SYSTEM REPORTING CODES |
|
| |
|
| ||
✦ Refer to the System Reporting Codes table to |
|
| |
view/edit the reporting codes for the keypad | PROGRAMMING |
| |
FIRE and EMERGENCY buttons and for each of | STEPS #261 - 266 |
| |
the three Control Panel conditions. The factory |
|
| |
settings are listed, along with a blank area to |
|
| |
write in the new installation values. | ENTERS STEP NUMBER |
| |
STEPS | 0 - 99 FOR SYSTEM |
| |
Any value from | REPORTING CODE |
| |
each event using these steps (enter “0” to stop | STORES VALUE - 1 BING |
| |
an event from reporting). |
| ||
|
| ||
|
|
|
|
FORCE ARMING REPORTING CODE |
|
|
|
|
|
| |
✦ The factory set reporting code for force arming is |
|
|
|
“65” (Code 574 with Ademco). |
| PROGRAMMING STEP #258 |
|
STEP #258 Any value from |
|
| |
|
|
| |
event using this step (0 = no report). |
|
|
|
✎ NOTE: For force arming reporting, force arming |
| ENTERS STEP NUMBER |
|
reports must be enabled. See Page 41. |
|
| |
|
| 0 - 99 FOR FORCE ARMING |
|
|
| REPORTING CODE |
|
|
| STORES VALUE - 1 BING |
|
|
|
|
|
|
|
|
|
DURESS REPORTING CODE
✦The factory set reporting code for Duress is “66” (Code 121 with Ademco).
STEP #259 Any value from
✎NOTE: For duress code reporting a keypad duress code must be programmed. See Page 34.
PROGRAMMING STEP #259
ENTERS STEP NUMBER
0 - 99 FOR DURESS CODE
STORES VALUE - 1 BING
SYSTEM REPORTING CODES
STEP # | PROGRAMMING FUNCTION | POSSIBLE | FACTORY | ADEMCO VALUE | INSTALLATION | ||||
4 BY 2 VALUES | 4 BY 2 VALUES | 4 BY 2 VALUE | |||||||
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| |
258 | FORCE ARMING REPORT CODE | 0 - 99 |
| 65 |
| 574 |
| ||
|
|
|
|
|
|
|
|
| |
259 | DURESS REPORT CODE | 0 - 99 |
| 66 |
| 121 |
| ||
|
|
|
|
|
|
|
|
| |
261 | SYSTEM FIRE REPORT CODE | 0 - 99 |
| 68 |
| 110 |
| ||
|
|
|
|
|
|
|
|
| |
262 | SYSTEM EMERGENCY REPORT CODE | 0 - 99 |
| 69 |
| 120 |
| ||
|
|
|
|
|
|
|
|
| |
263 | SYSTEM TEST/CANCEL REPORT CODE | 0 - 99 |
| 70 |
| 406 |
| ||
|
|
|
|
|
|
|
|
| |
264 | SYSTEM LOW BATTERY RESTORAL REPORT CODE | 0 - 99 |
| 71 |
| R302 |
| ||
|
|
|
|
|
|
|
|
| |
265 | SYSTEM LOW BATTERY CODE | 0 - 99 |
| 73 |
| E302 |
| ||
|
|
|
|
|
|
|
|
| |
|
|
| System Reporting Codes Table |
|
| ||||
|
|
|
|
|
|
|
| ||
|
|
| OPENING & CLOSING REPORTING CODES TABLE |
|
| ||||
| USER CODE |
| 4 x 2 CLOSING |
| 4 x 2 OPENING |
| ADEMCO CLOSING | ADEMCO OPENING | |
|
| (ARMING) CODE |
| (DISARMING) CODE |
| (ARMING) CODE | (DISARMING) CODE | ||
|
|
|
|
| |||||
|
|
|
|
|
|
|
| ||
MASTER USER CODE1 |
| 74 |
| 82 |
| R401 C000 | E401 C000 | ||
|
|
|
|
|
|
|
| ||
RESTRICTED USER CODE #1 |
| 75 |
| 83 |
| R401 C001 | E401 C001 | ||
|
|
|
|
|
|
|
| ||
RESTRICTED USER CODE #2 |
| 76 |
| 84 |
| R401 C002 | E401 C002 | ||
|
|
|
|
|
|
|
| ||
RESTRICTED USER CODE #3 |
| 77 |
| 85 |
| R401 C003 | E401 C003 | ||
|
|
|
|
|
|
|
| ||
RESTRICTED USER CODE #4 |
| 78 |
| 86 |
| R401 C004 | E401 C004 | ||
|
|
|
|
|
|
|
| ||
RESTRICTED USER CODE #5 |
| 79 |
| 87 |
| R401 C005 | E401 C005 | ||
|
|
|
|
|
|
| |||
PAGE ALERT USER CODE |
|
|
| (DIALS PAGE NUMBER ONLY, NO CODES REPORTED) |
| ||||
|
|
|
|
|
|
|
| ||
REMOTE/HARDWIRE ARM (SENSOR FCN. 9) & QUICK ARM |
| 81 |
|
|
| R407 C007 |
| ||
|
|
|
|
|
|
|
| ||
REMOTE/HARDWIRE DISARM (SENSOR FCN. 9) |
|
|
| 89 |
|
| E407 C007 | ||
|
|
|
|
|
|
|
|
| |
Opening & Closing Reporting Codes Table
43
