Manuals / NetComm / Computer Equipment / Switch

NetComm NP2624M manual Telnet management, Telnet IPAddressofSwitch

Models: NP2624M

1 134

Download 134 pages 9.07 Kb

Page 8

1.3.3 Telnet management

In addition to local terminal mode operation, the NP2624M switch supports remote management through Telnet over a network or the internet without a web browser. In this mode, the user has to enter the same settings as required in in-band management to the IP Conﬁguration before executing the Telnet program. Again, after properly setting the switch, save the settings and connect your Ethernet cable from your PC to any port of the Switch. Then you simply type the following at the command line to access the switch:

Telnet IP_Address_of_Switch

The following window appears. Follow the prompts and type in the “username” and “password” to proceed. Refer to the instructions in chapter 3 of this manual for more information.

8	NP2624M User Guide
	YML827 Rev1

Image 8

NetComm NP2624M manual Telnet management, Telnet IPAddressofSwitch

Contents

Page Contents Introduction Unpacking Installation Desktop or Shelf InstallationRack Installation Power onInitial set up for management Access your SwitchConnecting without a Dhcp server In-band Management through EthernetTelnet IPAddressofSwitch Telnet management10/100M LED indicators informationColor Status Solid Blinking Power Switch Information Web Management Home OverviewPort status Single port counter and status Port Statistics NP2624M User Guide Show MAC Table Administrator IP and Management mode Max bridge transit Make sure Max bridge transit delay bound control is enabledWorks under Max bridge transit delay bound control Priority Queue Service settings Miscellaneous ConfigurationConsole Port Information Port Controls Security EgressPriority Aggregator setting TrunkingSystem Priority Group IDAggregator Information No select State ActivityActive select Filter Database Igmp SnoopingQuery ReportStatic MAC Address MAC filtering Vlan configuration Support Port-based VlanSupport Tag-based Vlan Ieee 802.1Q Vlan Support Protocol-based VlanPort Based Vlan 7.2 .1Q Vlan BasicNP2624M. Users set the VID to mark the packet from Ieee 802.1qIngress Filtering Port VIDPort VID Pvid Rapid Spanning Tree Hello Time Forward Delay TimeMax Age Port Number Path CostPort Priority Edge PortRoving Analysis Mode Port MirrorAnalysis Port Monitored PortSNMP/Trap Manager System OptionsCommunity Strings Trap ManagerSecurity Manager Perport Configuration Supplicant Timeout Server TimeoutQuiet Period Tx PeriodPing Single IP Agent ManagementAgent Manager Agent Control PortAdd/Edit/Delete Launch ManagerStacking Management Commands from agent manager cannot pass over currentWill cause an unexpected forwarding error here Manual method Complete the addition of a new memberEditing an existing member is also easy to do To delete an existing member, choose the hostCase of the http// authentication mechanism, the web Browser will always ask the administrator to input usernamePassword when agent manager changes a new host. Typically, URL of the master switch IP no matter how the agent managerStacking Manager Link StatusAdd a Vlan NP2624M User Guide YML827 Rev1 Edit or Delete a Vlan Cannot be editedPvid Setup Tftp Update Firmware Tftp Backup Configuration Configuration BackupTftp Restore Configuration Event Logging Reset SystemReboot Console Boot Loader 1K X modem Firmware update Tftp Firmware update Set IP AddressDiagnose Sdram Out-of-band Terminal mode management Conﬁguration Main MenuControl Keys Switch Static Configuration Action Menu LinePort Configuration Port 26, and you can configure them as above Trunk ConfigurationVlan Configure Ingress Filter 2 UnTagged Pkt Port26, and you can configure if necessary Create a Vlan Group Create Port-Based VlanAfter port 26, and you can configure them if necessary Create 802.1Q VlanEdit / Delete a Vlan Group Groups Sorted Mode Edit/Delete a Vlan Group page, the result of sorted by VID Miscellaneous Configuration PingMAC Age Interval Broadcast Storm FilteringMaximum bridge transmit delay bound Port Security Collisions Retry ForeverHash Algorithm IFG CompensationAdministration Configuration Change UsernameChange Password Device InformationIP Configuration Port Mirror Configuration Priority Configuration Port Static Priority7.2 .1P Priority Configuration MAC Address Configuration Add static MAC address Edit static MAC address Delete static MAC addressFiltering MAC Address Add filter MAC addressEdit filter MAC address Delete filter MAC addressProtocol Related Configuration Rstp Enable/Disable RstpRstp System Configuration Per port Configuration Snmp Unrestricted Add Community NameRestricted Edit Community Name Delete Community NameTrap Managers Add Snmp trap managerEdit trap managers Delete trap managerIgmp Created automatically Working Port SettingLacp Link Aggregation Control Protocol On the page of Trunk Configuration first Lacp Status Static trunk group Lacp trunk groupEnable/Disable 5 .1x Protocol5.2 .1x System Configuration 5.3 .1x PerPort ConfigurationAuthentication 5.4 .1x Miscellaneous ConfigurationFu Force the specific port to be unauthorized Fa Force the specific port to be authorizedStatus and Counters Port StatusPort Counters System Information Restart Reboot SwitchDefault Tftp Update Firmware Restore Configure File Backup Configure FileVlan application used with switch Benefits of VLANsNP2624M User Guide 111 YML827 Rev1 Trunking Application used with switch Single IP Agent mode application used with switchReduce the demand of real IP public IP No up-link limitation through Gigabit portTypical setup of Single IP-Agent mode network Master and slave switches in the same LAN domainMaster and slave switches in different LAN domain Master in WAN domain and slaves in LAN domain116 Single IP Stacking mode application used with switch Typical connections for switch management by stackingWell integrated UI to view status of stacking switches No redundant hardware requiredGuide to build up Stacking Switches Connect switches with Giga port in serial sequenceEasy adding or removal stacking member Add stacking members in the Stacking managementAn Example of Port-Base Stacking Vlan Vlan ID120 Issue on Trunk and Stacking mode Compatibility on Virtual Server and Single IP IP should be changed back to the Switch IP before launching Agent/Stacking ManagerAccess point 802.11gApplet CommunicationEnterprise network EthernetFast Ethernet FirewallGateway GroupIntranet InternetPPPoE NetworkNWay Protocol Protocol ServerStation Subnet maskTransceiver User NameUtility WindowsRJ-45 Network Ports Pair connection does not exceed 100 metres10Mbps 100MbpsCross-Over Cabling Straight and crossover cable configurationStraight-Through Cabling Customer Information Contact InformationCopyright Information Product Warranty Limitations of Warranty