Max bridge transit | NetComm NP2624M specs

2.5.2Switch Setting 2.5.2.1 Advanced

MAC Address Age-out Time: Type the number of seconds that an inactive MAC address remains in the switch’s address table. The valid range is 300~765 seconds. Default is 300 seconds.

Max bridge transit

delay bound control:Limits the packets queuing time in switch. If enabled, the excess packets will be dropped. These valid values are 1 sec, 2 sec, and 4 sec and off. Default is 1 seconds.

NOTE:	Make sure “Max bridge transit delay bound control” is enabled
	before “Enable Delay Bound”, because “Enable Delay Bound” only
	works under “Max bridge transit delay bound control”.

Enable Delay Bound:Limit the low priority packets queuing time in switch. Default Max Delay Time is 255ms. If the amount of time a low priority packet stays in the switch exceeds the Max Delay Time, it will be sent.

The valid range is 1-255ms.

Broadcast Storm Filter: To conﬁgure broadcast storm control, enable it and set the upper threshold for individual ports. The threshold is the percentage of the port’s total bandwidth used by broadcast trafﬁc. When broadcast trafﬁc for a port rises above the threshold you set, broadcast storm control becomes active. The valid threshold value is 5%, 10%, 15%, 20%, 25% and off.

18	NP2624M User Guide
	YML827 Rev1

Image 18

NetComm NP2624M manual Make sure Max bridge transit delay bound control is enabled

Contents

Page Contents Introduction Unpacking Rack Installation InstallationDesktop or Shelf Installation Power on Initial set up for management Access your Switch Connecting without a Dhcp server In-band Management through Ethernet Telnet IPAddressofSwitch Telnet management LED indicators information Color Status Solid Blinking Power10/100M Switch Information Web Management Home Overview Port status Single port counter and status Port Statistics NP2624M User Guide Show MAC Table Administrator IP and Management mode Make sure Max bridge transit delay bound control is enabled Works under Max bridge transit delay bound controlMax bridge transit Priority Queue Service settings Miscellaneous Configuration Console Port Information Port Controls Egress PrioritySecurity System Priority Aggregator settingTrunking Group ID Aggregator Information State Activity Active selectNo select Query Filter DatabaseIgmp Snooping Report Static MAC Address MAC filtering Vlan configuration Support Port-based Vlan Support Tag-based Vlan Ieee 802.1Q Vlan Support Protocol-based Vlan Port Based Vlan 7.2 .1Q Vlan Basic NP2624M. Users set the VID to mark the packet from Ieee 802.1q Port VID Port VID PvidIngress Filtering Rapid Spanning Tree Forward Delay Time Max AgeHello Time Port Priority Port NumberPath Cost Edge Port Analysis Port Roving Analysis ModePort Mirror Monitored Port Community Strings SNMP/Trap ManagerSystem Options Trap Manager Security Manager Perport Configuration Quiet Period Supplicant TimeoutServer Timeout Tx Period Ping Single IP Agent Management Add/Edit/Delete Agent ManagerAgent Control Port Launch Manager Commands from agent manager cannot pass over current Will cause an unexpected forwarding error hereStacking Management Editing an existing member is also easy to do Manual methodComplete the addition of a new member To delete an existing member, choose the host Password when agent manager changes a new host. Typically, Case of the http// authentication mechanism, the webBrowser will always ask the administrator to input username URL of the master switch IP no matter how the agent manager Stacking Manager Link Status Add a Vlan NP2624M User Guide YML827 Rev1 Edit or Delete a Vlan Cannot be edited Pvid Setup Tftp Update Firmware Configuration Backup Tftp Restore ConfigurationTftp Backup Configuration Reset System RebootEvent Logging Console Boot Loader 1K X modem Firmware update Tftp Firmware update Set IP Address Diagnose Sdram Out-of-band Terminal mode management Main Menu Control KeysConﬁguration Switch Static Configuration Action Menu Line Port Configuration Port 26, and you can configure them as above Trunk Configuration Vlan Configure Ingress Filter 2 UnTagged Pkt Port26, and you can configure if necessary Create a Vlan Group Create Port-Based Vlan After port 26, and you can configure them if necessary Create 802.1Q Vlan Edit / Delete a Vlan Group Groups Sorted Mode Edit/Delete a Vlan Group page, the result of sorted by VID Miscellaneous Configuration Ping MAC Age Interval Broadcast Storm Filtering Maximum bridge transmit delay bound Port Security Collisions Retry Forever Hash Algorithm IFG Compensation Administration Configuration Change Username Change Password Device Information IP Configuration Port Mirror Configuration Priority Configuration Port Static Priority 7.2 .1P Priority Configuration MAC Address Configuration Add static MAC address Edit static MAC address Delete static MAC address Filtering MAC Address Add filter MAC address Edit filter MAC address Delete filter MAC address Protocol Related Configuration Enable/Disable Rstp Rstp System ConfigurationRstp Per port Configuration Snmp Add Community Name RestrictedUnrestricted Edit Community Name Delete Community Name Trap Managers Add Snmp trap manager Edit trap managers Delete trap manager Igmp Working Port Setting Lacp Link Aggregation Control ProtocolCreated automatically On the page of Trunk Configuration first Lacp Status Static trunk group Lacp trunk group Enable/Disable 5 .1x Protocol 5.2 .1x System Configuration 5.3 .1x PerPort Configuration Fu Force the specific port to be unauthorized Authentication5.4 .1x Miscellaneous Configuration Fa Force the specific port to be authorized Status and Counters Port Status Port Counters System Information Reboot Switch DefaultRestart Tftp Update Firmware Restore Configure File Backup Configure File Vlan application used with switch Benefits of VLANs NP2624M User Guide 111 YML827 Rev1 Trunking Application used with switch Single IP Agent mode application used with switch Reduce the demand of real IP public IP No up-link limitation through Gigabit port Typical setup of Single IP-Agent mode network Master and slave switches in the same LAN domain Master and slave switches in different LAN domain Master in WAN domain and slaves in LAN domain 116 Well integrated UI to view status of stacking switches Single IP Stacking mode application used with switchTypical connections for switch management by stacking No redundant hardware required Easy adding or removal stacking member Guide to build up Stacking SwitchesConnect switches with Giga port in serial sequence Add stacking members in the Stacking management An Example of Port-Base Stacking Vlan Vlan ID 120 Issue on Trunk and Stacking mode Compatibility on Virtual Server and Single IP IP should be changed back to the Switch IP before launching Agent/Stacking Manager Applet Access point802.11g Communication Fast Ethernet Enterprise networkEthernet Firewall Intranet GatewayGroup Internet Network NWay ProtocolPPPoE Station ProtocolServer Subnet mask Utility TransceiverUser Name Windows 10Mbps RJ-45 Network PortsPair connection does not exceed 100 metres 100Mbps Straight and crossover cable configuration Straight-Through CablingCross-Over Cabling Contact Information Copyright InformationCustomer Information Product Warranty Limitations of Warranty