LoopsProgram the Wireless Sensors Programming Different Sensor Types For All Models Basic Sensor Installation DXS-10 Wireless Keypad DXS-31 & DXS-32 DOOR/WINDOW Sensors Test Sensors Customizing the Keypad Labeling the Sensor Locations Chime Mode OFF ModeSystem Operating Modes Home Instant Mode Home ModeLit sensor status indicators show which sensors are open Manual Bypassing of Sensors Away Mode Exit Delay For Leaving the Premises Sensor Operation in Each System Mode Test ModeSensor Function Table Wireless Sensor LOW Batteries Control Panel PowerPower indicator normally glows when AC power is on System Trouble Indications Gong and ﬁ ve Beeps will sound Customizing the SystemAdding Sensors to the System Removing Sensors from the System Making a Sensor Interior Making a Sensor a 24-HOUR Door ChimePress HOME, 8, then Away Press HOME, 7, then Away Programming Information Sensor Operation in Each System Mode Making a Sensor Perform a Different Function Advanced Programming Setup ModeControl Panel Programming Options Exit Delay Time Changing a Sensors Restore RequirementsEntry Delay Time Changing a Sensors Supervision Entry Delay Beeps Remote Control & Hardwire Arming LevelRemote Control & Hardwire Disarming Level Exit Delay Beeps Disabling Quick Arming Silent Burglary AlarmsSilent Emergency Alarms Automatic Restoral of Bypassed Sensors Automation Output on During and After Alarm Automation Output Mode During AlarmRemote Control & Hardwire ARM/DISARM Chirp Automation Output on During Alarm Automation Output While Armed Automation Output During EXIT/ENTRY DelaysRemote Access Password Automation Output Polarity Adding Additional User Codes Control Panel Master ResetRemoving Additional User Codes Communicator Programming General Communicator Options WAY Audio Communicator EnableWay manual, 3 2-way full duplex using this step Voice Response Call Limiter Dialing DelayDialing Method Reporting Format Call Routing Primary Telephone Number Telephone Number Delays and Special CharactersAccount Number Secondary Telephone Number Opening and Closing Reports Report Control Panel TroubleReport Force Arming Point ID Reporting General Reporting Codes Steps #201-206 Steps #261-266 System Reporting CodesFire and Emergency buttons and for each Force Arming Reporting Code By 2 Format Point ID Trouble Report Codes By 2 Format Point ID Alarm Report CodesSteps #210-233 Steps #234-257 By 2 Format Point ID Reporting Codes Important Information