Define Downloaded Bit Image | M-S Cash Drawer 7193 manual

Commands

7193 Owner’s Guide

Define Downloaded Bit Image

Enters a downloaded bit image (such as a logo) into RAM with the number of dots specified by n1 and n2. It is available until power is turned off, another bit image is defined, or either Initialize Printer (1B 40), or Define User-Defined Character Set (1B 26), command is received.

A downloaded bit image and user-defined characters cannot be defined at the same time. Any user-defined characters will be cleared from RAM when this command is used. See the illustration on the next page for a representation of the bit image.

Hex	Decimal	ASCII
1D 2A n1 n2 d1 ... dn	29 42 n1 n2 d1 ... dn GS * n1 n2 d1 ... dn
Value of n1		Value of n2	Value of d
1-56 (8 x n1 = Number of		1-48 (Number of	Bytes of Data (Printed
Horizontal Dot Columns)		Vertical Bytes)1	Down, Then Across)

1The number of bytes sent is represented by the following formula: n = 8 x n1 x n2 (n1 x n2 must be less than or equal to 1344).

82

May 1996

Image 85

M-S Cash Drawer 7193 manual Define Downloaded Bit Image

Contents

Owners Guide Information to User Quick Reference How to Obtain More Information How to Use This BookWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Models FeaturesCommunication Interfaces Options Thermal Printhead Ordering Thermal Paper Ordering Paper and SuppliesRecommended Suppliers Kanzaki Specialty Papers Other Qualified Suppliers Ordering the Printer Wall-Mount Kit Ordering the Power Supply and CablesOrdering Cash Drawers Cleaning the Printer Removing the Packing Material What Is in the Box? Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables RS-232C Models Connecting Communication and Power Cables Parallel Models Turning On the Printer Loading and Changing Paper When to Change the Paper Removing the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Operator Panel Lights Solving Problems Service-Related Problems Correcting ProblemsOperator-Correctable Conditions No Power to Printer or Power Voltages Incorrect Contacting a Service RepresentativePrint is Light or Spotty Level 0 Diagnostics Diagnostics Eerom Level 1 Diagnostics Setting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Enter the Data Scope Mode Running the Data Scope Mode 1BH Exit the Data Scope Mode Testing Receipt Printing Level 3 Diagnostics Level 2 Diagnostics Communication Overview Sending CommandsInterfaces Using Basic to Send Commands Using DOS to Send CommandsRS-232C Interface DTR/DSR Protocol XON/XOFF Protocol Connectors RS-232C Technical Specifications Cash Drawer Connectors Switch Settings OFF Parallel Protocol Parallel Interface Parallel Connectors Parallel Technical Specifications Parallel Printers Parallel Switch Settings Command List Commands Printer Function Commands Owner’s Guide Print Characteristics Commands Printer Status Commands Graphics Commands Bar Code Commands Real Time Commands Horizontal Tab Command DescriptionsLine Feed Clear Printer Carriage ReturnFeed n Print Lines Add n Extra Dot Rows Feed n Dot RowsPrint Partial Knife Cut Full Knife CutGenerate Tone Set Column Set Absolute Starting Position Set Character Right-Side Spacing Set Line Spacing to n Minimum Units Set Line Spacing to 1/6 InchSelect Printer Initialize Printer Print and Feed n Minimum Units Set Horizontal Tab Positions Set Relative Starting Position Align Character Positions Enable or Disable Panel SwitchSelect Sensors to Stop Printing Print and Feed n Lines Generate Pulse to Open Cash Drawer Read from Non-Volatile MemoryWrite to Non-Volatile Memory Select Single-Wide Characters Select Double-Wide CharactersRotate Characters Counter-Clockwise Select Pitch Column Width Set Print Mode Define User-Defined Character Set Select Character Set Select Character Code Table Copy Character Set from ROM to RAM Set or Cancel Upside-Down Characters Set or Cancel Rotated Characters Clockwise Summary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Double-Density Graphics Single-Density Graphics Define Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Alternate Implementation Rules for Using Real Time Commands Moving Data Through the Buffer Busy Line and Fault Conditions GS Sequence Real Time Status Transmission = Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Receipt Paper Status Real Time Request to Printer DLE Sequence Real Time Printer Status Transmission Clear Printer Command Recognizing Data from the Printer Select Pitch of HRI Characters Select Printing Position of HRI CharactersSelect Height of Bar Code JAN8 EAN Print Bar Code Select Width of Bar Code Print Code 128 Bar Code Reliability Appendix a Specifications Environmental Conditions Power Requirements Printing Specifications Dimensions and Weight Print Zones Duty Cycle Restrictions Printing Solid Blocks Density of Receipt Print Lines Appendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May May Index Index 112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB