Installation Operating Manual | Maxtor NVR-2028 instruction

INSTALLATION &

OPERATINGMANUAL

Wireless Network Video Recorder

NVR-2028

Before trying to connect or operate this product, please read this manual completely

Image 1

Maxtor NVR-2028 manual Installation Operating Manual

Contents

Installation Operating Manual Page Safety Precautions Table Of Contents IDE Hard Disk Installation Product Introduction Product FeaturesPage Hard-disk drive compartment Front ViewHard disk compartment lock Rec Indicator Setup/Save buttonLeft / Right CH1-CH5 /CH2-CH6 buttons Up / Down CH4-CH8 /CH3-CH7 buttons Power Indicator Disk IndicatorMobile Rack Power LED Shuttle Ring Rear View This Figure is Looked from the Rear View Alarm In/OutNo Connection Basic Connection Use a RS-232 cable to install a wireless setting in a Lancam 192 Wireless Network Structure of the NVR and Its LANCAMs Seagate Hard-Disk Drive InstallationMaxtor System Information Updating System Software 352 X Audio OFF Configuring Recording Settings720 X Audio OFF Recording Operations Timer RecordingManual Recording Start END 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 0000-0000 M 0000-0000 W0000-0000 MAX REC Rate Unlimit PRE- Alarm OFF Main Alarm REC Enable Alarm Recording30 SEC Motion Detection Sensitivity Highest Region 30, 25 90 Externally triggered Recording Diagrams below Playback Operations Operation Status From REC mode to Playback modeFast Forward/Reverse REC → 〔STOP 〕 → Play Back Picture-by-picture Slow Forward/ReversePlay Back Recorded Video from a HDD of the mobile rack Search Full List Alarm List Time Search Thumbnail SD Card Alarm list SearchSearch Operations Full List Search Thumbnail Search Time SearchDD MM Year HH MM 24 / 12 / 2003 00 SD Card Search Alarm List Time Search Channel ： Thumbnail SD CardSearch Thumbnail Year Full List 2003 Mobile Rack HD Backup Operations Backup OperationsBackup Backup Main EXT Disk SET to Backup Alarm Select Main Backup ALL Disk Setting Reformat HD2 Usage Alarm Select Main Backup AlarmSearch button 1220 2001-02-01 0330 2001-03-02 0420 1330 Save to F0000.JPG Save to F0001.JPG Save to F000N.JPG Secure Digital Card SD Card Backup Operations Key Lock Operation Menu Setup Title Login Name Resolution Setting CH1 CH2 CH3 CH4 Quality Highest Lancam SET Image Resolution Image SettingImage Setting Quality Highest Medium LOW Lowest SET Lancam Quality Setting CH1 CH2 CH3 CH4 Image SET Audio ON/OFF Individually Sensitivity Highest Region 30, 25 90 Motion Bandwidth REC Setting 1200-1800 REC Schedule Timer Enable on0600-1800 0000-0000 MAX REC Rate Unlimit PRE- Alarm Main Alarm REC Enable Alarm Setting Wireless Setting Operation SET Privacy Lancam Setup Main Wireless SettingRS232 Operation KEY WEP KEY SET Wireless SET WEP Encryption MechanismWEP KEY 1 … WEP KEY Main SET Network Comm SET Lancam Wireless Setting Public Private Protocol Port 2000 205 Main SET Network StatusTCP 2001 168 Enables it Disables itMain SET IP Pool Range IP Pool Range Setting Gateway XXX.YYY.ZZZ.TTT………………..NAT local IP RS-232 HD Backup HD Backup Full Main Disk REFORMAT/CLEARREC On Powers up the device System Setting Situation MAC 00 0c 0c 00 00 Bios Date Dec 24 Built-in hard disk Jumper settings of hard-disk drives for the system Location Mobile Rack Page Page D Message Meanings Point stops recording Previously recorded data remaining 12-02-02 01-30-03 Lists 2999 02-03-03 3000 02-08-03 Enable Dhcp Function Configure Your NVR-2028 Network SettingsSet IP Address System Main Goto Comm SET Ethernet DhcpPage TCP/IP Communication Software TCP/IP Configuration setting TCP/IP installationClick Start Settings Control Panel Network Click Start Programs MS-DOS Prompt Connection TestingPage Network Viewer Wire WirelessIntroduction to Network Viewer Install the Network Viewer for the ZIP file RJ-45 PIN configuration for EthernetPIN no PIN Assignment View the NVR video from a remote PC Exit Click to leave the Device Setup windowViewing images View the connected device Play List Function Buttons DescriptionPage Set the System Setup Change the PC System SettingSet the Alarm Setup Change the Record & Timer Properties Via the Network Set the Alarm record settings Set the regular record settingsSet the Record Schedule Archive Images to the Computer Image Viewer Description of functional keys Connecting the NVRBrowsing images from the NVR Function Buttons Description Page Change Lancam Setup Setting Change Record / Alarm Setting Change Schedule Setting Change Wireless Setting Design and specifications subject to change without notice Wireless NVR-2028Model Number Appendix 1. -SCANIP Page Page General Command Format SetupCommunication Protocol Command Main Category=0x02 Handshake Second Category=0x01 Command TypesValue of a specific front panel key Statedhcpwait Statesearch Statebackup