Manuals / NetComm / TV and Video / Home Theater Server

NetComm NP3640 manual Windows 9x/ME Setup

Models: NP3640

1 76

Page 14

Windows 9x/ME Setup

Before performing the following procedure, the Print Server must be installed on your LAN, and configured as described in Section 3. Both the Print Server and the attached printer should be powered ON.

1.Insert the supplied CD-ROM into your drive. If the setup program does not start, run SETUP.exe in the root folder.

2. Click Installation button, then select User Install.

3.Follow the prompts to complete the installation of the Peer-to-peer Printer Port Driver. (Refer to the Windows section of Section 8 - Troubleshooting if there is a problem with the installation.)

4.The Print Driver Setup will then run.

In future, you can use Start -> Programs -> PrintServer Driver -> Printer Port Setup to run the program again.

www.netcomm.com.au	Rev. 1 - YML657
Page 14	NP3640 Fast Ethernet Mini Print Server User Guide

Page 14

Image 14

NetComm NP3640 manual Windows 9x/ME Setup

Contents

Page Page ContentsRev. 1 - YML657 NP3640 Fast Ethernet Mini Print Server User GuideSection 1 - Introduction 1. Preparation Section 2 - Connecting your Mini Print Server4. Power Up 2. Connect the PrinterGreen LED Diagnostic Push ButtonLED Indicators Red LEDAdvanced Configuration and Management Section 3 - Configuring your Mini Print ServerConfiguration Methods Web Based Configuration and ManagementUsing the Windows Wizard Procedure5. Enter the required data on the following screen If the desired Print Server is not listed Which printing method should I use? Section 4 - Configuring your ComputersPrinting Methods OverviewChecking your Network Protocols Windows Windows 2000/XP Setup Windows Peer-to-peer PrintingEnsure the LPR Byte Counting Enabled setting is Enabled 5. On this screen, select Custom, and click the Settings button6. On the Port Settings screen Choose LPR in the Protocol section Enter a Queue nameWindows 9x/ME Setup If desired, click Refresh Management Advanced Port Options Windows SMB Printing Capture Settings Printing from MS-DOS ProgramsWindows with Server-based Print Queues Windows LPR Printing 3. Choose Standard TCP/IP Port, then click New PortMacintosh AppleTalk AppleTalk SetupAdvanced Setup and Management PrintingLPR printing Setup Macintosh OSRequirements Section 5 - BiAdmin Management UtilityInstallation If the desired Print Server is not listed, try the following Printer Status IconsDevice Status Wizard ConfigurationUpgrade Refresh Diagnostics menuMenus ExitConfiguration System TabTCP/IP Tab AppleTalk Tab NetBEUI Tab Internet Printing Tab Logical Port Port TabPhysical Port NetWare SNMP Tab Overview Section 6 - Web-Based ManagementPreparation arp -s IPAddress 00c002xxxxxx UnixServer Status Connecting to the Print ServerConfiguration Screens Connected Printer Configure ServerPrinter Status AppleTalk NetBEUI TCP/IP ConnectionPrint Server Mode GeneralRemote Printer Mode NetWareJob Notification Job notification at only the workstation where the print jobserviced The options areTrap Receivers SNMP Simple Network Management ProtocolManagement Stations Logical Printers Rev. 1 - YML657 Internet PrintingSee Internet Mail Printing in Section 7 for details of this feature NP3640 Fast Ethernet Mini Print Server User GuideInternet Printing Protocol IPP Section 7 - Special FeaturesIPP Server Configuration OverviewInstalling from the CD-ROM IPP Client Setup - Windows 95/98/Me/NT 4.0/XPIPP Client Configuration Windows 95/98/ME/2000/XP/NT Installing using IPPCLIENT.EXEChanging the IPP Port Settings IPP Client Setup - Windows 2000/XP Using IPP Printers Mail Server Internet Mail PrintingSystem Requirements Internet Print ServerInternet Mail Printing Configuration User SoftwareInstallation - User Software Printing through the Internet Using the new PortChecking the Printer Driver Management Station Settings Configuring the Print Server for SNMPSNMP Settings Trap Receiving Station SettingsSection 8 - Troubleshooting OverviewHardware & LAN Problems AppleTalk Macintosh supported by the printer. Try selecting LaserWriter 7 insteadcannot match up the colors as closely as wanted. To alleviate this Novell NetWare is Ready. If it is not, check the error message and perform theWindows Printing Problems setting· Go to Control Panel - Printers and click on your printer.· Problem No Preparing for TCP/IP Printing Section 9 - Network Server ConfigurationWindows NT Server Adding a TCP/IP Remote PrinterWindows NT Printer NameNovell NetWare Configuration Methods Bindery or NDSSetup Wizard Windows 2000 ServerOther Method BiAdminConfiguration Data GeneralCreating an NDPS Manager Object Setup for NDPS NetWareOverview Creating an NDPS Printer Agent Unix Systems Trademarks and NoticesRegistering your NetComm Product Make sure Warranty Registration FormThe following information is vital for your warranty you fill thisPage Rev. 1 - YML657 Product WarrantyLimitations of Warranty NP3640 Fast Ethernet Mini Print Server User Guide