Parallel Interface, Parallel Protocol | M-S Cash Drawer 7193

Communication

7193 Owner’s Guide

Parallel Interface

Parallel Protocol

The 7193 uses a standard PC-compatible parallel interface. The following illustration shows the timing diagram for the interface protocol.

1.ACK/ will not go high until STROBE/ goes high.

2.When the printer is not ready to receive more data, ACK/ will be sent, but BUSY will remain high.

3.When the power is turned on or the printer is reset, an ACK/ will be sent during initialization.

4.Typical time from STROBE/ to ACK/ is approximately 44 µ seconds.

52

May 1996

Image 56

M-S Cash Drawer 7193 manual Parallel Interface, Parallel Protocol

Contents

Owners Guide Information to User Quick Reference Who Should Use this Book? How to Use This BookHow to Obtain More Information Contents Solving Problems Appendix B Print Characteristics 107 About the 7193 Printer Features ModelsCommunication Interfaces Options Thermal Printhead Recommended Suppliers Ordering Paper and SuppliesOrdering Thermal Paper Other Qualified Suppliers Kanzaki Specialty Papers Ordering Cash Drawers Ordering the Power Supply and CablesOrdering the Printer Wall-Mount Kit Cleaning the Printer What Is in the Box? Removing the Packing Material Repacking the Printer Choosing a Location Setting Switches Owner’s Guide Attaching the Feet Connecting Cash Drawer Cables Connecting Communication and Power Cables RS-232C Models Parallel Models Turning On the Printer When to Change the Paper Loading and Changing Paper Removing the Paper Roll Putting In the Paper Roll Advancing Paper Testing the Printer 3cx39pi Mounting the Printer on a Wall Bracket Mounting the Power Supply on a Wall Holder Solving Problems Operator Panel Lights Operator-Correctable Conditions Correcting ProblemsService-Related Problems Print is Light or Spotty Contacting a Service RepresentativeNo Power to Printer or Power Voltages Incorrect Diagnostics Level 0 Diagnostics Level 1 Diagnostics Eerom Setting Data Error and Data Buffer options Setting Printhead Resistance Setting Default Lines per Inch Setting Partial Cut Distance Ignoring/Using the Carriage Return Running the Data Scope Mode Enter the Data Scope Mode Exit the Data Scope Mode 1BH Testing Receipt Printing Level 2 Diagnostics Level 3 Diagnostics Interfaces Sending CommandsCommunication Overview RS-232C Interface Using DOS to Send CommandsUsing Basic to Send Commands XON/XOFF Protocol DTR/DSR Protocol RS-232C Technical Specifications Connectors Cash Drawer Connectors Switch Settings OFF Parallel Interface Parallel Protocol Parallel Technical Specifications Parallel Connectors Parallel Printers Parallel Switch Settings Commands Command List Printer Function Commands Owner’s Guide Print Characteristics Commands Graphics Commands Printer Status Commands Real Time Commands Bar Code Commands Line Feed Command DescriptionsHorizontal Tab Feed n Print Lines Carriage ReturnClear Printer Print Feed n Dot RowsAdd n Extra Dot Rows Full Knife Cut Partial Knife CutGenerate Tone Set Column Set Character Right-Side Spacing Set Absolute Starting Position Set Line Spacing to 1/6 Inch Set Line Spacing to n Minimum UnitsSelect Printer Initialize Printer Set Horizontal Tab Positions Print and Feed n Minimum Units Set Relative Starting Position Enable or Disable Panel Switch Align Character PositionsSelect Sensors to Stop Printing Print and Feed n Lines Write to Non-Volatile Memory Read from Non-Volatile MemoryGenerate Pulse to Open Cash Drawer Rotate Characters Counter-Clockwise Select Double-Wide CharactersSelect Single-Wide Characters Set Print Mode Select Pitch Column Width Select Character Set Define User-Defined Character Set Copy Character Set from ROM to RAM Select Character Code Table Set or Cancel Rotated Characters Clockwise Set or Cancel Upside-Down Characters Summary of Rotated Printing Set Bit Image Mode N1 + 256 x n2 N1 + 256 x n2 Number of Bytes of Data Single-Density Graphics Double-Density Graphics Define Downloaded Bit Image Print Downloaded Bit Image Transmit Cash Drawer Status Request Alternate Status Transmit Printer Status First Implementation Rules for Using Real Time Commands Alternate Implementation Moving Data Through the Buffer Busy Line and Fault Conditions Real Time Status Transmission GS Sequence = Transmit Printer Status = Transmit RS-232C Busy Status Real Time Request to Printer = Transmit Receipt Paper Status DLE Sequence Clear Printer Command Real Time Printer Status Transmission Recognizing Data from the Printer Select Height of Bar Code Select Printing Position of HRI CharactersSelect Pitch of HRI Characters Print Bar Code JAN8 EAN Print Code 128 Bar Code Select Width of Bar Code Appendix a Specifications Reliability Power Requirements Environmental Conditions Dimensions and Weight Printing Specifications Print Zones Density of Receipt Print Lines Duty Cycle Restrictions Printing Solid Blocks Appendix B Print Characteristics Appendix B Print Characteristics Owner’s Guide 110 May Index May Index 112 Owner’s Guide Owner’s Guide 114 Owner’s Guide Owner’s Guide Axiohm IPB