Manuals / NetComm / Computer Equipment / Switch

NetComm NP2624M manual Per port Configuration

Models: NP2624M

1 134

Download 134 pages 9.07 Kb

Page 91

4.3.1.3. Per port Configuration

1.PortState: Displays spanning tree status about the switch which per port is forwarding or blocking.

2.Select <Edit>.

3.PathCost: Speciﬁes the path cost of the port that the switch uses to determine which ports are the forwarding ports.

4.Priority: The Priority Port allows you to make it more or less likely to become the root port.

5.EdgePort: If the port connected to a device does not understand STP or RSTP, you can set as “No”. This means the switch will stay in the forwarding state.

6.Press Ctrl +A to go back to the action menu line.

7.Select <Save> to save all conﬁgured values.

8.On the action menu line you can press <Next Page> to conﬁgure port9 ~ port26, press <Previous Page> return to last page.

NOTE:	For more information on parameter descriptions please see section
	2-4-8.

NP2624M User Guide	91
YML827 Rev1

Image 91

NetComm NP2624M manual Per port Configuration

Contents

Page Contents Introduction Unpacking Power on InstallationDesktop or Shelf Installation Rack InstallationAccess your Switch Initial set up for managementIn-band Management through Ethernet Connecting without a Dhcp serverTelnet management Telnet IPAddressofSwitchColor Status Solid Blinking Power LED indicators information10/100M Web Management Home Overview Switch InformationPort status Single port counter and status Port Statistics NP2624M User Guide Show MAC Table Administrator IP and Management mode Works under Max bridge transit delay bound control Make sure Max bridge transit delay bound control is enabledMax bridge transit Miscellaneous Configuration Priority Queue Service settingsConsole Port Information Port Controls Priority EgressSecurity Group ID Aggregator settingTrunking System PriorityAggregator Information Active select State ActivityNo select Report Filter DatabaseIgmp Snooping QueryStatic MAC Address MAC filtering Support Port-based Vlan Vlan configurationSupport Protocol-based Vlan Support Tag-based Vlan Ieee 802.1Q VlanPort Based Vlan Basic 7.2 .1Q VlanIeee 802.1q NP2624M. Users set the VID to mark the packet fromPort VID Pvid Port VIDIngress Filtering Rapid Spanning Tree Max Age Forward Delay TimeHello Time Edge Port Port NumberPath Cost Port PriorityMonitored Port Roving Analysis ModePort Mirror Analysis PortTrap Manager SNMP/Trap ManagerSystem Options Community StringsSecurity Manager Perport Configuration Tx Period Supplicant TimeoutServer Timeout Quiet PeriodPing Agent Management Single IPLaunch Manager Agent ManagerAgent Control Port Add/Edit/DeleteWill cause an unexpected forwarding error here Commands from agent manager cannot pass over currentStacking Management To delete an existing member, choose the host Manual methodComplete the addition of a new member Editing an existing member is also easy to doURL of the master switch IP no matter how the agent manager Case of the http// authentication mechanism, the webBrowser will always ask the administrator to input username Password when agent manager changes a new host. Typically,Link Status Stacking ManagerAdd a Vlan NP2624M User Guide YML827 Rev1 Cannot be edited Edit or Delete a VlanPvid Setup Tftp Update Firmware Tftp Restore Configuration Configuration BackupTftp Backup Configuration Reboot Reset SystemEvent Logging Console Boot Loader 1K X modem Firmware update Set IP Address Tftp Firmware updateDiagnose Sdram Out-of-band Terminal mode management Control Keys Main MenuConﬁguration Action Menu Line Switch Static ConfigurationPort Configuration Trunk Configuration Port 26, and you can configure them as aboveVlan Configure Ingress Filter 2 UnTagged Pkt Create a Vlan Group Create Port-Based Vlan Port26, and you can configure if necessaryCreate 802.1Q Vlan After port 26, and you can configure them if necessaryEdit / Delete a Vlan Group Groups Sorted Mode Edit/Delete a Vlan Group page, the result of sorted by VID Ping Miscellaneous ConfigurationBroadcast Storm Filtering MAC Age IntervalMaximum bridge transmit delay bound Collisions Retry Forever Port SecurityIFG Compensation Hash AlgorithmChange Username Administration ConfigurationDevice Information Change PasswordIP Configuration Port Mirror Configuration Port Static Priority Priority Configuration7.2 .1P Priority Configuration MAC Address Configuration Add static MAC address Delete static MAC address Edit static MAC addressAdd filter MAC address Filtering MAC AddressDelete filter MAC address Edit filter MAC addressProtocol Related Configuration Rstp System Configuration Enable/Disable RstpRstp Per port Configuration Snmp Restricted Add Community NameUnrestricted Delete Community Name Edit Community NameAdd Snmp trap manager Trap ManagersDelete trap manager Edit trap managersIgmp Lacp Link Aggregation Control Protocol Working Port SettingCreated automatically On the page of Trunk Configuration first Static trunk group Lacp trunk group Lacp Status5 .1x Protocol Enable/Disable5.3 .1x PerPort Configuration 5.2 .1x System ConfigurationFa Force the specific port to be authorized Authentication5.4 .1x Miscellaneous Configuration Fu Force the specific port to be unauthorizedPort Status Status and CountersPort Counters System Information Default Reboot SwitchRestart Tftp Update Firmware Backup Configure File Restore Configure FileBenefits of VLANs Vlan application used with switchNP2624M User Guide 111 YML827 Rev1 Single IP Agent mode application used with switch Trunking Application used with switchNo up-link limitation through Gigabit port Reduce the demand of real IP public IPMaster and slave switches in the same LAN domain Typical setup of Single IP-Agent mode networkMaster in WAN domain and slaves in LAN domain Master and slave switches in different LAN domain116 No redundant hardware required Single IP Stacking mode application used with switchTypical connections for switch management by stacking Well integrated UI to view status of stacking switchesAdd stacking members in the Stacking management Guide to build up Stacking SwitchesConnect switches with Giga port in serial sequence Easy adding or removal stacking memberVlan ID An Example of Port-Base Stacking Vlan120 Issue on Trunk and Stacking mode Compatibility on Virtual Server and Single IP Agent/Stacking Manager IP should be changed back to the Switch IP before launchingCommunication Access point802.11g AppletFirewall Enterprise networkEthernet Fast EthernetInternet GatewayGroup IntranetNWay Protocol NetworkPPPoE Subnet mask ProtocolServer StationWindows TransceiverUser Name Utility100Mbps RJ-45 Network PortsPair connection does not exceed 100 metres 10MbpsStraight-Through Cabling Straight and crossover cable configurationCross-Over Cabling Copyright Information Contact InformationCustomer Information Limitations of Warranty Product Warranty