Port status | NetComm NP2624M instruction

2.2. Port status

This page provides current status of every port and the negotiation result.

State:	Displays the port status: On or Down. “Unlink” will
	be treated as “off”.
Link Status:	Displays the link status. Down means “No Link”, Up
	means “Link”.
Auto Negotiation:	Displays the auto negotiation mode: auto/force/
	Nway-force.
Speed status:	Displays the speed, port 1- 24 are 10/100Mbps, Port
	25-26 are 10/100/1000Mbps.
Duplex status:	Displays full-duplex or half-duplex mode.
Flow Control:	Full: Displays the ﬂow control is enabled or disabled
	in full mode.
	Half: Displays the backpressure is enabled or
	disabled in half mode.
Rate Control:	Displays the rate control setting.
	Ingr: Displays the port effective ingress rate of user
	setting.
	Egr: Displays the port effective egress rate of user
	setting.
Port Security:	Displays the port security is enabled or disabled.
Conﬁg:	Displays the state of user setting.
Actual:	Displays the negotiation result.

NP2624M User Guide	11
YML827 Rev1

Image 11

NetComm NP2624M manual Port status

Contents

Page Contents Introduction Unpacking Power on InstallationDesktop or Shelf Installation Rack Installation Access your Switch Initial set up for management In-band Management through Ethernet Connecting without a Dhcp server Telnet management Telnet IPAddressofSwitch 10/100M LED indicators informationColor Status Solid Blinking Power Web Management Home Overview Switch Information Port status Single port counter and status Port Statistics NP2624M User Guide Show MAC Table Administrator IP and Management mode Max bridge transit Make sure Max bridge transit delay bound control is enabledWorks under Max bridge transit delay bound control Miscellaneous Configuration Priority Queue Service settings Console Port Information Port Controls Security EgressPriority Group ID Aggregator settingTrunking System Priority Aggregator Information No select State ActivityActive select Report Filter DatabaseIgmp Snooping Query Static MAC Address MAC filtering Support Port-based Vlan Vlan configuration Support Protocol-based Vlan Support Tag-based Vlan Ieee 802.1Q Vlan Port Based Vlan Basic 7.2 .1Q Vlan Ieee 802.1q NP2624M. Users set the VID to mark the packet from Ingress Filtering Port VIDPort VID Pvid Rapid Spanning Tree Hello Time Forward Delay TimeMax Age Edge Port Port NumberPath Cost Port Priority Monitored Port Roving Analysis ModePort Mirror Analysis Port Trap Manager SNMP/Trap ManagerSystem Options Community Strings Security Manager Perport Configuration Tx Period Supplicant TimeoutServer Timeout Quiet Period Ping Agent Management Single IP Launch Manager Agent ManagerAgent Control Port Add/Edit/Delete Stacking Management Commands from agent manager cannot pass over currentWill cause an unexpected forwarding error here To delete an existing member, choose the host Manual methodComplete the addition of a new member Editing an existing member is also easy to do URL of the master switch IP no matter how the agent manager Case of the http// authentication mechanism, the webBrowser will always ask the administrator to input username Password when agent manager changes a new host. Typically, Link Status Stacking Manager Add a Vlan NP2624M User Guide YML827 Rev1 Cannot be edited Edit or Delete a Vlan Pvid Setup Tftp Update Firmware Tftp Backup Configuration Configuration BackupTftp Restore Configuration Event Logging Reset SystemReboot Console Boot Loader 1K X modem Firmware update Set IP Address Tftp Firmware update Diagnose Sdram Out-of-band Terminal mode management Conﬁguration Main MenuControl Keys Action Menu Line Switch Static Configuration Port Configuration Trunk Configuration Port 26, and you can configure them as above Vlan Configure Ingress Filter 2 UnTagged Pkt Create a Vlan Group Create Port-Based Vlan Port26, and you can configure if necessary Create 802.1Q Vlan After port 26, and you can configure them if necessary Edit / Delete a Vlan Group Groups Sorted Mode Edit/Delete a Vlan Group page, the result of sorted by VID Ping Miscellaneous Configuration Broadcast Storm Filtering MAC Age Interval Maximum bridge transmit delay bound Collisions Retry Forever Port Security IFG Compensation Hash Algorithm Change Username Administration Configuration Device Information Change Password IP Configuration Port Mirror Configuration Port Static Priority Priority Configuration 7.2 .1P Priority Configuration MAC Address Configuration Add static MAC address Delete static MAC address Edit static MAC address Add filter MAC address Filtering MAC Address Delete filter MAC address Edit filter MAC address Protocol Related Configuration Rstp Enable/Disable RstpRstp System Configuration Per port Configuration Snmp Unrestricted Add Community NameRestricted Delete Community Name Edit Community Name Add Snmp trap manager Trap Managers Delete trap manager Edit trap managers Igmp Created automatically Working Port SettingLacp Link Aggregation Control Protocol On the page of Trunk Configuration first Static trunk group Lacp trunk group Lacp Status 5 .1x Protocol Enable/Disable 5.3 .1x PerPort Configuration 5.2 .1x System Configuration Fa Force the specific port to be authorized Authentication5.4 .1x Miscellaneous Configuration Fu Force the specific port to be unauthorized Port Status Status and Counters Port Counters System Information Restart Reboot SwitchDefault Tftp Update Firmware Backup Configure File Restore Configure File Benefits of VLANs Vlan application used with switch NP2624M User Guide 111 YML827 Rev1 Single IP Agent mode application used with switch Trunking Application used with switch No up-link limitation through Gigabit port Reduce the demand of real IP public IP Master and slave switches in the same LAN domain Typical setup of Single IP-Agent mode network Master in WAN domain and slaves in LAN domain Master and slave switches in different LAN domain 116 No redundant hardware required Single IP Stacking mode application used with switchTypical connections for switch management by stacking Well integrated UI to view status of stacking switches Add stacking members in the Stacking management Guide to build up Stacking SwitchesConnect switches with Giga port in serial sequence Easy adding or removal stacking member Vlan ID An Example of Port-Base Stacking Vlan 120 Issue on Trunk and Stacking mode Compatibility on Virtual Server and Single IP Agent/Stacking Manager IP should be changed back to the Switch IP before launching Communication Access point802.11g Applet Firewall Enterprise networkEthernet Fast Ethernet Internet GatewayGroup Intranet PPPoE NetworkNWay Protocol Subnet mask ProtocolServer Station Windows TransceiverUser Name Utility 100Mbps RJ-45 Network PortsPair connection does not exceed 100 metres 10Mbps Cross-Over Cabling Straight and crossover cable configurationStraight-Through Cabling Customer Information Contact InformationCopyright Information Limitations of Warranty Product Warranty