Various recording settings (continued)
♦Motion threshold setting
In this step, the MOTION THRESHOLD setting, which serves as the trigger to initiate Alarm Recording, is set. In this setting, the minimum number of active dots required to initiate the MOTION DETECTION is established. The dots are activated in the MOTION DETECTION function set- tings. Using this value, the unit begins the MOTION DE- TECTION when motion has been detected in more than the specified minimum number of dots.
When establishing a value for the MOTION THRESHOLD setting, use a value which does not
exceed the number of active dots set for the MO- TION DETECTION function. Please note that the
MOTION DETECTION function will not operate if a larger value is used.
Example: Setting the MOTION THRESHOLD to “5” (the default setting is “2”).
1.After step 3 of
•The
<MOTION> |
| |
SELECTION CAMERA NO. 5 | ||
ON | ||
CH.MOTION DETECTION | ||
SET DETECTION MASK | HIGH |
|
SENSITIVITY | ||
@MOTION THRESHOLD | 2 | |
TEST MODE | OFF |
|
2.Turn the JOG dial to display 5 then turn the SHUTTLE ring to the right.
•The
<MOTION>
SELECTION CAMERA NO. 5
ON | |
CH.MOTION DETECTION | |
SET DETECTION MASK | HIGH |
SENSITIVITY | |
@MOTION THRESHOLD | 5 |
TEST MODE | OFF |
♦Test mode setting
Testing MOTION DETECTION setting.
Example: Setting the TEST MODE to “ON” (the default set- ting is “OFF”).
To set the TEST MODE, please turn ON the CH.
MOTION DETECTION.
1.After step 3 of
•The
<MOTION> |
| |
SELECTION CAMERA NO. 5 | ||
ON | ||
CH.MOTION DETECTION | ||
SET DETECTION MASK | HIGH |
|
SENSITIVITY | ||
MOTION THRESHOLD | 5 | |
@TEST MODE | OFF |
|
2.Turn the JOG dial to display ON then turn the SHUTTLE ring to the right.
•The <TEST MODE> menu will appear.
The area where the MOTION DETECTION func- tion has been activated is displayed using “ • ”. When
motion is detected on more dots than specified in the MOTION THRESHOLD setting, i.e., when Alarm Recording is initiated, the active symbol “ 
” will appear
3. To finish setting, turn the SHUTTLE ring to the left.
When motion is continuously detected within the active area established for the MOTION DETEC-
TION function, Alarm Recording will also continue. In this case, each Alarm Recording will be extended the duration that selecting
MOTION DETECTION HOLD FUNCTION When Alarm Recording continues as a result of motion being continuously detected, the unit cannot receive instructions for other functions. In this situa- tion, the MOTION DETECTION function can be fro- zen for two seconds after pressing the STOP button to stop the Alarm recording, which will override and halt Alarm Recording. Settings can then be made for other functions during this time. If settings are not altered, the unit will automatically return to re- cording after two seconds.
As the ALARM IN terminals located on the unit’s rear are always active, their input signals are given
priority during Alarm Recording. In addition, when the MOTION DETECTION function has been acti- vated, Alarm Recording will begin depending on the input signals from each of the terminals.
The MOTION DETECTION function cannot be accessed when menus are left open.
The
There may be cases when the unit’s built- in MOTION DETECTION function does not operate properly due to external condition or video input signal or other factors.
When you wish to use the MOTION DETECTION function to activate Alarm Recording, the CAMERA
CH of the cameras to be used must be set to some- thing other than “ - ” in the PRI (priority) setting of the DEFINE ALARM GROUP menu.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• | •••••••••••• | • |
40
