Set Horizontal Tab Positions | M-S Cash Drawer 7193 specification

7193 Owner’s Guide

Commands

Set Horizontal Tab Positions

Sets up to 32 horizontal tab positions in ascending order n columns from column one, but does not move the print position. See the Horizontal Tab (09) command. The command ends with Hex 00; Hex 1B 44 00 clears all tabs. The tabs cannot be set higher than the column width of the current pitch: standard pitch = 44 columns; compressed pitch = 56 columns.

Hex	Decimal	ASCII	Value of n	Default
1B 44 n1 ...	27 68 n1 ...	ESC D n1 ...	Column for Tab	Every 8 chars. from
n32 00	n32 00	n32 00	Minus 1	col. 1 (9, 17, 25, etc.)

Print and Feed n Minimum Units

Prints one line from the buffer and feeds the paper n/360 inch. The line height equals the character height when n is too small.

Hex	Decimal	ASCII	Value of n
1B 4A n	27 74 n	ESC J n	0-255

May 1996

Image 72

M-S Cash Drawer 7193 manual Set Horizontal Tab Positions, Print and Feed n Minimum Units

Contents

Owners Guide Information to User Quick Reference How to Use This Book How to Obtain More InformationWho Should Use this Book? Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Features ModelsCommunication Interfaces Options Thermal Printhead Ordering Paper and Supplies Ordering Thermal PaperRecommended Suppliers Other Qualified Suppliers Kanzaki Specialty Papers Ordering the Power Supply and Cables Ordering the Printer Wall-Mount KitOrdering Cash Drawers Cleaning the Printer What Is in the Box? Removing the Packing Material Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables Connecting Communication and Power Cables RS-232C Models Parallel Models Turning On the Printer When to Change the Paper Loading and Changing Paper Removing the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Solving Problems Operator Panel Lights Correcting Problems Service-Related ProblemsOperator-Correctable Conditions Contacting a Service Representative No Power to Printer or Power Voltages IncorrectPrint is Light or Spotty Diagnostics Level 0 Diagnostics Level 1 Diagnostics Eerom Setting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Running the Data Scope Mode Enter the Data Scope Mode Exit the Data Scope Mode 1BH Testing Receipt Printing Level 2 Diagnostics Level 3 Diagnostics Sending Commands Communication OverviewInterfaces Using DOS to Send Commands Using Basic to Send CommandsRS-232C Interface XON/XOFF Protocol DTR/DSR Protocol RS-232C Technical Specifications Connectors Cash Drawer Connectors Switch Settings OFF Parallel Interface Parallel Protocol Parallel Technical Specifications Parallel Connectors Parallel Printers Parallel Switch Settings Commands Command List Printer Function Commands Owner’s Guide Print Characteristics Commands Graphics Commands Printer Status Commands Real Time Commands Bar Code Commands Command Descriptions Horizontal TabLine Feed Carriage Return Clear PrinterFeed n Print Lines Feed n Dot Rows Add n Extra Dot RowsPrint Full Knife Cut Partial Knife CutGenerate Tone Set Column Set Character Right-Side Spacing Set Absolute Starting Position Set Line Spacing to 1/6 Inch Set Line Spacing to n Minimum UnitsSelect Printer Initialize Printer Set Horizontal Tab Positions Print and Feed n Minimum Units Set Relative Starting Position Enable or Disable Panel Switch Align Character PositionsSelect Sensors to Stop Printing Print and Feed n Lines Read from Non-Volatile Memory Generate Pulse to Open Cash DrawerWrite to Non-Volatile Memory Select Double-Wide Characters Select Single-Wide CharactersRotate Characters Counter-Clockwise Set Print Mode Select Pitch Column Width Select Character Set Define User-Defined Character Set Copy Character Set from ROM to RAM Select Character Code Table Set or Cancel Rotated Characters Clockwise Set or Cancel Upside-Down Characters Summary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Single-Density Graphics Double-Density Graphics Define Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Rules for Using Real Time Commands Alternate Implementation Moving Data Through the Buffer Busy Line and Fault Conditions Real Time Status Transmission GS Sequence = Transmit Printer Status = Transmit RS-232C Busy Status Real Time Request to Printer = Transmit Receipt Paper Status DLE Sequence Clear Printer Command Real Time Printer Status Transmission Recognizing Data from the Printer Select Printing Position of HRI Characters Select Pitch of HRI CharactersSelect Height of Bar Code Print Bar Code JAN8 EAN Print Code 128 Bar Code Select Width of Bar Code Appendix a Specifications Reliability Power Requirements Environmental Conditions Dimensions and Weight Printing Specifications Print Zones Density of Receipt Print Lines Duty Cycle Restrictions Printing Solid Blocks Appendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May Index May Index 112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB