TCP/IP Communication Software | Maxtor NVR-2028 specs

9.2 TCP/IP Communication Software

Follow the instructions below to install the TCP/IP communication program into your computer. Click the Start Menu from your computer, and point to the Settings/Control panel.

Click the NETWORK icon twice to enter the NETWORK setting windows.

Click on the Configuration tag; check if the TCP/IC is included among the network components list. If the TCP/IP is included, please process step 5. If it is not included, please follow step 4 to install the TCP/IP.

61

Image 63

Maxtor NVR-2028 manual TCP/IP Communication Software

Contents

Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesPage Front View Hard-disk drive compartmentHard disk compartment lock Up / Down CH4-CH8 /CH3-CH7 buttons Setup/Save buttonRec Indicator Left / Right CH1-CH5 /CH2-CH6 buttons Shuttle Ring Disk IndicatorPower Indicator Mobile Rack Power LED Rear View Alarm In/Out This Figure is Looked from the Rear ViewNo Connection Basic Connection Use a RS-232 cable to install a wireless setting in a Lancam 192 Wireless Network Structure of the NVR and Its LANCAMs Hard-Disk Drive Installation SeagateMaxtor System Information Updating System Software Configuring Recording Settings 352 X Audio OFF720 X Audio OFF Timer Recording Recording OperationsManual Recording Start END 0000-0000 M 0000-0000 W 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-00000000-0000 Alarm Recording MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams below REC → 〔STOP 〕 → Operation Status From REC mode to Playback modePlayback Operations Fast Forward/Reverse Slow Forward/Reverse Play Back Picture-by-picturePlay Back Recorded Video from a HDD of the mobile rack Full List Search Alarm list SearchSearch Full List Alarm List Time Search Thumbnail SD Card Search Operations Time Search Thumbnail SearchDD MM Year HH MM 24 / 12 / 2003 00 2003 Alarm List Time Search Channel ： Thumbnail SD CardSD Card Search Search Thumbnail Year Full List Alarm Select Main Backup ALL Backup OperationsMobile Rack HD Backup Operations Backup Backup Main EXT Disk SET to Backup 1220 2001-02-01 0330 2001-03-02 0420 1330 Alarm Select Main Backup AlarmDisk Setting Reformat HD2 Usage Search button Save to F0000.JPG Save to F0001.JPG Save to F000N.JPG Secure Digital Card SD Card Backup Operations Key Lock Operation Menu Setup Title Login Name Quality Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingResolution Setting CH1 CH2 CH3 CH4 Image Setting Quality Highest Medium LOW Lowest SET Lancam Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion Bandwidth REC Setting REC Schedule Timer Enable on 1200-18000600-1800 0000-0000 MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm Setting Operation Main Wireless SettingWireless Setting Operation SET Privacy Lancam Setup RS232 WEP KEY SET Wireless SET WEP Encryption Mechanism KEYWEP KEY 1 … WEP KEY Main SET Network Comm SET Lancam Wireless Setting 2001 168 Main SET Network StatusPublic Private Protocol Port 2000 205 TCP Gateway XXX.YYY.ZZZ.TTT………………..NAT local IP Disables itEnables it Main SET IP Pool Range IP Pool Range Setting RS-232 HD Backup Full Main Disk REFORMAT/CLEAR HD BackupREC On Powers up the device System Setting Situation MAC 00 0c 0c 00 00 Bios Date Dec 24 Built-in hard disk Jumper settings of hard-disk drives for the system Location Mobile Rack Page Page D Message Meanings Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 System Main Goto Comm SET Ethernet Dhcp Configure Your NVR-2028 Network SettingsEnable Dhcp Function Set IP AddressPage TCP/IP Communication Software TCP/IP installation TCP/IP Configuration settingClick Start Settings Control Panel Network Click Start Programs MS-DOS Prompt Connection TestingPage Wire Wireless Network ViewerIntroduction to Network Viewer PIN Assignment RJ-45 PIN configuration for EthernetInstall the Network Viewer for the ZIP file PIN no View the NVR video from a remote PC Click to leave the Device Setup window ExitViewing images View the connected device Play List Function Buttons DescriptionPage Change the PC System Setting Set the System SetupSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the regular record settings Set the Alarm record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Connecting the NVR Description of functional keysBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Wireless NVR-2028 Design and specifications subject to change without noticeModel Number Appendix 1. -SCANIP Page Page Setup General Command FormatCommunication Protocol Command Types Command Main Category=0x02 Handshake Second Category=0x01Value of a specific front panel key Statedhcpwait Statesearch Statebackup