RJ-45 Network Ports, 10Mbps, 100Mbps | NetComm NP2624M manual

Appendix B: Cable Information

This cable information is provided for your reference only. Please ensure you only connect the appropriate cable into the correct socket on either this product or your computer.

If you are unsure about which cable to use or which socket to connect it to, please refer to the hardware installation section in this manual. If you are still not sure about cable connections, please contact a professional computer technician or NetComm for further advice.

RJ-45 Network Ports

RJ-45 Network Ports can connect any networking devices that use a standard LAN interface, such as a Hub/Switch Hub or Router. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable to connect the networking device to the RJ-45 Ethernet port. Depending on the type of connection, 10Mbps or 100Mbps, use the following Ethernet cable, as prescribed.

10Mbps:	Use EIA/TIA-568-100-Category 3, 4 or 5 cable.
100Mbps:	Use EIA/TIA-568-100-Category 5 cable.

Note:	To prevent loss of signal, make sure that the length of any twisted-
	pair connection does not exceed 100 metres.

		RJ-45 Connector
		Pin Assignment	Normal Assignment

		1	Input Receive Data +
		2	Input Receive Data -
		3	Output Transmit Data +
		6	Output Transmit Data -
		4,5,7,8	Not used

Figure 1

RJ-45 plug attached to cable

Figure 2

130	NP2624M User Guide
	YML827 Rev1

Image 130

NetComm NP2624M manual RJ-45 Network Ports, Pair connection does not exceed 100 metres, 10Mbps, 100Mbps

Contents

Page Contents Introduction Unpacking Rack Installation InstallationDesktop or Shelf Installation Power on Initial set up for management Access your Switch Connecting without a Dhcp server In-band Management through Ethernet Telnet IPAddressofSwitch Telnet management Color Status Solid Blinking Power LED indicators information10/100M Switch Information Web Management Home Overview Port status Single port counter and status Port Statistics NP2624M User Guide Show MAC Table Administrator IP and Management mode Works under Max bridge transit delay bound control Make sure Max bridge transit delay bound control is enabledMax bridge transit Priority Queue Service settings Miscellaneous Configuration Console Port Information Port Controls Priority EgressSecurity System Priority Aggregator settingTrunking Group ID Aggregator Information Active select State ActivityNo select Query Filter DatabaseIgmp Snooping Report Static MAC Address MAC filtering Vlan configuration Support Port-based Vlan Support Tag-based Vlan Ieee 802.1Q Vlan Support Protocol-based Vlan Port Based Vlan 7.2 .1Q Vlan Basic NP2624M. Users set the VID to mark the packet from Ieee 802.1q Port VID Pvid Port VIDIngress Filtering Rapid Spanning Tree Max Age Forward Delay TimeHello Time Port Priority Port NumberPath Cost Edge Port Analysis Port Roving Analysis ModePort Mirror Monitored Port Community Strings SNMP/Trap ManagerSystem Options Trap Manager Security Manager Perport Configuration Quiet Period Supplicant TimeoutServer Timeout Tx Period Ping Single IP Agent Management Add/Edit/Delete Agent ManagerAgent Control Port Launch Manager Will cause an unexpected forwarding error here Commands from agent manager cannot pass over currentStacking Management Editing an existing member is also easy to do Manual methodComplete the addition of a new member To delete an existing member, choose the host Password when agent manager changes a new host. Typically, Case of the http// authentication mechanism, the webBrowser will always ask the administrator to input username URL of the master switch IP no matter how the agent manager Stacking Manager Link Status Add a Vlan NP2624M User Guide YML827 Rev1 Edit or Delete a Vlan Cannot be edited Pvid Setup Tftp Update Firmware Tftp Restore Configuration Configuration BackupTftp Backup Configuration Reboot Reset SystemEvent Logging Console Boot Loader 1K X modem Firmware update Tftp Firmware update Set IP Address Diagnose Sdram Out-of-band Terminal mode management Control Keys Main MenuConﬁguration Switch Static Configuration Action Menu Line Port Configuration Port 26, and you can configure them as above Trunk Configuration Vlan Configure Ingress Filter 2 UnTagged Pkt Port26, and you can configure if necessary Create a Vlan Group Create Port-Based Vlan After port 26, and you can configure them if necessary Create 802.1Q Vlan Edit / Delete a Vlan Group Groups Sorted Mode Edit/Delete a Vlan Group page, the result of sorted by VID Miscellaneous Configuration Ping MAC Age Interval Broadcast Storm Filtering Maximum bridge transmit delay bound Port Security Collisions Retry Forever Hash Algorithm IFG Compensation Administration Configuration Change Username Change Password Device Information IP Configuration Port Mirror Configuration Priority Configuration Port Static Priority 7.2 .1P Priority Configuration MAC Address Configuration Add static MAC address Edit static MAC address Delete static MAC address Filtering MAC Address Add filter MAC address Edit filter MAC address Delete filter MAC address Protocol Related Configuration Rstp System Configuration Enable/Disable RstpRstp Per port Configuration Snmp Restricted Add Community NameUnrestricted Edit Community Name Delete Community Name Trap Managers Add Snmp trap manager Edit trap managers Delete trap manager Igmp Lacp Link Aggregation Control Protocol Working Port SettingCreated automatically On the page of Trunk Configuration first Lacp Status Static trunk group Lacp trunk group Enable/Disable 5 .1x Protocol 5.2 .1x System Configuration 5.3 .1x PerPort Configuration Fu Force the specific port to be unauthorized Authentication5.4 .1x Miscellaneous Configuration Fa Force the specific port to be authorized Status and Counters Port Status Port Counters System Information Default Reboot SwitchRestart Tftp Update Firmware Restore Configure File Backup Configure File Vlan application used with switch Benefits of VLANs NP2624M User Guide 111 YML827 Rev1 Trunking Application used with switch Single IP Agent mode application used with switch Reduce the demand of real IP public IP No up-link limitation through Gigabit port Typical setup of Single IP-Agent mode network Master and slave switches in the same LAN domain Master and slave switches in different LAN domain Master in WAN domain and slaves in LAN domain 116 Well integrated UI to view status of stacking switches Single IP Stacking mode application used with switchTypical connections for switch management by stacking No redundant hardware required Easy adding or removal stacking member Guide to build up Stacking SwitchesConnect switches with Giga port in serial sequence Add stacking members in the Stacking management An Example of Port-Base Stacking Vlan Vlan ID 120 Issue on Trunk and Stacking mode Compatibility on Virtual Server and Single IP IP should be changed back to the Switch IP before launching Agent/Stacking Manager Applet Access point802.11g Communication Fast Ethernet Enterprise networkEthernet Firewall Intranet GatewayGroup Internet NWay Protocol NetworkPPPoE Station ProtocolServer Subnet mask Utility TransceiverUser Name Windows 10Mbps RJ-45 Network PortsPair connection does not exceed 100 metres 100Mbps Straight-Through Cabling Straight and crossover cable configurationCross-Over Cabling Copyright Information Contact InformationCustomer Information Product Warranty Limitations of Warranty