Manuals / NetComm / Computer Equipment / Switch

NetComm NP2624M manual Port Mirror Configuration

Models: NP2624M

1 134

Download 134 pages 9.07 Kb

Page 81

4.2.6. Port Mirror Configuration

Port mirroring is a method for monitoring trafﬁc in switched networks. Trafﬁc through ports can be monitored by one speciﬁc port. That is, trafﬁc going in or out of monitored ports will be duplicated into the monitoring port.

Press the Space key to change conﬁgure of per item.

1.Select <Edit>.

2.Sniffer Mode: Press the Space key to set the sniffer mode to Disable,Rx,Tx or Both.

3.Monitoring Port: The sniffer port can be used to see all monitored ports trafﬁc. Press the Space key to choose it.

4.Monitored Port: The ports you want to monitor. All monitored ports trafﬁc will be copied to the sniffer port. You can select a maximum of 25 ports to monitor in the switch. Users can choose which port to monitor in the sniffer mode. Press Space key to choose member port, “V” – denotes a member, “—” – is not a member.

5.Press Ctrl+A to go back to the action menu line

6.Select <Save> to save all conﬁgured values.

7.On the action menu line you can press <Next Page> to conﬁgure port9 ~ port26, press <Previous Page> return to last page.

NOTE:

Only one sniffer mode is active in the switch at a time.

NP2624M User Guide	81
YML827 Rev1

Image 81

NetComm NP2624M manual Port Mirror Configuration

Contents

Page Contents Introduction Unpacking Desktop or Shelf Installation InstallationRack Installation Power onAccess your Switch Initial set up for managementIn-band Management through Ethernet Connecting without a Dhcp serverTelnet management Telnet IPAddressofSwitchLED indicators information Color Status Solid Blinking Power10/100M Web Management Home Overview Switch InformationPort status Single port counter and status Port Statistics NP2624M User Guide Show MAC Table Administrator IP and Management mode Make sure Max bridge transit delay bound control is enabled Works under Max bridge transit delay bound controlMax bridge transit Miscellaneous Configuration Priority Queue Service settingsConsole Port Information Port Controls Egress PrioritySecurity Trunking Aggregator settingSystem Priority Group IDAggregator Information State Activity Active selectNo select Igmp Snooping Filter DatabaseQuery ReportStatic MAC Address MAC filtering Support Port-based Vlan Vlan configurationSupport Protocol-based Vlan Support Tag-based Vlan Ieee 802.1Q VlanPort Based Vlan Basic 7.2 .1Q VlanIeee 802.1q NP2624M. Users set the VID to mark the packet fromPort VID Port VID PvidIngress Filtering Rapid Spanning Tree Forward Delay Time Max AgeHello Time Path Cost Port NumberPort Priority Edge PortPort Mirror Roving Analysis ModeAnalysis Port Monitored PortSystem Options SNMP/Trap ManagerCommunity Strings Trap ManagerSecurity Manager Perport Configuration Server Timeout Supplicant TimeoutQuiet Period Tx PeriodPing Agent Management Single IPAgent Control Port Agent ManagerAdd/Edit/Delete Launch ManagerCommands from agent manager cannot pass over current Will cause an unexpected forwarding error hereStacking Management Complete the addition of a new member Manual methodEditing an existing member is also easy to do To delete an existing member, choose the hostBrowser will always ask the administrator to input username Case of the http// authentication mechanism, the webPassword when agent manager changes a new host. Typically, URL of the master switch IP no matter how the agent managerLink Status Stacking ManagerAdd a Vlan NP2624M User Guide YML827 Rev1 Cannot be edited Edit or Delete a VlanPvid Setup Tftp Update Firmware Configuration Backup Tftp Restore ConfigurationTftp Backup Configuration Reset System RebootEvent Logging Console Boot Loader 1K X modem Firmware update Set IP Address Tftp Firmware updateDiagnose Sdram Out-of-band Terminal mode management Main Menu Control KeysConﬁguration Action Menu Line Switch Static ConfigurationPort Configuration Trunk Configuration Port 26, and you can configure them as aboveVlan Configure Ingress Filter 2 UnTagged Pkt Create a Vlan Group Create Port-Based Vlan Port26, and you can configure if necessaryCreate 802.1Q Vlan After port 26, and you can configure them if necessaryEdit / Delete a Vlan Group Groups Sorted Mode Edit/Delete a Vlan Group page, the result of sorted by VID Ping Miscellaneous ConfigurationBroadcast Storm Filtering MAC Age IntervalMaximum bridge transmit delay bound Collisions Retry Forever Port SecurityIFG Compensation Hash AlgorithmChange Username Administration ConfigurationDevice Information Change PasswordIP Configuration Port Mirror Configuration Port Static Priority Priority Configuration7.2 .1P Priority Configuration MAC Address Configuration Add static MAC address Delete static MAC address Edit static MAC addressAdd filter MAC address Filtering MAC AddressDelete filter MAC address Edit filter MAC addressProtocol Related Configuration Enable/Disable Rstp Rstp System ConfigurationRstp Per port Configuration Snmp Add Community Name RestrictedUnrestricted Delete Community Name Edit Community NameAdd Snmp trap manager Trap ManagersDelete trap manager Edit trap managersIgmp Working Port Setting Lacp Link Aggregation Control ProtocolCreated automatically On the page of Trunk Configuration first Static trunk group Lacp trunk group Lacp Status5 .1x Protocol Enable/Disable5.3 .1x PerPort Configuration 5.2 .1x System Configuration5.4 .1x Miscellaneous Configuration AuthenticationFu Force the specific port to be unauthorized Fa Force the specific port to be authorizedPort Status Status and CountersPort Counters System Information Reboot Switch DefaultRestart Tftp Update Firmware Backup Configure File Restore Configure FileBenefits of VLANs Vlan application used with switchNP2624M User Guide 111 YML827 Rev1 Single IP Agent mode application used with switch Trunking Application used with switchNo up-link limitation through Gigabit port Reduce the demand of real IP public IPMaster and slave switches in the same LAN domain Typical setup of Single IP-Agent mode networkMaster in WAN domain and slaves in LAN domain Master and slave switches in different LAN domain116 Typical connections for switch management by stacking Single IP Stacking mode application used with switchWell integrated UI to view status of stacking switches No redundant hardware requiredConnect switches with Giga port in serial sequence Guide to build up Stacking SwitchesEasy adding or removal stacking member Add stacking members in the Stacking managementVlan ID An Example of Port-Base Stacking Vlan120 Issue on Trunk and Stacking mode Compatibility on Virtual Server and Single IP Agent/Stacking Manager IP should be changed back to the Switch IP before launching802.11g Access pointApplet CommunicationEthernet Enterprise networkFast Ethernet FirewallGroup GatewayIntranet InternetNetwork NWay ProtocolPPPoE Server ProtocolStation Subnet maskUser Name TransceiverUtility WindowsPair connection does not exceed 100 metres RJ-45 Network Ports10Mbps 100MbpsStraight and crossover cable configuration Straight-Through CablingCross-Over Cabling Contact Information Copyright InformationCustomer Information Limitations of Warranty Product Warranty