Setting Partial Cut Distance | M-S Cash Drawer 7193 specs

Diagnostics

7193 Owner’s Guide

Setting Partial Cut Distance

This function allows you to change the length of the partial knife cut: the higher the number, the longer the cut.

Caution: The DIP switches are set at the factory to predetermined settings and should generally not be changed. If you must change the settings, do so carefully to avoid changing other functions. Run the print test to see what the current selection is for this function. See “Testing The Printer” On Page 23.

1.Turn the power off.

2.Turn the printer over and note what the current DIP switch settings are.

3.Set the switches to the settings in the table that match the cut distance value you want (the higher the number, the longer the cut ).

Switch 1	Switch 2	Switch 3	Switch 4	Switch 5	Switch 6 Cut Distance Value
On	On	Off	Off	Off	Off	0
On	On	Off	Off	Off	On	1
On	On	Off	Off	On	Off	2
On	On	Off	Off	On	On	3
On	On	Off	On	Off	Off	4
On	On	Off	On	Off	On	5 (Default)
On	On	Off	On	On	Off	6

On	On	Off	On	On	On	7

4.Turn the power back on to enter the settings into the EEROM. The On Line light (green) blinks.

5.Turn the power off.

6.Set the DIP switches to the former settings.

DIP switch 1 must be Off to return the printer to the on-line mode.

38

May 1996

Image 43

M-S Cash Drawer 7193 manual Setting Partial Cut Distance

Contents

Owners Guide Information to User Quick Reference How to Obtain More Information How to Use This BookWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Options FeaturesModels Communication Interfaces Thermal Printhead Ordering Thermal Paper Ordering Paper and SuppliesRecommended Suppliers Kanzaki Specialty Papers Other Qualified Suppliers Ordering the Printer Wall-Mount Kit Ordering the Power Supply and CablesOrdering Cash Drawers Cleaning the Printer Removing the Packing Material What Is in the Box? Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables RS-232C Models Connecting Communication and Power Cables Parallel Models Turning On the Printer Loading and Changing Paper When to Change the Paper Removing the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Operator Panel Lights Solving Problems Service-Related Problems Correcting ProblemsOperator-Correctable Conditions No Power to Printer or Power Voltages Incorrect Contacting a Service RepresentativePrint is Light or Spotty Level 0 Diagnostics Diagnostics Eerom Level 1 Diagnostics Setting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Enter the Data Scope Mode Running the Data Scope Mode 1BH Exit the Data Scope Mode Testing Receipt Printing Level 3 Diagnostics Level 2 Diagnostics Communication Overview Sending CommandsInterfaces Using Basic to Send Commands Using DOS to Send CommandsRS-232C Interface DTR/DSR Protocol XON/XOFF Protocol Connectors RS-232C Technical Specifications Cash Drawer Connectors Switch Settings OFF Parallel Protocol Parallel Interface Parallel Connectors Parallel Technical Specifications Parallel Printers Parallel Switch Settings Command List Commands Printer Function Commands Owner’s Guide Print Characteristics Commands Printer Status Commands Graphics Commands Bar Code Commands Real Time Commands Horizontal Tab Command DescriptionsLine Feed Clear Printer Carriage ReturnFeed n Print Lines Add n Extra Dot Rows Feed n Dot RowsPrint Set Column Full Knife CutPartial Knife Cut Generate Tone Set Absolute Starting Position Set Character Right-Side Spacing Initialize Printer Set Line Spacing to 1/6 InchSet Line Spacing to n Minimum Units Select Printer Print and Feed n Minimum Units Set Horizontal Tab Positions Set Relative Starting Position Print and Feed n Lines Enable or Disable Panel SwitchAlign Character Positions Select Sensors to Stop Printing Generate Pulse to Open Cash Drawer Read from Non-Volatile MemoryWrite to Non-Volatile Memory Select Single-Wide Characters Select Double-Wide CharactersRotate Characters Counter-Clockwise Select Pitch Column Width Set Print Mode Define User-Defined Character Set Select Character Set Select Character Code Table Copy Character Set from ROM to RAM Set or Cancel Upside-Down Characters Set or Cancel Rotated Characters Clockwise Summary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Double-Density Graphics Single-Density Graphics Define Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Alternate Implementation Rules for Using Real Time Commands Moving Data Through the Buffer Busy Line and Fault Conditions GS Sequence Real Time Status Transmission = Transmit Printer Status = Transmit RS-232C Busy Status = Transmit Receipt Paper Status Real Time Request to Printer DLE Sequence Real Time Printer Status Transmission Clear Printer Command Recognizing Data from the Printer Select Pitch of HRI Characters Select Printing Position of HRI CharactersSelect Height of Bar Code JAN8 EAN Print Bar Code Select Width of Bar Code Print Code 128 Bar Code Reliability Appendix a Specifications Environmental Conditions Power Requirements Printing Specifications Dimensions and Weight Print Zones Duty Cycle Restrictions Printing Solid Blocks Density of Receipt Print Lines Appendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May May Index Index 112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB