Manuals / NetComm / Computer Equipment / Switch

NetComm NP2624M manual Tftp Firmware update, Set IP Address

Models: NP2624M

1 134

Download 134 pages 9.07 Kb

Page 59

3.2 TFTP Firmware update

We provide the TFTP client to update ﬁrmware from Ethernet. The user has to ﬁrst install TFTP server on their PC and place the image in the download folder.

1. Press “3” to start TFTP update ﬁrmware.

2.Enter the Switch IP address and press “Enter” to accept default value.

3.Enter the TFTP Server IP address and press “Enter” to accept default value.

4.Enter the File name to download. Press “Enter” to accept default value and the TFTP download will begin and the ﬁrmware will be updated.

3.3Set IP Address

A shortcut to set switch IP address and gateway before switch system initialization has also been provided. This saves time as the switch IP can be changed without the need to wait for the system to boot up and reconﬁgure.

1.Press “4” to start IP setup.

2.Enter the Switch IP address. Press “Enter” to accept the default value.

3.Enter the Mask. Press “Enter” to accept the default value.

4.Enter the Gateway IP address. Press “Enter” to accept the default value.

NP2624M User Guide	59
YML827 Rev1

Image 59

NetComm NP2624M manual Tftp Firmware update, Set IP Address

Contents

Page Contents Introduction Unpacking Power on InstallationDesktop or Shelf Installation Rack InstallationAccess your Switch Initial set up for managementIn-band Management through Ethernet Connecting without a Dhcp serverTelnet management Telnet IPAddressofSwitch10/100M LED indicators informationColor Status Solid Blinking Power Web Management Home Overview Switch InformationPort status Single port counter and status Port Statistics NP2624M User Guide Show MAC Table Administrator IP and Management mode Max bridge transit Make sure Max bridge transit delay bound control is enabledWorks under Max bridge transit delay bound control Miscellaneous Configuration Priority Queue Service settingsConsole Port Information Port Controls Security EgressPriority Group ID Aggregator settingTrunking System PriorityAggregator Information No select State ActivityActive select Report Filter DatabaseIgmp Snooping QueryStatic MAC Address MAC filtering Support Port-based Vlan Vlan configurationSupport Protocol-based Vlan Support Tag-based Vlan Ieee 802.1Q VlanPort Based Vlan Basic 7.2 .1Q VlanIeee 802.1q NP2624M. Users set the VID to mark the packet fromIngress Filtering Port VIDPort VID Pvid Rapid Spanning Tree Hello Time Forward Delay TimeMax Age Edge Port Port NumberPath Cost Port PriorityMonitored Port Roving Analysis ModePort Mirror Analysis PortTrap Manager SNMP/Trap ManagerSystem Options Community StringsSecurity Manager Perport Configuration Tx Period Supplicant TimeoutServer Timeout Quiet PeriodPing Agent Management Single IPLaunch Manager Agent ManagerAgent Control Port Add/Edit/DeleteStacking Management Commands from agent manager cannot pass over currentWill cause an unexpected forwarding error here To delete an existing member, choose the host Manual methodComplete the addition of a new member Editing an existing member is also easy to doURL of the master switch IP no matter how the agent manager Case of the http// authentication mechanism, the webBrowser will always ask the administrator to input username Password when agent manager changes a new host. Typically,Link Status Stacking ManagerAdd a Vlan NP2624M User Guide YML827 Rev1 Cannot be edited Edit or Delete a VlanPvid Setup Tftp Update Firmware Tftp Backup Configuration Configuration BackupTftp Restore Configuration Event Logging Reset SystemReboot Console Boot Loader 1K X modem Firmware update Set IP Address Tftp Firmware updateDiagnose Sdram Out-of-band Terminal mode management Conﬁguration Main MenuControl Keys Action Menu Line Switch Static ConfigurationPort Configuration Trunk Configuration Port 26, and you can configure them as aboveVlan Configure Ingress Filter 2 UnTagged Pkt Create a Vlan Group Create Port-Based Vlan Port26, and you can configure if necessaryCreate 802.1Q Vlan After port 26, and you can configure them if necessaryEdit / Delete a Vlan Group Groups Sorted Mode Edit/Delete a Vlan Group page, the result of sorted by VID Ping Miscellaneous ConfigurationBroadcast Storm Filtering MAC Age IntervalMaximum bridge transmit delay bound Collisions Retry Forever Port SecurityIFG Compensation Hash AlgorithmChange Username Administration ConfigurationDevice Information Change PasswordIP Configuration Port Mirror Configuration Port Static Priority Priority Configuration7.2 .1P Priority Configuration MAC Address Configuration Add static MAC address Delete static MAC address Edit static MAC addressAdd filter MAC address Filtering MAC AddressDelete filter MAC address Edit filter MAC addressProtocol Related Configuration Rstp Enable/Disable RstpRstp System Configuration Per port Configuration Snmp Unrestricted Add Community NameRestricted Delete Community Name Edit Community NameAdd Snmp trap manager Trap ManagersDelete trap manager Edit trap managersIgmp Created automatically Working Port SettingLacp Link Aggregation Control Protocol On the page of Trunk Configuration first Static trunk group Lacp trunk group Lacp Status5 .1x Protocol Enable/Disable5.3 .1x PerPort Configuration 5.2 .1x System ConfigurationFa Force the specific port to be authorized Authentication5.4 .1x Miscellaneous Configuration Fu Force the specific port to be unauthorizedPort Status Status and CountersPort Counters System Information Restart Reboot SwitchDefault Tftp Update Firmware Backup Configure File Restore Configure FileBenefits of VLANs Vlan application used with switchNP2624M User Guide 111 YML827 Rev1 Single IP Agent mode application used with switch Trunking Application used with switchNo up-link limitation through Gigabit port Reduce the demand of real IP public IPMaster and slave switches in the same LAN domain Typical setup of Single IP-Agent mode networkMaster in WAN domain and slaves in LAN domain Master and slave switches in different LAN domain116 No redundant hardware required Single IP Stacking mode application used with switchTypical connections for switch management by stacking Well integrated UI to view status of stacking switchesAdd stacking members in the Stacking management Guide to build up Stacking SwitchesConnect switches with Giga port in serial sequence Easy adding or removal stacking memberVlan ID An Example of Port-Base Stacking Vlan120 Issue on Trunk and Stacking mode Compatibility on Virtual Server and Single IP Agent/Stacking Manager IP should be changed back to the Switch IP before launchingCommunication Access point802.11g AppletFirewall Enterprise networkEthernet Fast EthernetInternet GatewayGroup IntranetPPPoE NetworkNWay Protocol Subnet mask ProtocolServer StationWindows TransceiverUser Name Utility100Mbps RJ-45 Network PortsPair connection does not exceed 100 metres 10MbpsCross-Over Cabling Straight and crossover cable configurationStraight-Through Cabling Customer Information Contact InformationCopyright Information Limitations of Warranty Product Warranty