Mounting the Printer on a Wall | M-S Cash Drawer 7193 instruction

7193 Owner’s Guide

Setting Up the Printer

Mounting the Printer on a Wall

Use the wall-mount kit to mount the printer vertically on a wall. See “Ordering Paper and Supplies” in the chapter, “About the 7193 Printer,” for information on ordering the printer wall-mount kit.

The kit contains a mounting bracket, screws with plastic anchors, and a label. Once the printer is mounted on the wall, the operator panel will be upside down. The label corrects this so the panel can be easily read.

Select a wall that is accessible, but away from main traffic to keep the printer from being bumped or knocked off. Be sure there are no hidden wires or other obstructions in the wall where you mount the printer. Keep in mind the length of the cables when mounting the printer on the wall.

Be sure that the rubber pads have been attached to the bottom of the printer. See “Attaching the Feet” earlier in this chapter. The rubber pads help the printer to fit snugly against the mounting bracket.

You will need a 1/4 inch drill bit and either a Phillips or standard screwdriver (screws are combination Phillips and pan-slotted).

1.Using the bracket as a template, mark and drill a hole for each plastic anchor 1.25 inches deep.

2.Insert the anchors into the holes so they are flush with the wall surface and screw the bracket against the wall, tightening the screws so that the plastic anchors expand and hold firmly in the wall.

Do not overtighten the screws.

Note: Because the power cable and communication cable connect to the bottom of the printer, they must be connected before the printer can be attached to the bracket. If you haven't connected the cables to the printer, do so now. See “Connecting Communication and Power Cables” earlier in this chapter.

3.Line up the tabs of the bracket with the slots on the back of the printer and attach the printer to the bracket.

4.Place the label on the cover.

May 1996

Image 31

M-S Cash Drawer 7193 manual Mounting the Printer on a Wall

Contents

Owners Guide Information to User Quick Reference How to Obtain More Information How to Use This BookWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Options FeaturesModels Communication Interfaces Thermal Printhead Ordering Thermal Paper Ordering Paper and SuppliesRecommended Suppliers Kanzaki Specialty Papers Other Qualified Suppliers Ordering the Printer Wall-Mount Kit Ordering the Power Supply and CablesOrdering Cash Drawers Cleaning the Printer Removing the Packing Material What Is in the Box? Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables RS-232C Models Connecting Communication and Power Cables Parallel Models Turning On the Printer Loading and Changing Paper When to Change the Paper Removing the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Operator Panel Lights Solving Problems Service-Related Problems Correcting ProblemsOperator-Correctable Conditions No Power to Printer or Power Voltages Incorrect Contacting a Service RepresentativePrint is Light or Spotty Level 0 Diagnostics Diagnostics Eerom Level 1 Diagnostics Setting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Enter the Data Scope Mode Running the Data Scope Mode 1BH Exit the Data Scope Mode Testing Receipt Printing Level 3 Diagnostics Level 2 Diagnostics Communication Overview Sending CommandsInterfaces Using Basic to Send Commands Using DOS to Send CommandsRS-232C Interface DTR/DSR Protocol XON/XOFF Protocol Connectors RS-232C Technical Specifications Cash Drawer Connectors Switch Settings OFF Parallel Protocol Parallel Interface Parallel Connectors Parallel Technical Specifications Parallel Printers Parallel Switch Settings Command List Commands Printer Function Commands Owner’s Guide Print Characteristics Commands Printer Status Commands Graphics Commands Bar Code Commands Real Time Commands Horizontal Tab Command DescriptionsLine Feed Clear Printer Carriage ReturnFeed n Print Lines Add n Extra Dot Rows Feed n Dot RowsPrint Set Column Full Knife CutPartial Knife Cut Generate Tone Set Absolute Starting Position Set Character Right-Side Spacing Initialize Printer Set Line Spacing to 1/6 InchSet Line Spacing to n Minimum Units Select Printer Print and Feed n Minimum Units Set Horizontal Tab Positions Set Relative Starting Position Print and Feed n Lines Enable or Disable Panel SwitchAlign Character Positions Select Sensors to Stop Printing Generate Pulse to Open Cash Drawer Read from Non-Volatile MemoryWrite to Non-Volatile Memory Select Single-Wide Characters Select Double-Wide CharactersRotate Characters Counter-Clockwise Select Pitch Column Width Set Print Mode Define User-Defined Character Set Select Character Set Select Character Code Table Copy Character Set from ROM to RAM Set or Cancel Upside-Down Characters Set or Cancel Rotated Characters Clockwise Summary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Double-Density Graphics Single-Density Graphics Define Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Alternate Implementation Rules for Using Real Time Commands Moving Data Through the Buffer Busy Line and Fault Conditions GS Sequence Real Time Status Transmission = Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Receipt Paper Status Real Time Request to Printer DLE Sequence Real Time Printer Status Transmission Clear Printer Command Recognizing Data from the Printer Select Pitch of HRI Characters Select Printing Position of HRI CharactersSelect Height of Bar Code JAN8 EAN Print Bar Code Select Width of Bar Code Print Code 128 Bar Code Reliability Appendix a Specifications Environmental Conditions Power Requirements Printing Specifications Dimensions and Weight Print Zones Duty Cycle Restrictions Printing Solid Blocks Density of Receipt Print Lines Appendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May May Index Index 112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB